Surplus Record Machinery

LATHES, ENGINE (Also See Lathes, Engine, Gap or Tracer & Copying)

Browse: Machinery Electrical

Machinery & Equipment >

Lathes >

Lathes, Engine

LATHES, ENGINE (Also See Lathes, Engine, Gap or Tracer & Copying)

There are 634 listings in this category
File update: Wed, May 22, 2013 01:22

Advanced Search

Sort by:

Original Sort

9" x 14" Hardinge #HC, chucking lathe, Accurite III 2-Axis DRO, asst. collets & tooling

Trader Machinery Inc, Concord, ON 905-669-7507 (Fax 905-669-7512) Jon Goldman

10" x 18" Hardinge #HLV-EM, 5"4-Jaw,1-1/16"round,11"swing,125-3k RPM, 5C collet,'80

Adams Machinery Co, Lincolnwood, IL 847-673-0556 (Fax 847-673-7636) Sonneborn

10" x 20" Monarch #10EE, 4000 RPM, taper, 5 HP, English gearbox

Monarch Lathes L.P., Sidney, OH 937-492-4111 (Fax 937-492-7958) Scott Foster

10" x 20" Monarch #10EE, 4000 RPM,Solid State Drive,in/mm,6"3-jaw,Aloris,clnt,1983

A Green Co Inc, Worcester, MA 508-791-6800 (Fax 508-791-6838) Harvey Green

10" x 20" Monarch #10EE, 4000 RPM,vari-speed,6"4-Jaw chuck,3 HP,rebuilt,1969

Hoff Machinery, Inc, Minneapolis, MN 612-521-5700 (Fax 612-521-9358) Sales Dept.

10" x 20" Monarch #EE, Inch/Metric, solid state drive, 1983, #1433

Wigglesworth Machinery Co, East Boston, MA 617-567-7210 (Fax 617-561-0265) Gifford

10" x 26" South Bend #Heavy 10, D4 spindle,hard ways,loaded w/tooling,s/n #15111KX16

Astra Tool Co Inc, Grapevine, TX 817-481-6528 (Fax 817-421-5960) David Austin

10" x 30" Monarch #EE, 4000 RPM, 7.5 HP w/backgear, English gearbox

Monarch Lathes L.P., Sidney, OH 937-492-4111 (Fax 937-492-7958) Scott Foster

11" x 18" Hardinge #HLV-H, lathe, 1-1/4"hole, 5C collets, 125-3000 RPM, #6602

Vander Ziel Machinery Sales, Alto, MI 616-868-1111 (Fax 616-868-1115) Steve Vander Ziel

11" x 18" Hardinge #HLV-H, 3-jaw chuck

Richlin Machinery Inc, Farmingdale, NY 631-694-9400 (Fax 631-694-9415) Irv Richlin

11" x 18" Hardinge #TFB-H, toolroom lathe,21"cc,dove tail bed,220V.,3 ph,collet set

Pennsylvania Equipment Inc, Grove City, PA 724-458-6162 (Fax 724-458-0753) Thomas Noone

11" x 30" Harrison #M250, collet closer, inch/metric

Scott Machinery, McClellan, CA 916-638-7718 (Fax 916-638-2450) Deanna Payne

11" x 30" Harrison #M250 lathe, 1.25"spindle bore, 52-2000 RPM, #8993

Vander Ziel Machinery Sales, Alto, MI 616-868-1111 (Fax 616-868-1115) Steve Vander Ziel

12" x 24" Hes #ACC-300, engine lathe,tool post,hyd.tracer att.,hyd.collet closer,Hardinge speed collet chk,coolant sys,#A2000

Sterling Machinery Exchange, South El Monte, CA 626-444-0311 (Fax 626-443-9588) Adam Mattes

12" x 24" Sheldon #EM-46P, face plate, taper, Tag #12617

Yeoman Machinery Corp, Elkhart, IN 574-295-6161 (Fax 574-295-3660) Robert Yeoman

12" x 30" Nardini #TT1230E Turn-Tru, engine lathe,3&4-jaw chucks,tool post,steady rest,D1,1-3/8"spindle bore,#17267

Raco Industrial Corp, Des Plaines, IL 847-298-8600 (Fax 847-635-8976) Jack Boecher

12" x 30" Nardini Turn-Tru #TT-1230E lathe, #8846

Vander Ziel Machinery Sales, Alto, MI 616-868-1111 (Fax 616-868-1115) Steve Vander Ziel

12" x 36" Clausing #5914, 6"3-jaw,1-7/16"cap.,52-2000 RPM,rebuilt & painted

Alenco Tool Supply, Chicago, IL 773-725-5700 (Fax 773-725-0296) Paul Braeseke

12" x 36" Clausing lathe, carriage, tailstock, 1971

GoIndustry Dovebid, Owings Mills, MD 410-654-7500 (Fax 410-654-5876) Jigar Shah

12" x 36" Howa Sangyo #L-200, 3-Jaw chk,threading,tailstock,toolpost,tooling,Ser.32284

M R S Arco Sales, Loves Park, IL 815-633-1285 (Fax 815-633-6774) Donna Richards

12" x 36" Logan #2557V, steady, 5C collets, excellent, 1967, Tag #12826

Yeoman Machinery Corp, Elkhart, IN 574-295-6161 (Fax 574-295-3660) Robert Yeoman

12" BTC, 6-Jaw Chuck, Like New

Row Electrical Eqpt Inc, Toledo, OH 800-248-4479 (Fax 419-244-8887) Jim / Dave

12-1/4" x 36" Enco #10-2030, engine lathe,1-3/8"hole,70-1100 RPM,Standard/Metric threading,7"3-Jaw chuck,hard ways

Hoff Online Auctions, Minneapolis, MN 612-521-5500 (Fax 612-331-3291) Denny Hoff

12-1/2" x 20" Monarch #EE, Solid State V/S drive,4k RPM,taper,3&4-jaw chks,tooling

Century Machinery Co, Los Angeles, CA 213-627-2847 (Fax 213-627-2499) Leon Dietch

12-1/2" x 36" Clausing #5913, engine lathe, 52-2000 RPM, standard threading, hardways, 8"3-Jaw chuck, steady rest, tailstock

Hoff Online Auctions, Minneapolis, MN 612-521-5500 (Fax 612-331-3291) Denny Hoff

12-1/2" x 50" Stanko surface grinder, magnetic base, never used, 2000

Holem Group, Miami, FL 305-733-4644 () Franz Melo

13" x 25" Clausing Colchester #8014, 2500 RPM, in/mm, 6"3-jaw, steady, tool post, coolant, #CK-19511

Action Machinery Co Inc, Bethlehem, PA 610-691-6677 (Fax 610-694-0944) Tom Khoury

13" x 25" Harrison Clausing #V350 lathe, 3250 RPM, 1.65"bore, #9023

Vander Ziel Machinery Sales, Alto, MI 616-868-1111 (Fax 616-868-1115) Steve Vander Ziel

13"/19" x 25" Harrison #M300, Engine Lathe, #5321

IA Machinery Co, Huntington Park, CA 323-587-1887 (Fax 323-587-1811) Rick Kruger

13" x 40" Bridgeport Romi, 7-11/16"o/cross slide,1-9/16"hole,in/mm,5 HP,runs great

Holt Equipment, Hopkins, MN 952-938-2202 (Fax 952-767-0840) Wayne Mader

13" x 40" Clausing Colchester, 1-21/32"hole,#3MT,30-2500 RPM,in/mm,DRO,#6375

Vander Ziel Machinery Sales, Alto, MI 616-868-1111 (Fax 616-868-1115) Steve Vander Ziel

13" x 40" Clausing Colchester lathe, #9836

Vander Ziel Machinery Sales, Alto, MI 616-868-1111 (Fax 616-868-1115) Steve Vander Ziel

13" x 40" Clausing Student #2500, 6"3-jaw chk,in/mm,tlng,3 HP,tailstock,coolant,1993

S & M Machinery Sales Inc, Warren, MI 586-755-1234 (Fax 586-755-9876) Spencer Minns

13" x 40" Harrison #M300, geared head engine lathe,3-jaw chk,KDK tool post,induction hardened ways,splash guard,closer,#A2659

Sterling Machinery Exchange, South El Monte, CA 626-444-0311 (Fax 626-443-9588) Adam Mattes

13" x 40" Jet #GHB-1340, geared head,1.5"spindle hole,70-2000 RPM,2 HP,#015724S

Sominn Machinery Sales, Dodge Center, MN 800-770-5638 (Fax 507-374-6824) J.J. Francis

13" x 40" MSC #951735, geared head,D1-4 spdl,2X Wizard 100 DRO,clnt,rear guard,nice

J Hebert Machine Tool Co., Charlotte, NC 704-825-1511 () Jon Hebert

13" x 40" Sharp #1340, 1-1/2"bore, 1800 RPM, #3422

Turners Machinery Inc, Santa Paula, CA 805-525-2171 (Fax 805-525-5683) Al Van Wagner

13" x 40" South Bend #1340, engine lathe, serial #164794, #5628

IA Machinery Co, Huntington Park, CA 323-587-1887 (Fax 323-587-1811) Rick Kruger

13" x 40" Standard Modern gap, 2k RPM,1-3/8"hole,collet closer,taper,1978,#9303

Turner Industries Inc, Grand Rapids, MI 616-949-5910 (Fax 616-949-3461) Jeff/Bill/David

13" x 42" Clausing Colchester lathe, carriage, tailstock, serial #0000568015

GoIndustry Dovebid, Owings Mills, MD 410-654-7500 (Fax 410-654-5876) Jigar Shah

13" x 50" DoAll /Romi, in/mm thrdg,Dunham air collet chk,air tlstk,live center,#80864

Smith Machinery Co, Ames, IA 515-233-6330 (Fax 515-232-9411) Jim Smith

13" x 60" Clausing Colchester #1360GH, engine lathe, serial #VM0239236, #5436

IA Machinery Co, Huntington Park, CA 323-587-1887 (Fax 323-587-1811) Rick Kruger

13" x 60" Polamco #TUR-50, inch/metric, steady rest, 3-Jaw chuck, tailstock

M R S Arco Sales, Loves Park, IL 815-633-1285 (Fax 815-633-6774) Donna Richards

14" x 24" Pfeifer, steady, metric, collets, chucks, face plates, Tag #13114

Yeoman Machinery Corp, Elkhart, IN 574-295-6161 (Fax 574-295-3660) Robert Yeoman

14" x 30" Takisawa #TSL-800 Max Turn, 8"3-jaw,S/R,collet closer,drill chuck,1978

ACT Inc, Fullerton, CA 714-441-1992 (Fax 714-441-1923) Randy Goodman

14" x 32" Okuma, 7-1/2"swg.cross/slide,2000 RPM,in/mm,tracer,hard ways,#19128

Yoder Machinery Sales, Holland, OH 800-622-4463 (Fax 419-865-5557) Sales

14" x 40" Cadillac #1440, geared head engine lathe,3&4-jaw chuck,5C collet closer,KDK tool post,foot brake,coolant sys,#A2443

Sterling Machinery Exchange, South El Monte, CA 626-444-0311 (Fax 626-443-9588) Adam Mattes

14" x 40" Cadillac #1440 Gear Head, 3-jaw, gap style, Trav-a-Dials, 1993, Tag #15419

Yeoman Machinery Corp, Elkhart, IN 574-295-6161 (Fax 574-295-3660) Robert Yeoman

14"/20" x 40" Jet Gap Bed, 1800 RPM,3&4-Jaw chucks,S.R.,F.R.,univ.gearbox,2006

Jordan Machinery Co Inc, Greenwood, IN 317-882-1478 (Fax 317-887-1487) Jim Jordan

14"/21" x 40" Morton #FEL-1440G, lathe,8.42"SOCS,3-jaw,#4MT,in/mm,1800 RPM,#4809

IA Machinery Co, Huntington Park, CA 323-587-1887 (Fax 323-587-1811) Rick Kruger

14"/21" x 40" Morton #FEL-1440G, lathe,8.42"SOCS,3-jaw,#4MT,in/mm,1800 RPM,#4810

IA Machinery Co, Huntington Park, CA 323-587-1887 (Fax 323-587-1811) Rick Kruger

14" x 40" Nardini #1440, precision gear head, gap bed toolroom lathe

Linden Machine Tools, Natick, MA 508-728-2288 (Fax 508-653-1767) Mike Zirlen

14"/19" x 40" Nardini #MS1440E, gap bed,in/mm,31-2500 RPM,taper,8"3-jaw chuck,coolant,#3MT,clean,#25846

C.W. Wood Machinery Inc, Cincinnati, OH 800-745-6008 (Fax 513-542-4819) Sales Dept.

14" x 40" Nardini #MS-1440E gap, 25-2k RPM,3+4-Jaw,1-3/4"spdl hole,in/mm,1988,#9302

Turner Industries Inc, Grand Rapids, MI 616-949-5910 (Fax 616-949-3461) Jeff/Bill/David

14"/21" x 40" Summit #14, gap bed,in/mm,19-1800 RPM,2"hole,8"3-jaw & 10"4-jaw chuck,7-1/2 HP,SR,FR,1991,#25766

C.W. Wood Machinery Inc, Cincinnati, OH 800-745-6008 (Fax 513-542-4819) Sales Dept.

14"/20" x 40" Victor #1440B, engine lathe, serial #0141522, #5643

IA Machinery Co, Huntington Park, CA 323-587-1887 (Fax 323-587-1811) Rick Kruger

14" x 41" Delta Rockwell engine lathe, 40-1600 RPM,taper,steady rest,clean,9"3-jaw,10"4-jaw,chip pan,2 HP,#25771

C.W. Wood Machinery Inc, Cincinnati, OH 800-745-6008 (Fax 513-542-4819) Sales Dept.

14" x 41" Rockwell #25-209, 9"3-Jaw chk,taper attach.,vari- spd 40-1600 RPM,#1560231

Holt Equipment, Hopkins, MN 952-938-2202 (Fax 952-767-0840) Wayne Mader

14" x 48" Clausing #1401, engine lathe, 3-jaw chuck, splash guard, #A1368

Sterling Machinery Exchange, South El Monte, CA 626-444-0311 (Fax 626-443-9588) Adam Mattes

14" x 60" Simplex, tailstock, toolpost, 9" 3-Jaw chuck

Lee Stevens Machinery Inc., Wixom, MI 248-926-8400 (Fax 248-926-8499) Randy/ Jeff/Chris

14" x 126" Monarch #14C, engine lathe, taper, 3-Jaw chuck, Sony DRO, steady rest, threads, Aloris, 1945, #148014

Machinery Values Inc, Harrison, NJ 973-497-7570 (Fax 973-497-7501) David Valitt

14.5" x 48" Clausing #1500, engine lathe, serial #152162, #5300

IA Machinery Co, Huntington Park, CA 323-587-1887 (Fax 323-587-1811) Rick Kruger

15" x 30" LeBlond lathe, #8713

Vander Ziel Machinery Sales, Alto, MI 616-868-1111 (Fax 616-868-1115) Steve Vander Ziel

15" x 30" LeBlond Regal, 5/8"bore (3356)

Turners Machinery Inc, Santa Paula, CA 805-525-2171 (Fax 805-525-5683) Al Van Wagner

15" x 30" LeBlond Regal, 45-1800 RPM,7-128 TPI,hardways,8"face plate,Newall DP8 2-Axis DRO,9"3-Jaw chuck,10"4-Jaw chuck

Hoff Online Auctions, Minneapolis, MN 612-521-5500 (Fax 612-331-3291) Denny Hoff

15" x 30" LeBlond Regal Servoshift, 45-1800 RPM, taper, 5 HP, 1966

Grand Marshall Machinery Inc, Hauppauge, NY 631-777-3600 (Fax 631-777-3603) Larry/ Paul

15" x 30" LeBlond Regal Servoshift, engine lathe, taper, 3-Jaw chk, Trav-A-Dial, 5 HP, threads, 1966, #150322

Machinery Values Inc, Harrison, NJ 973-497-7570 (Fax 973-497-7501) David Valitt

15" x 40" Merli-Volghera Clover #14/20, gap bed lathe,60-1800 RPM,8"3 point chuck,6"3-point chuck,10"4-point chuck

GoIndustry Dovebid, Owings Mills, MD 410-654-7500 (Fax 410-654-5876) Jigar Shah

15" x 40" Mysore Kirloskar #EM2, gap bed lathe, 8"3 point chuck, serial #102, 1973

GoIndustry Dovebid, Owings Mills, MD 410-654-7500 (Fax 410-654-5876) Jigar Shah

15" x 48" Colchester #15x48, engine lathe, 30-1200 RPM, 10"4-point chuck

GoIndustry Dovebid, Owings Mills, MD 410-654-7500 (Fax 410-654-5876) Jigar Shah

15" x 50" Clausing Colchester #1550, 3-jaw, coolant, #8863

Sterling Machinery Exchange, South El Monte, CA 626-444-0311 (Fax 626-443-9588) Adam Mattes

15" x 50" Clausing Colchester #15, 9-1/2"SOCS,2-3/16"bore,2k RPM,in/mm,#13080

Hildebrand Machinery Co Inc, York, PA 717-846-2600 (Fax 717-845-9497) Dave Hildebrand

15" x 50" Clausing Colchester #8031VS, 10 HP, vari-speed, inch/metric, 1995

Advanced Jones Machinery Co, Dayton, OH 937-278-7337 (Fax 937-278-8234) Bob Gibson

15" x 52" LeBlond, dual dr,31-2400 RPM,taper att.,steady & follow rest,low hrs,#7560

Machinery Consultants Inc, Salt Lake City, UT 801-531-9500 (Fax 801-531-9555) Bill Wilson

15" x 54" LeBlond Regal, Servo Shift, 45-1800 RPM,taper,in/mm threads,7.5 HP,1979

Grand Marshall Machinery Inc, Hauppauge, NY 631-777-3600 (Fax 631-777-3603) Larry/ Paul

15" x 54" Leblond Makino Regal lathe, DRO, chuck, tool post, #8521

Vander Ziel Machinery Sales, Alto, MI 616-868-1111 (Fax 616-868-1115) Steve Vander Ziel

15" x 54" LeBlond Regal lathe, #9470

Vander Ziel Machinery Sales, Alto, MI 616-868-1111 (Fax 616-868-1115) Steve Vander Ziel

15" x 54" LeBlond Regal lathe, #9653

Vander Ziel Machinery Sales, Alto, MI 616-868-1111 (Fax 616-868-1115) Steve Vander Ziel

15" x 54" LeBlond Regal lathe, #9466

Vander Ziel Machinery Sales, Alto, MI 616-868-1111 (Fax 616-868-1115) Steve Vander Ziel

15" x 54" LeBlond Makino Servo Shift #1550, engine lathe,9-1/2"SOCS,10-3/4"chk,#4 MT,tailstock,inch thread,very good,#L300096

N & R Machine Sales, Navasota, TX 800-245-3194 (Fax 936-825-2679) Randy Nevels

15" x 54" LeBlond Servo Shift, inch, SR, Quick change, collet chuck, 1967

A M Metalmaq Inc, Hialeah, FL 305-883-9200 (Fax 305-883-0660) Sales Dept.

15" x 54" LeBlond Makino Servo Shift lathe, #9420

Vander Ziel Machinery Sales, Alto, MI 616-868-1111 (Fax 616-868-1115) Steve Vander Ziel

15" x 54" LeBlond Regal Servo Shift, engine lathe,45-1800 RPM,taper,10"3 & 4-jaw chucks,clean,#24680

C.W. Wood Machinery Inc, Cincinnati, OH 800-745-6008 (Fax 513-542-4819) Sales Dept.

15" x 54" LeBlond Servo Shift #15C, engine lathe, serial #6C818, #5246

IA Machinery Co, Huntington Park, CA 323-587-1887 (Fax 323-587-1811) Rick Kruger

15" x 54" LeBlond Servo Shift engine lathe, 10"3-Jaw chuck, 12"4-Jaw chuck, 15"swing, 45-1800 RPM

Gahr Machine Co Inc, Euclid, OH 216-732-3035 (Fax 216-732-3082) Bill Rhea

15" x 54" LeBlond Regal Servo Shift engine lathe, 7-1/2 HP,3&4-jaw chuck,steady rest,in/mm,taper attach.,1978,#25919

C.W. Wood Machinery Inc, Cincinnati, OH 800-745-6008 (Fax 513-542-4819) Sales Dept.

15" x 54" LeBlond Regal Servo-Shift engine lathe, 2400 RPM, chucks & tooling

Used Machinery Sales LLC, Elk River, MN 763-441-5152 (Fax 763-441-5075) John Roedel

15" x 60" Harrison #M350, in/mm threads, taper, 2-1/8"bore, 7.5 HP, 1987

Grand Marshall Machinery Inc, Hauppauge, NY 631-777-3600 (Fax 631-777-3603) Larry/ Paul

15" x 60" LeBlond Makino Regal Servo Shift, 2.5"bore,tailstock,taper attachment,1989

KGI Machine Tool, Houston, TX 713-849-9555 (Fax 713-849-9552) Kent Gasaway

15.25" x 54" Cincinnati #15-42 Tray Top lathe, 1200 RPM, 1-9/16"spindle bore, #9067

Vander Ziel Machinery Sales, Alto, MI 616-868-1111 (Fax 616-868-1115) Steve Vander Ziel

15.5" x 54" Monarch, D1-6, 3.5-900rpm,taper attach,from storage,very good,#6248

Machinery Consultants Inc, Salt Lake City, UT 801-531-9500 (Fax 801-531-9555) Bill Wilson

15.5" x 78" Monarch, D1-6, 21-900rpm,7.5hp,9.75"SOS,from storage,very good,#5247

Machinery Consultants Inc, Salt Lake City, UT 801-531-9500 (Fax 801-531-9555) Bill Wilson

16" x 30" LeBlond Regal engine lathe, 9"SOCS,3-jaw chuck,tailstock,threading,3 HP,45-1800 RPM,#11667F

Timco Inc, Columbia, TN 931-381-1900 (Fax 931-381-5151) Kris Irvin

16"/24" x 40" Goodway #GW-1640, engine lathe, 3-jaw, steady rest, tool post, #9517

Sterling Machinery Exchange, South El Monte, CA 626-444-0311 (Fax 626-443-9588) Adam Mattes

16" x 40" Sharp #1640LV, 3-1/6"hole in spdl,D1-8,3 & 4-Jaw,steady rest,Newall DRO

Technical Machine Sales Inc, Longview, TX 903-753-1955 () Craig Cave

16" x 40" Victor #1640, 1800 RPM, #3001

Turners Machinery Inc, Santa Paula, CA 805-525-2171 (Fax 805-525-5683) Al Van Wagner

16"/23" x 40" Victor #1640G, gap bed engine lathe,3-jaw chuck,brake,2"hole thru spindle,coolant,in/mm threading,#A1761

Sterling Machinery Exchange, South El Monte, CA 626-444-0311 (Fax 626-443-9588) Adam Mattes

16" x 40" Victor #1640G

Scott Machinery, McClellan, CA 916-638-7718 (Fax 916-638-2450) Deanna Payne

16"/23" x 40" Victor #1640G, 10"SOCS,3-jaw,#4MT,in/mm,steady rest,1800 RPM,#4824

IA Machinery Co, Huntington Park, CA 323-587-1887 (Fax 323-587-1811) Rick Kruger

16" x 50" Colchester Triumph #2500, excellent !, 2001

Trader Machinery Inc, Concord, ON 905-669-7507 (Fax 905-669-7512) Jon Goldman

16" x 54" American #C, geared head engine lathe, 1500 RPM, DRO, 15 HP, 1969

TNT Industrial, Huntington Beach, CA 714-612-1480 (Fax 714-242-1565) Jim Thinnsen

16" x 54" American Style C-Zip Shift, engine lathe, taper, 2-speed tailstock, zip shift, 25 HP, 1974, #147878

Machinery Values Inc, Harrison, NJ 973-497-7570 (Fax 973-497-7501) David Valitt

16" x 54" American style C engine lathe with Zip Shift

Barnett Machine Tools Inc, Mount Carmel, IL 618-375-7240 (Fax 618-375-7244) Phil Barnett

16" x 54" LeBlond, 12"3-jaw chuck, taper attachment, Steady Rest, 10 HP, #4053

F P Miller Company, Jackson, MI 517-787-3100 (Fax 517-787-3116) Craig L. Ward

16" x 54" Monarch #612, Engine Lathe, 10 HP, #4 Morse, 1960, Rebuilt 1995, #L30000103

N & R Machine Sales, Navasota, TX 800-245-3194 (Fax 936-825-2679) Randy Nevels

16" x 54" Monarch Series 50, 1800 RPM V/S,taper,10 HP,3&4-jaw,collet,1977,#8970

Turner Industries Inc, Grand Rapids, MI 616-949-5910 (Fax 616-949-3461) Jeff/Bill/David

16" x 54" Monarch, 7-1/2 HP, 3 & 4-jaw, steady, nice, 1969

Machinery Sales Company Inc, Memphis, TN 800-932-8376 (Fax 901-526-2339) D. Williams

16"/24" x 56" Enco Gap Bed, 3-Jaw chuck, 1500 RPM, universal thread, S.R., 1984

Jordan Machinery Co Inc, Greenwood, IN 317-882-1478 (Fax 317-887-1487) Jim Jordan

16" x 60" Harrison #M400, 2000 RPM, 10 HP, 10"chuck, 1977

Asset Exchange Corporation, Chicago, IL 773-866-9600 (Fax 773-866-9601) Gregg

16" x 60" LeBlond #HD, (24) speed 16-1010 RPM spdl,12"3-Jaw,10 HP,long.travel dial

Heart Of Wisconsin Mchy Co, Nekoosa, WI 715-886-4926 (Fax 715-886-3016) Fred Parker

16"/24" x 60" Profitmaster #1660, engine lathe,9"SOCS,10"3-jaw,2000 RPM,#4537

IA Machinery Co, Huntington Park, CA 323-587-1887 (Fax 323-587-1811) Rick Kruger

16" x 60" Tos #SN40C, gap lathe,23.6"in gap,2k RPM,7.5 HP,chks,in/mm,DRO,RT,clnt,'95

A Green Co Inc, Worcester, MA 508-791-6800 (Fax 508-791-6838) Harvey Green

16" x 60" Victor #1660G, 10"SOCS,3&4-jaw,#4MT,in/mm,S/R,F/R,1800 RPM,#4898

IA Machinery Co, Huntington Park, CA 323-587-1887 (Fax 323-587-1811) Rick Kruger

16" x 67" YCI Supermax #LG-1667, 2"hole,3&4-jaw,SR,gap,FP,in/mm,foot brake,clnt,RG

J Hebert Machine Tool Co., Charlotte, NC 704-825-1511 () Jon Hebert

16" x 78" Lodge & Shipley, 10-5/8"swing over cross slide,14-1160 RPM,5 HP,#14096

Harris Machine Tools, Inc., Houston, TX 713-462-5800 (Fax 713-462-8222) Sales Dept.

16" x 78" Lodge & Shipley, engine lathe,10-5/8"SOCS,taper att.,1160 RPM,1955,#53702

Yoder Machinery Sales, Holland, OH 800-622-4463 (Fax 419-865-5557) Sales

16" x 78" Monarch #610, 10 HP, 1500 RPM, taper

Monarch Lathes L.P., Sidney, OH 937-492-4111 (Fax 937-492-7958) Scott Foster

16" x 80" DoAll #16 lathe, 2-1/2"spindle bore, #9936

Vander Ziel Machinery Sales, Alto, MI 616-868-1111 (Fax 616-868-1115) Steve Vander Ziel

16" x 80" DoAll #LT16, taper attach, 4-Jaw, steady

Scott Machinery, McClellan, CA 916-638-7718 (Fax 916-638-2450) Deanna Payne

16" x 80" Harrison #M400, 10"chuck, 2.5"bore, 2000 RPM, steady, tailstock

Asset Exchange Corporation, Chicago, IL 773-866-9600 (Fax 773-866-9601) Gregg

16"/24" x 80" Summit #SNB400/2000, lathe,9-1/4"SOCS,9"3-jaw,in/mm,2000 RPM,#4536

IA Machinery Co, Huntington Park, CA 323-587-1887 (Fax 323-587-1811) Rick Kruger

16" x 80" Tos #SN40C, gap bed,22-2000 RPM,2"bore,7.5 HP,3 & 4-Jaw,DRO,'90,#9315

Turner Industries Inc, Grand Rapids, MI 616-949-5910 (Fax 616-949-3461) Jeff/Bill/David

16" x 102" American Pacemaker, 18"max.swing o/ways,Hardinge 2J speed collet chk

Naab Sales Corporation, Hopkins, MN 952-933-6755 (Fax 952-933-7229) J.Van Heuveln

16" x 120" Heyligenstaedt #400Ea/30 lathe, 3.5"spindle bore, #9129

Vander Ziel Machinery Sales, Alto, MI 616-868-1111 (Fax 616-868-1115) Steve Vander Ziel

16" x 120" LeBlond, 16-1010 RPM,13-1/2"swing cross/slide,#5 MT,taper,20hp,#18242

Yoder Machinery Sales, Holland, OH 800-622-4463 (Fax 419-865-5557) Sales

16" x 126" LeBlond #ND, engine lathe, taper, 3 & 4 Jaw Cushman, toolpost,7.5 HP,threads,25-600 RPM,#4 Morse,1949,#149011

Machinery Values Inc, Harrison, NJ 973-497-7570 (Fax 973-497-7501) David Valitt

16" x 132" LeBlond ND engine lathe, Trak 2-Axis DRO,Cushman 15"4-jaw chuck,#4MT,10 HP,taper turning attachment,1949,#149012

Machinery Values Inc, Harrison, NJ 973-497-7570 (Fax 973-497-7501) David Valitt

16.5" x 30" Monarch #14C, gap bed lathe,17-700 RPM,12"4 point chuck,15"face plate,steady rest,serial #26691,1944

GoIndustry Dovebid, Owings Mills, MD 410-654-7500 (Fax 410-654-5876) Jigar Shah

17" x 36" South Bend Turn-Nado, 1580rpm,hard,3&4-Jaw,tpr,5 collets,chk,(2)steadies,'66

Carney Machinery Co, Wilmington, DE 302-571-8382 (Fax 302-571-9538) Mike Carney

17" x 40" Clausing Colchester #8050, Engine Lathe,inch/metric,3"Hole,Trav-A-Dial,4-Jaw chk,steady,toolpost,1970's,#149394

Machinery Values Inc, Harrison, NJ 973-497-7570 (Fax 973-497-7501) David Valitt

17"/22" x 40" Graziano #SAG210N, gap bed engine lathe,3&4-jaw chuck,Duplomatic TA-80 tracer attachment,tool post,#A2153

Sterling Machinery Exchange, South El Monte, CA 626-444-0311 (Fax 626-443-9588) Adam Mattes

17"/22" x 40" Graziano #SAG210NR, gap bed engine lathe,3-jaw chuck,tool post set,tracer attachment,face plate,coolant,#A2212

Sterling Machinery Exchange, South El Monte, CA 626-444-0311 (Fax 626-443-9588) Adam Mattes

17" x 40" Howa Sangyo #1000, 12"3-jaw,tlstk,380-1500RPM,clnt,2-1/16"spdl.hole,575 V.

Cap Machinery Corp, Auburn, MA 508-832-8555 (Fax 508-832-4142) John Capuano

17" x 40" Howa Sangyo, 18.5"o/gap,6.5"face plate,9"sw.o/carriage,2-3/64"hole,#311273

Nevins Machinery Concepts Inc, Brockton, MA 508-894-0008 (Fax 508-583-1528) Jim Nevins

17" x 54" Monarch #62-1610, Buck 6-jaw chuck,less 3 jaws,4-jaw chuck,taper attachment,#9706

Sterling Machinery Exchange, South El Monte, CA 626-444-0311 (Fax 626-443-9588) Adam Mattes

17" x 60" Cadillac, 5 HP,A6 spindle,2"spindle bore,3-jaw chuck,s/n #058186

Astra Tool Co Inc, Grapevine, TX 817-481-6528 (Fax 817-421-5960) David Austin

17" x 60" Clausing Colchester #1760, 3-Jaw chuck,taper attach,7-1/2 HP,#4672

IA Machinery Co, Huntington Park, CA 323-587-1887 (Fax 323-587-1811) Rick Kruger

17" x 60" LeBlond, geared head, taper, 4-chuck, AC, Ser.#MD800

Pennsylvania Equipment Inc, Grove City, PA 724-458-6162 (Fax 724-458-0753) Tom Noone

17"/24" x 60" Mazak, in/mm threading,2"hole,10"chuck,reconditioned,#1423

Wigglesworth Machinery Co, East Boston, MA 617-567-7210 (Fax 617-561-0265) Gifford

17" x 60" Osama #SJ1760G, 2" spdl.,60-1300 RPM,7.5 HP, 3-jaw chk,tool post

Weaver Sheet Metal Inc, Ephrata, PA 717-733-4763 (Fax 717-738-3601) Daniel/David

17" x 60" South Bend Turnado, 3-Jaw & 4-Jaw chucks, threading, steady rest

Pennsylvania Equipment Inc, Grove City, PA 724-458-6162 (Fax 724-458-0753) Thomas Noone

17" x 60" South Bend Turnado #CL170G, 18"sw.o/ways,Quik change gearbox,#2754JV

Gahr Machine Co Inc, Euclid, OH 216-732-3035 (Fax 216-732-3082) Bill Rhea

17"/25" x 60" Toolmex #TUG40, 3 & 4-jaw chucks,1600 RPM,tooling,7.5 HP,1990

Raco Industrial Corp, Des Plaines, IL 847-298-8600 (Fax 847-635-8976) Jack Boecher

17" x 64" Sheldon #H17-8, lathe, 12-1/2" 3-jaw chuck, cross slide, ser. 30815, #BT5392

McKean Machinery Sales Inc, Brook Park, OH 216-761-7011 (Fax 216-761-7144) John Brand

17" x 80" Clausing Colchester #1780GH, engine lathe, S/N 7-0221-16547DD, #5434

IA Machinery Co, Huntington Park, CA 323-587-1887 (Fax 323-587-1811) Rick Kruger

17" x 80" Clausing Colchester #8000 Mascot, 28"swing in gap,2-Axis DRO,taper,3&4-jaw chucks,10 HP,steady,1968,stock #2192

Myers Technology Co LLC, Elk Grove Village, IL 847-290-0167 (Fax 847-290-0168) John Myers

17" x 80" Clausing Colchester, 2-chucks, 0-1500 RPM, Tag #14279

Yeoman Machinery Corp, Elkhart, IN 574-295-6161 (Fax 574-295-3660) Robert Yeoman

17" x 80" Clausing Colchester, 12"3-jaw,16"4-jaw,tool post,steady rest

Morris Rezman Machinery Co, Elk Grove Village, IL 312-829-2510 (Fax 312-829-1281) Jeff Rezman

17" x 80" Clausing Mascot #1600, gap bed lathe, #10056

Vander Ziel Machinery Sales, Alto, MI 616-868-1111 (Fax 616-868-1115) Steve Vander Ziel

17" x 80" Colchester, 10 HP, 20-1600 RPM, 3-1/16 HTS, 3&4 Jaw, steady, tooling, 1970s

Johnston Industrial Sales Co., Cleveland, OH 216-381-7701 (Fax 216-486-1641) C. Johnston

17" x 84" Clausing Colchester, tailstock, toolpost, 3-Jaw chuck, 10 HP, 230 V. (2)

M R S Arco Sales, Loves Park, IL 815-633-1285 (Fax 815-633-6774) Donna Richards

17" x 86" Nardini #ND-1700E lathe, #9511

Vander Ziel Machinery Sales, Alto, MI 616-868-1111 (Fax 616-868-1115) Steve Vander Ziel

17" x 100" Clausing Colchester, DRO, 12" 3-Jaw, toolpost, nice, 1986

Alenco Tool Supply, Chicago, IL 773-725-5700 (Fax 773-725-0296) Paul Braeseke

17" x 102" Monarch Series 61, engine lathe,21-900 RPM,taper attachment,(2) steady rests,12"3-jaw chuck,clean,1954,#22338

C.W. Wood Machinery Inc, Cincinnati, OH 800-745-6008 (Fax 513-542-4819) Sales Dept.

17" x 120" LeBlond Regal, 2 steady rests,follow rest,3 & 4-jaw,Trav-A-Dial,#A2016

Sterling Machinery Exchange, South El Monte, CA 626-444-0311 (Fax 626-443-9588) Adam Mattes

17" x 120" South Bend Tornado #17, 3&4 jaw,17"swing o/bed,120"cc,tpr,clnt,chip pan

HCI Machines, Venetia, PA 724-942-3382 (Fax 724-942-5194) Terry Blackman

17" x 120" South Bend, 3-jaw, inch/metric

D & D Industries Inc, Holland, OH 419-866-6894 (Fax 419-866-6801) Dave Zerbey

18" x 36" Lodge & Shipley, HD,15 HP, 10/5" SOS, D1-6, from Navy ship,great,#4197

Machinery Consultants Inc, Salt Lake City, UT 801-531-9500 (Fax 801-531-9555) Bill Wilson

18" x 40" Lodge & Shipley, well tooled,11"SOS,14-1160 RPM,5 HP,very nice,#8304

Machinery Consultants Inc, Salt Lake City, UT 801-531-9500 (Fax 801-531-9555) Bill Wilson

18" x 42" Harrison #M450, gap bed lathe, #9599

Vander Ziel Machinery Sales, Alto, MI 616-868-1111 (Fax 616-868-1115) Steve Vander Ziel

18" x 48" Lodge & Shipley #18 Blue Chip, in/mm,30-1500 RPM,3"hole,taper,DRO,12"3-jaw chuck,clean,#25884

C.W. Wood Machinery Inc, Cincinnati, OH 800-745-6008 (Fax 513-542-4819) Sales Dept.

18"/24" x 54" Dainichi #1854, engine lathe, 6-jaw chuck, steady rest, #8391

Sterling Machinery Exchange, South El Monte, CA 626-444-0311 (Fax 626-443-9588) Adam Mattes

18" x 54" LeBlond, 40-1600 RPM, taper attachment, tooling, very good, #6475

Machinery Consultants Inc, Salt Lake City, UT 801-531-9500 (Fax 801-531-9555) Bill Wilson

18" x 54" Lodge & Shipley, 4-jaw chuck, threading

Pennsylvania Equipment Inc, Grove City, PA 724-458-6162 (Fax 724-458-0753) Thomas Noone

18" x 54" Lodge & Shipley, powershft. preselect,D1-6,50-2000rpm,15HP,low hrs, #4406

Machinery Consultants Inc, Salt Lake City, UT 801-531-9500 (Fax 801-531-9555) Bill Wilson

18"/27" x 59" Hwacheon #HL460, gap bed engine lathe,Dorian qucik change tool post,chuck guard,work light,12"3-jaw,1997,#A2646

Sterling Machinery Exchange, South El Monte, CA 626-444-0311 (Fax 626-443-9588) Adam Mattes

18"/28" x 60" Clausing Colchester, 3-1/8"bore,1600 RPM,DRO,chuck,PRT,12.5 HP,2004

Raco Industrial Corp, Des Plaines, IL 847-298-8600 (Fax 847-635-8976) Jack Boecher

18" x 60" Mighty Turn lathe, 3-1/8"spindle hole,3 & 4-Jaw,Quick Change toolpost,1994

Worldwide Machine Tool, Lewis Center, OH 614-496-9414 () Bill Garbe

18" x 60" Rosenfors #RS20S, 14"4-Jaw chuck, 18.5"swing, 18-1000 RPM, 5 HP, cross slide taper attachment, S/N 408

Gahr Machine Co Inc, Euclid, OH 216-732-3035 (Fax 216-732-3082) Bill Rhea

18"/26" x 60" Sharp #1860, 10"SOCS,2-Axis DRO,3-jaw,in/mm,steady rest,2k RPM,#4862

IA Machinery Co, Huntington Park, CA 323-587-1887 (Fax 323-587-1811) Rick Kruger

18"/26" x 60" Takisawa #TAL-1500, gap bed,in/mm,9"3-jaw chuck,tool post,35-1600 RPM,clean,#24565

C.W. Wood Machinery Inc, Cincinnati, OH 800-745-6008 (Fax 513-542-4819) Sales Dept.

18" x 72" LeBlond Regal, 1500 RPM, taper, threading, 1-1/2" spdl.hole, #4615

Yoder Machinery Sales, Holland, OH 800-622-4463 (Fax 419-865-5557) Sales

18" x 72" Monarch #BB, Sony RO, 12-487 RPM, Aloris, #1594

Production Machinery Co Inc, Rockford, IL 815-962-0937 (Fax 815-962-0953) Steve Hall

18"/25" x 80" AFM Andychow #TUG40, lathe,10"SOCS,3-jaw,in/mm,1600 RPM,#4774

IA Machinery Co, Huntington Park, CA 323-587-1887 (Fax 323-587-1811) Rick Kruger

18"/25" x 80" Anderchow #Tug-40, gap type,7.5 HP,2"bore,1600RPM,12"3&4-jaw chks,'79

Industrial Resources Inc, Old Saybrook, CT 860-388-3439 (Fax 860-388-2740) Ray Magaldi

18" x 80" Clausing Colchester #8065, 12"3-Jaw,SR,taper attachment,S/N MT0035/013,'95

Machinery Solutions Inc, Lexington, SC 803-359-7000 (Fax 803-359-6464) Carl Amick

18" x 80" South Bend #22-80 EVS, gap bed lathe, #9935

Vander Ziel Machinery Sales, Alto, MI 616-868-1111 (Fax 616-868-1115) Steve Vander Ziel

18" x 114" Lodge & Shipley geared head gap bed lathe, 500 RPM,2-5/8"hole,3&4-jaw

Holt Equipment, Hopkins, MN 952-938-2202 (Fax 952-767-0840) Wayne Mader

18" x 126" LeBlond #ND, engine lathe, taper, Aloris, 4-Jaw Cushman, 10 HP, threads, #5 Morse, 18-520 RPM, 1949, #149010

Machinery Values Inc, Harrison, NJ 973-497-7570 (Fax 973-497-7501) David Valitt

18" x 138" LeBlond, 525 RPM, 1-3/4"hole, taper, steady rest, 10 HP, #14759

Harris Machine Tools, Inc., Houston, TX 713-462-5800 (Fax 713-462-8222) Sales Dept.

18" x 144" SZIM, Engine lathe, inch/metric Whitworth thread, 4-Jaw chuck

Harrison Electric Inc, Michigan City, IN 219-879-0444 (Fax 219-879-0402) Tom Walma

18.5" x 30" Axelson #16, 10"4-jaw chuck, taper attachment, Trava-dial, 1952

Shamrock Machinery Co, Houston, TX 713-699-3355 (Fax 713-699-3389) Mike Richards

18.5" x 30" Monarch lathe, 3-Jaw chuck, #7988

Vander Ziel Machinery Sales, Alto, MI 616-868-1111 (Fax 616-868-1115) Steve Vander Ziel

18.5" x 102" Axelson, 13-1577 RPM,D1-6,taper att.,chks,SR,16"face plate,low hrs,#9569

Machinery Consultants Inc, Salt Lake City, UT 801-531-9500 (Fax 801-531-9555) Bill Wilson

19" x 52" LeBlond lathe, 12"SOCS, 3 & 4-Jaw chucks, #63750

TDI Group LLC, Pittsburgh, PA 412-826-4950 (Fax 412-826-4959) D. DiBenedetto

19" x 54" LeBlond Regal, Servo Shift, 1000 RPM, DRO, chucks, located in Miami, one owner, 1966

Surplus Machine Tool, Saint Paul, MN 651-283-7444 () Dean Gabrielson

19" x 54" LeBlond Regal engine lathe, 11.5"swing over cross slide,inch threading,12"3&4-Jaw chucks,chuck guard,1962

Gahr Machine Co Inc, Euclid, OH 216-732-3035 (Fax 216-732-3082) Bill Rhea

19" x 54" LeBlond Regal engine lathe, 12"3-Jaw chuck with hard top jaws, 19.5"swing, 7.5 HP, (12) S/N 4E-640

Gahr Machine Co Inc, Euclid, OH 216-732-3035 (Fax 216-732-3082) Bill Rhea

19" x 54" LeBlond Regal, engine lathe,10"3-jaw,12"4-jaw,rear splash guard,steady rest,quick change tool holder,#A2537

Sterling Machinery Exchange, South El Monte, CA 626-444-0311 (Fax 626-443-9588) Adam Mattes

19" x 54" LeBlond Servo Shift, engine lathe, 3-jaw chuck, coolant, #9403

Sterling Machinery Exchange, South El Monte, CA 626-444-0311 (Fax 626-443-9588) Adam Mattes

19" x 54" LeBlond Regal, servo shift, hard, 1800 RPM, DRO, taper, 4-Jaw, steady, 1975

Carney Machinery Co, Wilmington, DE 302-571-8382 (Fax 302-571-9538) Mike Carney

19" x 56" American #B, 23-1500 RPM, DRO,chucks,taper attach,very low hrs,#3433

Machinery Consultants Inc, Salt Lake City, UT 801-531-9500 (Fax 801-531-9555) Bill Wilson

19" x 60" Standard Modern, in/mm threads,3-1/16"bore,20-1200 RPM,15 HP,1974

Grand Marshall Machinery Inc, Hauppauge, NY 631-777-3600 (Fax 631-777-3603) Larry/ Paul

19"/27" x 60" Summit, 4"hole, 3-Jaw, taper, 7.5 HP, 1500 RPM

Altman Machinery Co, Chicago, IL 773-247-4343 (Fax 773-247-2666) Howard /Steve

19" x 72" Cincinnati, 3 & 4-jaw, risers, coolant, 1974

Machinery Sales Company Inc, Memphis, TN 800-932-8376 (Fax 901-526-2339) D. Williams

19" x 72" Rockford, 1-1/2"bore, 804 RPM, 10"chuck (2815)

Turners Machinery Inc, Santa Paula, CA 805-525-2171 (Fax 805-525-5683) Al Van Wagner

19" x 76" LeBlond Regal, 30-1000 rpm, taper, 3 & 4 Jaw, 5-C collet chk, stdy.rest

Century Machinery Co, Los Angeles, CA 213-627-2847 (Fax 213-627-2499) Leon Dietch

19" x 78" LeBlond Regal, Servo Shift,40-1600 RPM,in/mm threads,3-1/16"bore,taper,'83

Grand Marshall Machinery Inc, Hauppauge, NY 631-777-3600 (Fax 631-777-3603) Larry/ Paul

19" x 78" LeBlond Regal lathe, #9793

Vander Ziel Machinery Sales, Alto, MI 616-868-1111 (Fax 616-868-1115) Steve Vander Ziel

19" x 78" LeBlond Regal Servo Shift, 40-1600 RPM,7-1/2 HP,12-1/2"SOCS,10"3-jaw chuck,12"4-jaw chuck,thread dial,1965,#23374

C.W. Wood Machinery Inc, Cincinnati, OH 800-745-6008 (Fax 513-542-4819) Sales Dept.

19" x 78" LeBlond, taper, 3-jaw chuck, inech/metric threading

Solomon Machinery, Eastpointe, MI 586-774-2030 (Fax 586-774-2801) Russ Solomon

19" x 78" LeBlond Regal, in/mm,3"hole,3-Jaw,steady,Aloris,10 HP,1983,#150015

Machinery Values Inc, Harrison, NJ 973-497-7570 (Fax 973-497-7501) David Valitt

19" x 80" LeBlond Regal #19, 3-jaw/4-jaw chk,face plt,Quick-Chg.toolpost Tlg,'95

Weaver Sheet Metal Inc, Ephrata, PA 717-733-4763 (Fax 717-738-3601) Daniel/David

19" x 80" Leblond Regal, Taper Attachment, Steady Rest, 12" Chuck, 1966 #9325

Gibbs Machinery Co, Warren, MI 586-755-5353 (Fax 586-755-0304) Sales Dept.

19" x 80" Standard Modern lathe, DRO, taper, 3-jaw chuck

Dominion Air & Machinery Co, Roanoke, VA 540-344-8733 (Fax 540-344-3830) Dave Gauvin

19"/29" x 80" Summit #19-4, 11"SOCS,3-jaw,#5MT,in/mm,coolant,1500 RPM,#4772

IA Machinery Co, Huntington Park, CA 323-587-1887 (Fax 323-587-1811) Rick Kruger

19"/29" x 80" Summit #19-4, 10-3/4"SOCS,3-jaw,#5MT,in/mm,coolant,1500 RPM,#4771

IA Machinery Co, Huntington Park, CA 323-587-1887 (Fax 323-587-1811) Rick Kruger

19" x 80" Summit #19-4X80, 4"spdl,3&4 jaw chks,SR & FR,4-way tool post,#015813S

Sominn Machinery Sales, Dodge Center, MN 800-770-5638 (Fax 507-374-6824) J.J. Francis

19" x 80" Wasino, 3-Jaw chuck, D6 spdl, DRO, Aloris tool post, serial #5495, 1978

Astra Tool Co Inc, Grapevine, TX 817-481-6528 (Fax 817-421-5960) David Austin

19" x 100" LeBlond Regal, taper, 1977

Belmont Machinery Co, Aurora, IL 630-844-9288 (Fax 630-844-9398) Sales

19" x 102" American Pacemaker, 1-7/8"spdl.hole,3&4 Jaw,34-2000rpm,stdy.rest,#21116

Gahr Machine Co Inc, Euclid, OH 216-732-3035 (Fax 216-732-3082) Bill Rhea

19" x 102" American, 11.5"o/slide,taper att.,18"chuck,23-1500 RPM,great,#8525

Machinery Consultants Inc, Salt Lake City, UT 801-531-9500 (Fax 801-531-9555) Bill Wilson

19" x 102" LeBlond #19" Regal Servo Shift, in/mm,#4MT,2x DRO,3&4-jaw,SR,'84,#145936

Machinery Values Inc, Harrison, NJ 973-497-7570 (Fax 973-497-7501) David Valitt

19"/27" x 120" Summit #19-4, engine lathe, serial #U73407949, #4771

IA Machinery Co, Huntington Park, CA 323-587-1887 (Fax 323-587-1811) Rick Kruger

19" x 126" LeBlond Regal, 12.25"SOCS,6"steady rest,15 HP,coolant,1973,#13607

Yoder Machinery Sales, Holland, OH 800-622-4463 (Fax 419-865-5557) Sales

19" x 150" LeBlond Makino, 15" 4-Jaw chuck threading, taper attachment

Pennsylvania Equipment Inc, Grove City, PA 724-458-6162 (Fax 724-458-0753) Thomas Noone

19" x 150" Leblond, 3-jaw,3 steady rests,ways ground & slides scrapped,#UD100003

Machinery Solutions Inc, Lexington, SC 803-359-7000 (Fax 803-359-6464) Carl Amick

19" x 150" LeBlond Regal, 25-1000 RPM, taper attach, well tooled, 5 HP, good, #5453

Machinery Consultants Inc, Salt Lake City, UT 801-531-9500 (Fax 801-531-9555) Bill Wilson

19" x 154" LeBlond Makino Regal, in/mm,56-1600rpm,3"spdl.hole,10 HP,turret attach,DRO

Century Machinery Co, Los Angeles, CA 213-627-2847 (Fax 213-627-2499) Leon Dietch

19" x 154" Leblond Regal Servo, 1600 RPM, 7-1/2 HP, threading dial, #4MT, 1989, #2904

Gahr Machine Co Inc, Euclid, OH 216-732-3035 (Fax 216-732-3082) Bill Rhea

19" x 180" LeBlond #19" Regal, engine lathe,12"3-jaw,15"4-jaw,5 HP,(3) steady rests,follow rest,collant system,1957,#25768

C.W. Wood Machinery Inc, Cincinnati, OH 800-745-6008 (Fax 513-542-4819) Sales Dept.

19.5" x 56" American #B, D1-6,23-1500 RPM,15 HP,DRO,well tooled,low hrs,great,#3433

Machinery Consultants Inc, Salt Lake City, UT 801-531-9500 (Fax 801-531-9555) Bill Wilson

19.68" x 98.42" VDF, heavy duty lathe, #3084

DiPaolo Machine Tools, Mississauga, ON 905-676-9265 (Fax 905-676-9436) Nelson Martins

20" x 30" American #B, heavy duty,20"sw.o/ways,10.5"o/cr.sl,30"btwn,stock #9778

Yoder Machinery Sales, Holland, OH 800-622-4463 (Fax 419-865-5557) Sales

20" x 30" Lodge & Shipley lathe, steady rest,15-3/4"3-jaw chuck,24"4-jaw chuck,1946

Fahey Machinery Co Inc, Lake Oswego, OR 503-620-9031 (Fax 503-620-1911) William Fahey,Jr.

20" x 40" American #B2030, 30-2000 RPM,10 HP,#3MT,3 & 4-Jaw chk,steady,#4745

IA Machinery Co, Huntington Park, CA 323-587-1887 (Fax 323-587-1811) Rick Kruger

20" x 48" Lodge & Shipley #16-20, engine lathe

Equipment Resale Inc, Fort Wayne, IN 800-733-9474 (Fax 260-422-5955) Isaac Jimenez

20" x 54" Lodge & Shipley #AVS2013, Geared Head Engine Lathe, 1965

Asset Exchange Corporation, Chicago, IL 773-866-9600 (Fax 773-866-9601) Gregg

20" x 54" L & S #AVS2013.Vari-spd.dr, 16" 3-jaw chk,tpr.att,25-1500rpm,15HP,1966

Weaver Sheet Metal Inc, Ephrata, PA 717-733-4763 (Fax 717-738-3601) Daniel/David

20" x 54" Monarch #2013, 13"SOCS,12-1500 RPM,12"3-jaw chuck,taper attachment,nice,1969,#25954

C.W. Wood Machinery Inc, Cincinnati, OH 800-745-6008 (Fax 513-542-4819) Sales Dept.

20" x 54" Monarch #610, engine lathe,roller type steady rest,15 HP,thrds,1993,#150046

Machinery Values Inc, Harrison, NJ 973-497-7570 (Fax 973-497-7501) David Valitt

20" x 54" Monarch #610, engine lathe, #4MT, 15 HP, Ser.#4709R, 1993, #3900

Abbott Machine Co, Alton, IL 800-262-6478 (Fax 618-465-2495) Mike St. Peters

20" x 60" Daewoo #A20, in/mm, 18-2000 RPM, 3.03" Spindle Hole, 10 HP, Tooling

Century Machinery Co, Los Angeles, CA 213-627-2847 (Fax 213-627-2499) Leon Dietch

20" x 60" Daewoo #DST20, engine lathe, 3"bore

Technical Machine Sales Inc, Longview, TX 903-753-1955 () Craig Cave

20" x 60" LeBlond #NE, 16-1010 RPM, 10 HP, chks, from storage, xlnt, #3513

Machinery Consultants Inc, Salt Lake City, UT 801-531-9500 (Fax 801-531-9555) Bill Wilson

20" x 60" Lion, 11-1/2"OCS,3.2"hole,to 2000 RPM,taper,in/mm,steady rest,12.5 HP

Universal Metalworking Equip., Houston, TX 713-675-4145 (Fax 713-675-1294) M. Feinstein

20" x 60" Lodge & Shipley Heavy Duty Micrometer, 25 HP,carriage stop,chucks,S/R,#14970

Raco Industrial Corp, Des Plaines, IL 847-298-8600 (Fax 847-635-8976) Jack Boecher

20" x 60" Lodge & Shipley, 24-2000 RPM, 20 HP, taper att., very limited use, #9495

Machinery Consultants Inc, Salt Lake City, UT 801-531-9500 (Fax 801-531-9555) Bill Wilson

20" x 60" Meuser #2060, 3-Jaw chk,tlpst,one shot lube sys,28-1250rpm,10hp,#4671

IA Machinery Co, Huntington Park, CA 323-587-1887 (Fax 323-587-1811) Rick Kruger

20" x 60" Powerturn, 12"3-Jaw chuck, Fagor 2-Axis DRO, 2007

Trader Machinery Inc, Concord, ON 905-669-7507 (Fax 905-669-7512) Jon Goldman

20" x 60" Standard Modern #2060, in/mm,27-1600 RPM,3&4-jaw chucks,3"hole,taper,DRO,well tooled,nice,#25953

C.W. Wood Machinery Inc, Cincinnati, OH 800-745-6008 (Fax 513-542-4819) Sales Dept.

20" x 64" Bridgeport Romi Tormax #20-10, 3-jaw,4-way tl post,follow rest,clnt,v/good

Action Machinery Inc, Louisville, KY 502-459-1313 (Fax 502-473-1953) Thomas Cheney

20" x 78" American, 11.5"swing o/CS,18 speed 25-1500 RPM,14"4-jaw,10 HP,#16440

Yoder Machinery Sales, Holland, OH 800-622-4463 (Fax 419-865-5557) Sales

20" x 78" Daewoo #DST20, engine lathe, 3"bore

Technical Machine Sales Inc, Longview, TX 903-753-1955 () Craig Cave

20" x 78" LeBlond, 20-1/2"swing o/bed,13-1/2"swing OCS,16-1010 RPM,#17676

Yoder Machinery Sales, Holland, OH 800-622-4463 (Fax 419-865-5557) Sales

20" x 78" Monarch #613, Engine Lathe, 10 HP, 12-1500 RPM, Ser.#52022, 1978, #L3000126

N & R Machine Sales, Navasota, TX 800-245-3194 (Fax 936-825-2679) Randy Nevels

20" x 78" Monarch lathe, 1-3/4"spindle bore, 17-700 RPM, #5322

Vander Ziel Machinery Sales, Alto, MI 616-868-1111 (Fax 616-868-1115) Steve Vander Ziel

20" x 80" Monarch Series 614, mdl 2013,Heidenhain DRO,chuck,steady,tool post,1995

Wigglesworth Machinery Co, East Boston, MA 617-567-7210 (Fax 617-561-0265) Gifford

20" x 80" Sirco lathe, 1975

T R Wigglesworth Machinery, Bedford, OH 440-232-6660 (Fax 440-232-5541) T. Wigglesworth

20" x 80" Summit, 12"3-Jaw chk,4"hole,steady rest,taper attachment,tool post,S31565

Perfection Industrial Sales, Elk Grove Village, IL 866-314-4971 (Fax 847-427-8884) Dept. Sales

20" x 80" Tos #SN50C, gap bed,22-2000 RPM,inch/metric,10 HP,1999,#12157

Hildebrand Machinery Co Inc, York, PA 717-846-2600 (Fax 717-845-9497) Dave Hildebrand

20" x 80" Tos Trencin #SN40A-50A, 10"SOCS,28"sw.o/gap,1.93"nose,#MT5,tlstk,#4050

Jorgenson Machine Tools, Salt Lake City, UT 801-493-0151 (Fax 801-493-0157) Kyle Jorgenson

20" x 80" Tos Trencin #SUI50, Engine Lathe, 2240 RPM, 12" 4-Jaw Chuck, Ser.#3950, #L3000130

N & R Machine Sales, Navasota, TX 800-245-3194 (Fax 936-825-2679) Randy Nevels

20"/29" x 80" Wacheon #HL-520, gap bed,28-1350 RPM,in/mm,3"hole,steady rest,3&4-jaw chucks,10 HP,1986,#25880

C.W. Wood Machinery Inc, Cincinnati, OH 800-745-6008 (Fax 513-542-4819) Sales Dept.

20" x 100" Victor #S20100G, gap bed,31-1500 RPM,inch/metric,10 HP,#12159

Hildebrand Machinery Co Inc, York, PA 717-846-2600 (Fax 717-845-9497) Dave Hildebrand

20" x 108" American, 25 HP, 12"3-jaw, 2 SR, Aloris TP, coolant (no tailstock), #1187

Production Machinery Co Inc, Rockford, IL 815-962-0937 (Fax 815-962-0953) Steve Hall

20"/27.5" x 116" Victor #20120G, gap type,3 & 4-Jaw chucks,in/mm threading,2"hole thru spdl,#26405

Mohawk Machinery Inc, Cincinnati, OH 513-771-1952 (Fax 513-771-5120) Mr.Secord

20" x 120" Lansing #G20, removable gap to 28",in/mm threads,4-1/8"bore,10 HP,1975

Grand Marshall Machinery Inc, Hauppauge, NY 631-777-3600 (Fax 631-777-3603) Larry/ Paul

20" x 120" Monarch #613, inch/metric, taper, 1980

Belmont Machinery Co, Aurora, IL 630-844-9288 (Fax 630-844-9398) Sales

20"/27" x 120" Monarch, 3 & 4 Jaw chks,Steady rest,Thrdg,20 HP,1961,#149566

Machinery Values Inc, Harrison, NJ 973-497-7570 (Fax 973-497-7501) David Valitt

20" x 120" Nardini #IN20120T, gap bed engine lathe,20"3-jaw chuck,in/mm,steady & follow rest,2-Axis DRO,1997,#13136T

Timco Inc, Columbia, TN 931-381-1900 (Fax 931-381-5151) Kris Irvin

20" x 120" Polamco #TUR-50, in/mm,#5MT,10"3-jaw,SR,toolpost,15 HP,tlstk,'78,#149638

Machinery Values Inc, Harrison, NJ 973-497-7570 (Fax 973-497-7501) David Valitt

20" x 126" Monarch, 15 HP, 18"4-jaw chuck, taper, 1980

Scott Machinery & Supply Inc, Helena, AL 205-664-9644 (Fax 205-664-9796) George Scott

20"/25" x 144" American Pacemaker, taper attach,4-Jaw,(5) steady rests,hard ways,2.5"spindle hole,18-800 RPM,#5MT,#26673

Mohawk Machinery Inc, Cincinnati, OH 513-771-1952 (Fax 513-771-5120) Mr.Secord

20" x 174" American Pacemaker Style D 20X174, 20 HP, Ser.#79340-73, 1973, #L30009

N & R Machine Sales, Navasota, TX 800-245-3194 (Fax 936-825-2679) Randy Nevels

20" x 180" Lodge & Shipley, Lathe, 2-1/2" hole, #6950

Vander Ziel Machinery Sales, Alto, MI 616-868-1111 (Fax 616-868-1115) Steve Vander Ziel

20.5" x 30" Lodge & Shipley #2013, 13.5"OCS,5-1160 RPM,18"4-jaw,T/P,thrd dial,'68

Norman Machine Tool Ltd, Baltimore, MD 410-633-2300 (Fax 410-633-7737) Mike Norman

20-1/2" x 48" Monarch engine lathe, 3&4-jaw chucks, steady rest, threading dial,13-550 RPM,7-1/2 HP,1941,#17125

Raco Industrial Corp, Des Plaines, IL 847-298-8600 (Fax 847-635-8976) Jack Boecher

20-1/2" x 58" Sebastian, engine lathe, 1-1/2"hole thru spindle,15-479 RPM,standard threading,9"3-Jaw chuck,5 HP

Hoff Online Auctions, Minneapolis, MN 612-521-5500 (Fax 612-331-3291) Denny Hoff

20-1/2" x 60" Webb, 12"4-jaw,tpr,Quick change tlg,live center,drill chuck,6"SR,#4354

Diamond Jack Machinery Inc, Fort Smith, AR 479-785-2554 (Fax 479-785-4362) Jack Yancey

21" x 36" Lodge & Shipley, engine lathe, 14-1160 RPM, standard threading, 12"3-Jaw chuck, 16"face plate, steady rest

Hoff Online Auctions, Minneapolis, MN 612-521-5500 (Fax 612-331-3291) Denny Hoff

21" x 50" Cazeneuve #HB575, in/mm,25-2000 RPM,2"spindle hole,9 KW,tooling

Century Machinery Co, Los Angeles, CA 213-627-2847 (Fax 213-627-2499) Leon Dietch

21" x 51" Dainichi #L3000, 12"SOCS,32"sw.o/gap,A1-8,in/mm,#MT5,20-1000rpm,#4052

Jorgenson Machine Tools, Salt Lake City, UT 801-493-0151 (Fax 801-493-0157) Kyle Jorgenson

21" x 51" Okuma #LS540, 12" 3-Jaw chuck, tailstock, steady rest

Lee Stevens Machinery Inc., Wixom, MI 248-926-8400 (Fax 248-926-8499) Randy/ Jeff/Chris

21" x 54" Lodge & Shipley #AVS-2013, variator drive,3 Jaw,taper attach.,clnt,#9223

Sterling Machinery Exchange, South El Monte, CA 626-444-0311 (Fax 626-443-9588) Adam Mattes

21" x 60" Mighty-Turn #ML2160GL, 4-jaw,steady rest,taper,4 way rapid,15 HP,1990,#6100

Sterling Machinery Exchange, South El Monte, CA 626-444-0311 (Fax 626-443-9588) Adam Mattes

21" x 60" Okuma #LS540, engine lathe,4-jaw chuck,taper attachment,steady rest,tool post,#A1369

Sterling Machinery Exchange, South El Monte, CA 626-444-0311 (Fax 626-443-9588) Adam Mattes

21" x 60" Okuma #LS-540, lathe,13.7"SOCS,12"3-jaw,#4MT,in/mm,1800 RPM,#4909

IA Machinery Co, Huntington Park, CA 323-587-1887 (Fax 323-587-1811) Rick Kruger

21" x 72" Clausing Colchester #2180GH, engine lathe, serial #8-0222-0594, #4681

IA Machinery Co, Huntington Park, CA 323-587-1887 (Fax 323-587-1811) Rick Kruger

21"/40" x 72" H. Ernault #Jupiter 830R, heavy duty,3"spdl.bore,25 HP,4 jaw chuck,cnlt,'81

Cities Advanced Machinery, Eden Prairie, MN 952-944-6060 (Fax 952-944-0043) Harry Youtsos

21" x 78" Lodge & Shipley #2013AVS, 1500 RPM, 15 HP, #5MT, 1968, #2453

Gahr Machine Co Inc, Euclid, OH 216-732-3035 (Fax 216-732-3082) Bill Rhea

21" x 80" American Style C 1678, 2-axis tracer attachment,3&4-jaw steady rest,#9610

Sterling Machinery Exchange, South El Monte, CA 626-444-0311 (Fax 626-443-9588) Adam Mattes

21" x 80" Clausing Colchester #2172, 18-1400 RPM, 12.5 HP, steady rest, #4681

IA Machinery Co, Huntington Park, CA 323-587-1887 (Fax 323-587-1811) Rick Kruger

21" x 80" Clausing Colchester, 18-1400 RPM,3"hole,DRO,3&4-Jaw chks,8"steady rest,tpr

Richard Lunt Machinery, Seattle, WA 206-484-8585 (Fax 206-767-9825) Richard Lunt

21" x 80" Clausing Colchester, 15" 3-Jaw chuck, 3.5" hole thru, 4-way rapids, 1997

Alenco Tool Supply, Chicago, IL 773-725-5700 (Fax 773-725-0296) Paul Braeseke

21" x 80" Lodge & Shipley Powerturn, D1-6,21-1740 RPM,taper att.,exceptional,#7254

Machinery Consultants Inc, Salt Lake City, UT 801-531-9500 (Fax 801-531-9555) Bill Wilson

21" x 80" Mighty Turn, 3-1/4"hole,15 HP,rapid traverse,3 & 4-Jaw,rear guard,good,'92

J Hebert Machine Tool Co., Charlotte, NC 704-825-1511 () Jon Hebert

21"/29" x 80" Webb #20-1/2x80, gap bed engine lathe,3&4-jaw chuck,steady & follow rest,4 way tool post,coolant sys,'79,#A2172

Sterling Machinery Exchange, South El Monte, CA 626-444-0311 (Fax 626-443-9588) Adam Mattes

21" x 84" Lodge & Shipley, taper attach,15"chk,S/R,3"bore,1740 RPM,Trav-a-dial,super

JMC Machinery Sales Inc, Warren, MI 586-756-8855 (Fax 586-756-8866) J. Simonetta

21" x 96" LeBlond Regal, 3 & 4-Jaw chuck, hard ways, nice

Michael Fine Machinery Co., Livingston, NJ 973-992-5961 (Fax 973-992-8334) Michael/ Dave

21" x 102" LeBlond #1610HD, 2660 RPM, 3 & 4 Jaw, SR, taper, 1962

Heart Of Wisconsin Mchy Co, Nekoosa, WI 715-886-4926 (Fax 715-886-3016) Fred Parker

21" x 104" Tarnow #TUJ48x2500, 1120 RPM,2-1/8"hole,in/mm,2000 RPM,3 chucks

Holt Equipment, Hopkins, MN 952-938-2202 (Fax 952-767-0840) Wayne Mader

21" x 120" Clausing lathe, 12"3-jaw chuck, Travadial steady rest, coolant

Dominion Air & Machinery Co, Roanoke, VA 540-344-8733 (Fax 540-344-3830) Dave Gauvin

21"/33" x 120" Clausing Colchester, in/mm,18-1400rpm,3-1/2"spdl.hole,DRO,taper,tlg

Century Machinery Co, Los Angeles, CA 213-627-2847 (Fax 213-627-2499) Leon Dietch

21"/28" x 120" Kingston #HL3000, chuck,taper,1500 RPM,3-1/8"bore,DRO,10 HP,1981

Raco Industrial Corp, Des Plaines, IL 847-298-8600 (Fax 847-635-8976) Jack Boecher

21" x 126" Cincinnati, 21-1/2"x 120"tray-top,12"chuck,tailstock,steady,tool post

Asset Exchange Corporation, Chicago, IL 773-866-9600 (Fax 773-866-9601) Gregg

21" x 126" Polamco #TUR50, 18-1800 RPM, 2-7/8" spindle, 1977

Wheeler Machinery Sales, Huntington Park, CA 888-589-6721 (Fax 323-589-6199) Dan Wheeler

21" x 144" Dean Smith & Grace, 3-jaw univ.chuck, 4-jaw combination chuck, taper

J Hebert Machine Tool Co., Charlotte, NC 704-825-1511 () Jon Hebert

21.5" x 36" American #C, HD, 20 HP, 23-1500 RPM, exc, from storage, #9019

Machinery Consultants Inc, Salt Lake City, UT 801-531-9500 (Fax 801-531-9555) Bill Wilson

21.5" x 72" Cincinnati, 21-1/2"tray top,21-1/2"sw.o/bed,72"btwn,stock #15618

Yoder Machinery Sales, Holland, OH 800-622-4463 (Fax 419-865-5557) Sales

22" x 40" Ecoca, 15 HP, 6-Jaw chuck, inch/metric threading, 2002, #4090

F P Miller Company, Jackson, MI 517-787-3100 (Fax 517-787-3116) Craig L. Ward

22" x 48" Axelson, 14.5" SOS, D1-8, 20 HP, taper att., very good, #7317

Machinery Consultants Inc, Salt Lake City, UT 801-531-9500 (Fax 801-531-9555) Bill Wilson

22" x 50" L & S #AUS2013, 14"SOCSA,2"hole,34-2000rpm,s/n #50796,stk.#3996C

Jorgenson Machine Tools, Salt Lake City, UT 801-493-0151 (Fax 801-493-0157) Kyle Jorgenson

22" x 52" Okuma #L-S, S31597

Perfection Industrial Sales, Elk Grove Village, IL 866-314-4971 (Fax 847-427-8884) Dept. Sales

22" x 54" L & S, 14" swg.cr/sld, 2000 RPM, taper, chuck, threading, 1965, #3399

Yoder Machinery Sales, Holland, OH 800-622-4463 (Fax 419-865-5557) Sales

22" x 60" Cazeneuve #HB575, 3 & 4-jaw,SR,coolant,4 WTP,WL,TD,tracer,12 HP,#6002

A M Metalmaq Inc, Hialeah, FL 305-883-9200 (Fax 305-883-0660) Sales Dept.

22" x 71" Cincinnati Hydra-Shift, 3-Jaw, steady rest, 2-5/16"hole

Altman Machinery Co, Chicago, IL 773-247-4343 (Fax 773-247-2666) Howard /Steve

22" x 72" Lodge & Shipley Blue Chip 21 lathe, 20-1000 RPM, 3-jaw, taper attach

Scott Machinery & Supply Inc, Helena, AL 205-664-9644 (Fax 205-664-9796) George Scott

22" x 80" Graziano Sag #22, 3-jaw,quick change tool post set,Trav-a-Dial,clnt,#A2066

Sterling Machinery Exchange, South El Monte, CA 626-444-0311 (Fax 626-443-9588) Adam Mattes

22" x 80" Tos #SN55 IMC, 18"4-Jaw chuck, 22.5"swing, 10-1000 RPM, S/N 0412487

Gahr Machine Co Inc, Euclid, OH 216-732-3035 (Fax 216-732-3082) Bill Rhea

22" x 84" Supermaster, 22"sw.o/ways/10.5"OCS,84"btwn,16-1250 RPM,stock #8768

Yoder Machinery Sales, Holland, OH 800-622-4463 (Fax 419-865-5557) Sales

22"/30" x 90" Yang gap bed engine lathe, 4 way tool post,steady rest,Jacobs 18N,Rohm 10"3-jaw scroll chuck,foot brake,#A2655

Sterling Machinery Exchange, South El Monte, CA 626-444-0311 (Fax 626-443-9588) Adam Mattes

22" x 108" LeBlond, 38-1080 RPM, 14"over slide, 2-112 TPI, 2-1/4"hole,#6162

Yoder Machinery Sales, Holland, OH 800-622-4463 (Fax 419-865-5557) Sales

22" x 120" Boye & Emmes, 12.5-436 RPM,2-1/32"spindle hole,10 HP,taper,s/r,#13997

Harris Machine Tools, Inc., Houston, TX 713-462-5800 (Fax 713-462-8222) Sales Dept.

22" x 120" Supermax #LG-22120, 31"in gap,in/mm threading,1200 RPM,1994,#19834

Prestige Equipment Corp, Melville, NY 631-249-5566 (Fax 631-249-9494) Terry Lashin

22"/31" x 120" Tarnow #TUJ-50, gap,in/mm,20-1600 RPM,15 HP,12"3-jaw chuck,coolant,hardened & ground bedways,clean,1977,#25922

C.W. Wood Machinery Inc, Cincinnati, OH 800-745-6008 (Fax 513-542-4819) Sales Dept.

Victor- 22" x 120" engine lathe- 4" spindle hole- 15 hp- excellent - new 2008

Linden Machine Tools, Natick, MA 508-728-2288 (Fax 508-653-1767) Mike Zirlen

22" x 14' LeBlond, lathe,18"4-jaw chuck,2"hole in spindle,4 way,6"SR,10 HP,#4330

Diamond Jack Machinery Inc, Fort Smith, AR 479-785-2554 (Fax 479-785-4362) Jack Yancey

23" x 72" Axelson, 13"SOS,D1-8,20HP,9-961RPM,pwr.rapid X,taper att,very nice,#7557

Machinery Consultants Inc, Salt Lake City, UT 801-531-9500 (Fax 801-531-9555) Bill Wilson

23" x 102" Demoor engine lathe (3596)

Turners Machinery Inc, Santa Paula, CA 805-525-2171 (Fax 805-525-5683) Al Van Wagner

23" x 108" Lodge & Shipley #20, 9-500 RPM,18"chk,taper att,stdy.rest,very good,#6524

Machinery Consultants Inc, Salt Lake City, UT 801-531-9500 (Fax 801-531-9555) Bill Wilson

23" x 120" Weisser Heilbron, 15-1/2"o/cross slide,21"gap,15 HP,900 RPM,2-1/2"spdl bore,20"4-jaw chk,taper

Modern Tool Ltd, Calgary, AB 403-236-1150 (Fax 403-236-4277) Mark Senecal

23" x 132" Springfield #280, engine lathe, serial #57071, #13857

Yoder Machinery Sales, Holland, OH 800-622-4463 (Fax 419-865-5557) Sales

23" x 160" Summit #23-4-160, taper, chuck, PRT, 1981

Raco Industrial Corp, Des Plaines, IL 847-298-8600 (Fax 847-635-8976) Jack Boecher

23.5" x 157" Timemaster (Gurutzpe), 34"sw.in gap,in/mm thrds, 2-3/16"bore,15 HP,'77

Grand Marshall Machinery Inc, Hauppauge, NY 631-777-3600 (Fax 631-777-3603) Larry/ Paul

24" x 48" LeBlond Regal 3J & 4J, taper, Trak DRO, coolant, rear guard, 1972

J Hebert Machine Tool Co., Charlotte, NC 704-825-1511 () Jon Hebert

24" x 50" Monarch, MM only,15" SOS,9-400 RPM,21" 4-Jaw,steady rest,very good,#4478

Machinery Consultants Inc, Salt Lake City, UT 801-531-9500 (Fax 801-531-9555) Bill Wilson

24" x 60" LeBlond Servo Shift, 3"spindle bore,threading,taper attach.,coolant,1994

Liberty Machinery Co, Lincolnshire, IL 847-276-2761 (Fax 847-276-2762) Peter Sonneborn

24" x 70" LeBlond Regal, 5"thru spindle engine lathe,21"4-Jaw & 16"3-Jaw chks,#1753

Charleston Annex Corporation, Indian Trail, NC 704-821-7370 (Fax 704-821-7392) Lance/ Mark

24" x 72" Monarch #20, engine lathe, 1.5"spindle bore, 30 HP, 1953, #L300038

N & R Machine Sales, Navasota, TX 800-245-3194 (Fax 936-825-2679) Randy Nevels

24" x 72" Sidney, engine lathe, 2.75"spindle bore, 15 HP, 1954, #L300029

N & R Machine Sales, Navasota, TX 800-245-3194 (Fax 936-825-2679) Randy Nevels

24" x 78" Monarch, (16) 24-1000 RPM,1.5"spdl.hole,8"3-jaw chk,clnt,SR,1953,#5155

Yoder Machinery Sales, Holland, OH 800-622-4463 (Fax 419-865-5557) Sales

24" x 80" Mazak, 4-1/16"hole,14-1/2"OCS,to 1200 RPM,taper,coolant,(2) SR,18"4-jaw

Universal Metalworking Equip., Houston, TX 713-675-4145 (Fax 713-675-1294) M. Feinstein

24" x 80" Tos #B63, 16"SOCS,3"spdl.hole,18"3-jaw,#5MT,in/mm,10-1k RPM,#L300098

N & R Machine Sales, Navasota, TX 800-245-3194 (Fax 936-825-2679) Randy Nevels

24" x 100" LeBlond, 14"SOS,18"4-jaw,9-800 RPM,L-2,20 HP,steady rests,low hrs,#5570

Machinery Consultants Inc, Salt Lake City, UT 801-531-9500 (Fax 801-531-9555) Bill Wilson

24" x 102" Monarch #612, 1500 RPM, 20 HP, 2 sp tail, leadscrew reverse, 1967

Monarch Lathes L.P., Sidney, OH 937-492-4111 (Fax 937-492-7958) Scott Foster

24" x 120" American, 28" actual swing, 4-jaw chuck, taper attachment

Mauldin Machine Inc, Jacksonville, AR 501-835-5494 (Fax 501-982-0200) Jerry Mauldin

24" x 120" Mazak Hercules Ajax #24, 1540 RPM, 1974

Scott Machinery & Supply Inc, Helena, AL 205-664-9644 (Fax 205-664-9796) George Scott

24"/31" x 120" Morando #PA-24, lathe,16-1/2"SOCS,3-jaw,#5MT,in/mm,2k RPM,#4773

IA Machinery Co, Huntington Park, CA 323-587-1887 (Fax 323-587-1811) Rick Kruger

24" x 120" Pasquino Milano, 3-jaw chk,2.5"hole,#5MT,clnt,in/mm,toolpost,1960's,#145475

Machinery Values Inc, Harrison, NJ 973-497-7570 (Fax 973-497-7501) David Valitt

24" x 120" Summit #120B, manual engine lathe, #3610

Turners Machinery Inc, Santa Paula, CA 805-525-2171 (Fax 805-525-5683) Al Van Wagner

24" x 120" Summit #24B, 2-Axis Accurite DRO, 4"bar capacity, 12.5-1250 RPM, 2007

Seminole Machinery Company, Clinton Township, MI 586-465-9700 (Fax 586-465-6226) Dan Patrona

24" x 120" Summit, taper attachment,steady rest,3"spdl.bore,19"4-Jaw chuck,1980's

Harvey Machine Tool Co, Tulsa, OK 918-663-0604 (Fax 918-663-0704) Henry Harvey

24" x 120" Tos, geared hd precision,heavy duty,8-1180 RPM,steady rest,4-jaw chk

Pearl Equipment Co, Nashville, TN 615-383-8703 (Fax 615-297-3463) Si Culp

24" x 132" Sidney #20, Engine Lathe, 18" 4 Jaw chuck, 1000 RPM, Ser.#9515, #L3000135

N & R Machine Sales, Navasota, TX 800-245-3194 (Fax 936-825-2679) Randy Nevels

24" x 12' LeBlond Regal, 5-1/4" hole, 18"3-jaw chuck, steady, T.S., 10 HP, 1965

Hesco Equipment Sales Co Inc, Houston, TX 713-699-4766 (Fax 713-699-8986) Bob Hess

24" x 144" LeBlond Regal engine lathe, 5"spindle bore, 15-350 RPM, #8263

Vander Ziel Machinery Sales, Alto, MI 616-868-1111 (Fax 616-868-1115) Steve Vander Ziel

24" x 144" Leblond, Servo-Shift, inch/metric, 3" hole, 1600 RPM, taper

Hardy Machinery Inc, Huntsville, AL 256-536-1319 (Fax 256-536-1322) Ron Hardy

24" x 168" Meuser #24x168, 27 spdl.spds,3/32-64 TPI,2.5"spdl.hole,12"3-jaw,#3327

Yoder Machinery Sales, Holland, OH 800-622-4463 (Fax 419-865-5557) Sales

24" x 168" Monarch 2CM, 21" chuck, 15 hp, steady, toolpost,

Asset Exchange Corporation, Chicago, IL 773-866-9600 (Fax 773-866-9601) Gregg

24" x 192" Axelson #E, 3-4 jaw chks,tpr,stdy,2-3/8"spdl.bore,face plate,inch thrdg

Strand Industrial Machinery, Hamel, MN 763-478-0306 (Fax 763-478-0307) Dan Strand

24" x 192" LeBlond Regal, 720 RPM, 7-1/2 HP, 4-jaw chuck, 1967/1968, #2929JV

Gahr Machine Co Inc, Euclid, OH 216-732-3035 (Fax 216-732-3082) Bill Rhea

24" x 192" LeBlond, 18"over cross slide, Servo Shift, Sony DRO, 1963

O'Connell Machinery Co, Buffalo, NY 716-877-3666 (Fax 716-877-1136) W. O'Connell

24" x 16' Swift, 3.5"hole, 1960

Belmont Machinery Co, Aurora, IL 630-844-9288 (Fax 630-844-9398) Sales

24.41" x 124" Clausing Metosa #C24124SS, 24"gap lathe, 2001

Kaste Industrial Machine Sale, Enfield, CT 860-623-5700 (Fax 860-654-0548) Brad

24-1/2" x 192" Monarch #18CBB lathe, 700 RPM, 16 speeds, #8812

Vander Ziel Machinery Sales, Alto, MI 616-868-1111 (Fax 616-868-1115) Steve Vander Ziel

25" x 60" Nardini #-2560, Inch/Metric Threading, Acu-Rite 2-Axis DRO, new 2001

Advanced Jones Machinery Co, Dayton, OH 937-278-7337 (Fax 937-278-8234) Bob Gibson

25" x 72" Monarch #612, 1500 RPM,25 HP,tailstock,coolant system & chip pan

Monarch Lathes L.P., Sidney, OH 937-492-4111 (Fax 937-492-7958) Scott Foster

25" x 78" DMTG #CW6263E, (2) chucks,digitial readouts,taper attachment,2011,#20046

Prestige Equipment Corp, Melville, NY 631-249-5566 (Fax 631-249-9494) Terry Lashin

25"/36" x 80" Clausing Colchester #25", engine lathe, serial #MG0073, 1998, #5738

IA Machinery Co, Huntington Park, CA 323-587-1887 (Fax 323-587-1811) Rick Kruger

25" x 80" Polamco Wafum #TUR63A, 14-1/2"SOCS,3-jaw,#5MT,1120 RPM,1981,#4770

IA Machinery Co, Huntington Park, CA 323-587-1887 (Fax 323-587-1811) Rick Kruger

25" x 80" Polamco Wafum #TUR63A/80, 14-1/2"SOCS,3-jaw,#5MT,1120 RPM,#4670

IA Machinery Co, Huntington Park, CA 323-587-1887 (Fax 323-587-1811) Rick Kruger

25"/16" x 90" LeBlond #2516NF, 16"OCS, 2-1/4"hole, to 1300 RPM, 30 HP, 1968

Universal Metalworking Equip., Houston, TX 713-675-4145 (Fax 713-675-1294) M. Feinstein

25" x 118" Dainichi, 18" 3-Jaw Chuck, 35" Gap, 15" OV.CS,inch/metric,#2916

Standard Industrial Machinery, Oxford, AL 256-831-1211 (Fax 256-831-2207) W Robert O'Neal

25" x 118" Toolmex Haco #TUR630A, 5.5"bore,Oil country,17"Tri-V,European,new

Toolmex Corp, Schaumburg, IL 847-301-3700 (Fax 847-301-3703) Tom Kob

25" x 118" Toolmex #TUR630S, 4.1"bore,fully clutched,14.7"OCS,17"Tri-v bed,20hp,rapid

Toolmex Corp, Schaumburg, IL 847-301-3700 (Fax 847-301-3703) Tom Kob

25" x 120" Nardini #NZ25120, 33"swing in gap, Aloris TP, steady rest, Sony DRO, 2003

Poliquin Machinery Inc, Auburn, ME 207-784-1999 (Fax 207-795-6198) Greg Poliquin

25" x 120" Saber high speed precision gap bed lathe, 5.1"bore, 15 HP, 3&4 jaw, DRO, taper, loaded & nice!

A R Tools & Machinery Inc, Spokane, WA 800-222-3152 (Fax 509-922-2260) Wayne Hoff

25"/36" x 120" Sidney #25HD-16x120"CC, GH/HD 25 HP,2-3/16"bore,thrding,taper,older

Industrial Resources Inc, Old Saybrook, CT 860-388-3439 (Fax 860-388-2740) Ray Magaldi

25" x 120" South Bend Nordic, 15 HP,18-1400 RPM,15"3-Jaw chk,taper,2 steady rests

Scott Machinery & Supply Inc, Helena, AL 205-664-9644 (Fax 205-664-9796) George Scott

25" x 120" Summit #24, 4-1/8"hole, 1250 RPM, manual engine lathe, #3610

Turners Machinery Inc, Santa Paula, CA 805-525-2171 (Fax 805-525-5683) Al Van Wagner

25"/30" x 120" Summit #25-3, gap bed heavy duty engine lathe,22"4-jaw chuck,steady rest,4 way tool post,guaranteed,#A2634

Sterling Machinery Exchange, South El Monte, CA 626-444-0311 (Fax 626-443-9588) Adam Mattes

25"/33" x 120" Summit engine lathe, DRO both Axis,4"bar cap,1250 rpm,taper att.,'07

R & J Machinery Sales, Milford, MI 248-685-7879 (Fax 248-676-0389) Jeff Bruce

25" x 120" Toolmex #TUR-63/120, in/mm,Sony DRO,3-Jaw,Aloris,1980's,#150084

Machinery Values Inc, Harrison, NJ 973-497-7570 (Fax 973-497-7501) David Valitt

25" x 144" American Pacemaker, hardways, 4-jaw chuck

Belmont Machinery Co, Aurora, IL 630-844-9288 (Fax 630-844-9398) Sales

25" x 144" Tos #SU63, 4-Jaw chuck,steady rest,toolpost,25 HP,1120 RPM,#4673

IA Machinery Co, Huntington Park, CA 323-587-1887 (Fax 323-587-1811) Rick Kruger

25" x 150" LeBlond, taper, 1970

Belmont Machinery Co, Aurora, IL 630-844-9288 (Fax 630-844-9398) Sales

25" x 160" Tos #SN63, 2-3/4"bore, 12"3 jaw, 10-1000 RPM, 15 HP, 14"SR

Machinery Solutions Inc, Lexington, SC 803-359-7000 (Fax 803-359-6464) Carl Amick

25"/34" x 160" Tos #SN63C, 1k RPM,Sony DRO,4-way rapids,in/mm,steady rest,'97,#9183

Wisconsin Metalworking Machinery, Waukesha, WI 262-548-6080 (Fax 262-548-6094) J.R. Kraemer

25" x 192" Monarch #612, 12-1500RPM,2-1/16"hole,30HP,18"4-jaw,stdy.rest,'65,#12315

Harris Machine Tools, Inc., Houston, TX 713-462-5800 (Fax 713-462-8222) Sales Dept.

25" x 197" Tos #SUS63, 14"O/C,1180 RPM,2.3"bore,13K lb.capacity,extras,1967,#17809

Prestige Equipment Corp, Melville, NY 631-249-5566 (Fax 631-249-9494) Terry Lashin

25" x 320" Tos #SUS63, 15.3"O/C,9-1120 RPM,13300 lb.cap.,3.2"bore,1977,#20633

Prestige Equipment Corp, Melville, NY 631-249-5566 (Fax 631-249-9494) Terry Lashin

25" x 320" Tos #SUS63, 15.3"O/C,9-1120 RPM,13300 lb.cap.,3.2"bore,1979,#20629

Prestige Equipment Corp, Melville, NY 631-249-5566 (Fax 631-249-9494) Terry Lashin

25" x 320" Tos #SUS63, 15.3"O/C,9-1120 RPM,13300 lb.cap.,3.2"bore,1981,#20631

Prestige Equipment Corp, Melville, NY 631-249-5566 (Fax 631-249-9494) Terry Lashin

25" x 320" Tos #SUS63, 15.3"O/C,9-1120 RPM,13300 lb.cap.,3.2"bore,1979,#20630

Prestige Equipment Corp, Melville, NY 631-249-5566 (Fax 631-249-9494) Terry Lashin

26" x 54" American, geared head engine lathe

Southwest Dynamics Inc, Arlington, TX 817-649-5050 (Fax 817-640-1090) Rick Bomer

26" x 54" Monarch #62/2013, 20"swing o/ways, 15"4-jaw chuck, #53138

Yoder Machinery Sales, Holland, OH 800-622-4463 (Fax 419-865-5557) Sales

26" x 72" LeBlond, 1080 RPM, 4 & 3-Jaw chks, R.O., steady, follow, 1964

S & M Machinery Sales Inc, Warren, MI 586-755-1234 (Fax 586-755-9876) Spencer Minns

26" x 72" LeBlond, 3-jaw chuck, hardways

Belmont Machinery Co, Aurora, IL 630-844-9288 (Fax 630-844-9398) Sales

26" x 80" Lodge & Shipley #AVS, infinite var 25-1500 RPM,taper,18"chuck,great,#4469

Machinery Consultants Inc, Salt Lake City, UT 801-531-9500 (Fax 801-531-9555) Bill Wilson

26" x 96" LeBlond Regal, inch/metric, taper, 1973

Belmont Machinery Co, Aurora, IL 630-844-9288 (Fax 630-844-9398) Sales

26" x 100" Lodge & Shipley Powerturn, 15"4-Jaw,26"sw,14-1160 RPM,Camlock spdl taper

Gahr Machine Co Inc, Euclid, OH 216-732-3035 (Fax 216-732-3082) Bill Rhea

26" x 120" American Pacemaker, 2-1/2"spdl.bore,L type spdl nose,20-1200rpm,chk,pwr fd

Heart Of Wisconsin Mchy Co, Nekoosa, WI 715-886-4926 (Fax 715-886-3016) Fred Parker

26" x 120" LeBlond Regal, taper

Belmont Machinery Co, Aurora, IL 630-844-9288 (Fax 630-844-9398) Sales

26" x 120" Schaerer lathe, 3-1/8" hole

Belmont Machinery Co, Aurora, IL 630-844-9288 (Fax 630-844-9398) Sales

26" x 144" LeBlond Regal, lathe, chuck, 720 RPM, 10 HP, 1973

Raco Industrial Corp, Des Plaines, IL 847-298-8600 (Fax 847-635-8976) Jack Boecher

26" x 144" LeBlond Regal, 5"hole, taper

Belmont Machinery Co, Aurora, IL 630-844-9288 (Fax 630-844-9398) Sales

26" x 144" LeBlond Regal, lathe engine, 10 HP, 1973

Metro Machinery Inc., Memphis, TN 901-942-3363 (Fax 901-948-5750) Bob Beeson

26" x 150" Lodge & Shipley #2XC20, lathe, 2"spindle bore, 1160 RPM, #1207

Vander Ziel Machinery Sales, Alto, MI 616-868-1111 (Fax 616-868-1115) Steve Vander Ziel

26" x 160" Geminis #GE-680S, 3-1/4"bore,12"3-jaw,16-950 RPM,20 HP,16"SR

Machinery Solutions Inc, Lexington, SC 803-359-7000 (Fax 803-359-6464) Carl Amick

26" x 192" LeBlond, threading, steady rest, taper, 10 HP

Pennsylvania Equipment Inc, Grove City, PA 724-458-6162 (Fax 724-458-0753) Thomas Noone

26" x 240" Schaerer, 16"over cross slide,7-1400 RPM,in/mm thread,26 HP,#21912

Prestige Equipment Corp, Melville, NY 631-249-5566 (Fax 631-249-9494) Terry Lashin

26" x 262" Tos #SUS63,6MT,3"spdl.hole,9-710rpm,DRO,20"4-Jaw,SR,30hp,'80,#21224JV

Gahr Machine Co Inc, Euclid, OH 216-732-3035 (Fax 216-732-3082) Bill Rhea

27" x 45" Lehmann Hydratrol, 20 HP,25"chuck,27"faceplate,from storage,great,#7509

Machinery Consultants Inc, Salt Lake City, UT 801-531-9500 (Fax 801-531-9555) Bill Wilson

27" x 96" American Pacemaker, hardways, taper, 4-jaw chuck, 1957

Belmont Machinery Co, Aurora, IL 630-844-9288 (Fax 630-844-9398) Sales

27" x 118" Ryazan #1M63H-3 HD, 4.3"bore,taper att,pwr.feed,Compound 6 way rapid,1990

Shamrock Machinery Co, Houston, TX 713-699-3355 (Fax 713-699-3389) Mike Richards

27" x 120" Cazeneuve #HB725, in/mm,3&4 Jaw,3"hole,hardbed,S/R,20 HP,'70s,#150091

Machinery Values Inc, Harrison, NJ 973-497-7570 (Fax 973-497-7501) David Valitt

27"/37" x 120" Geminis #GE-650, engine lathe, #4637

IA Machinery Co, Huntington Park, CA 323-587-1887 (Fax 323-587-1811) Rick Kruger

27" x 120" Ryazan #1M63B, in/mm,3.5"hole,27 HP,10-1250 RPM,taper attachement,1993

Adams Machinery Co, Lincolnwood, IL 847-673-0556 (Fax 847-673-7636) Sonneborn

27" x 144" Monarch #20"CM, engine lathe,15"3-jaw,21"4-jaw,30 HP,500 RPM,taper,2 steady rests,older but nice,1947,#25734

C.W. Wood Machinery Inc, Cincinnati, OH 800-745-6008 (Fax 513-542-4819) Sales Dept.

27" x 157" Ryazan #1M63H-4HD, 4.13"bore, pwr compound, 6-way rapid, DRO, 2008

Shamrock Machinery Co, Houston, TX 713-699-3355 (Fax 713-699-3389) Mike Richards

28" x 50" Sydney #2550, engine lathe,24"3-jaw chk,4-jaw,DC variable drive/ctrl,#9400

Sterling Machinery Exchange, South El Monte, CA 626-444-0311 (Fax 626-443-9588) Adam Mattes

28" x 96" Axelson #2516, 3"spdl.hole,18"4-jaw chk,thrd.dial,taper att,coolant,#9493

Yoder Machinery Sales, Holland, OH 800-622-4463 (Fax 419-865-5557) Sales

28" x 118" Toolmex #TUR710S, 4.1"bore,17"Tri-V bed,4 way rapids,17"OCS,European,new

Toolmex Corp, Schaumburg, IL 847-301-3700 (Fax 847-301-3703) Tom Kob

28" x 120" Lion #28MS120, engine lathe,18-1/4"SOCS,18"3-Jaw chk,4-1/8"hole,#6 MT,tailstock,in/mm threading,very good,#L300071

N & R Machine Sales, Navasota, TX 800-245-3194 (Fax 936-825-2679) Randy Nevels

28"/33" x 120" Mighty Turn #ML-28120GL, 7.5-1050 RPM,4-1/8"HIS,gap,in/mm,'95,#9453

Turner Industries Inc, Grand Rapids, MI 616-949-5910 (Fax 616-949-3461) Jeff/Bill/David

28"/33" x 120" Mighty Turn #ML-28120GL, 7.5-1050 RPM,4-1/8"HIS,gap,in/mm,'95,#9454

Turner Industries Inc, Grand Rapids, MI 616-949-5910 (Fax 616-949-3461) Jeff/Bill/David

28"/33" x 120" Mighty Turn #ML-28120GL, gap,in/mm,taper attachment,20"4-jaw chuck,coolant,1995,#25848

C.W. Wood Machinery Inc, Cincinnati, OH 800-745-6008 (Fax 513-542-4819) Sales Dept.

28"/33" x 120" Mighty Turn #ML-28120GL, gap bed,in/mm,taper attachment,20 HP, 20"4-jaw chuck,coolant,1995,#25849

C.W. Wood Machinery Inc, Cincinnati, OH 800-745-6008 (Fax 513-542-4819) Sales Dept.

28" x 132" Tos, inch/metric, Steady Rest, Rapid, 4-Jaw

Hardy Machinery Inc, Huntsville, AL 256-536-1319 (Fax 256-536-1322) Ron Hardy

28" x 150" LeBlond Standard Heavy Duty lathe, 1-5/8"spindle bore,17-2000 RPM,#9262

Vander Ziel Machinery Sales, Alto, MI 616-868-1111 (Fax 616-868-1115) Steve Vander Ziel

28" x 150" Lodge & Shipley Series 20, heavy duty engine lathe,taper attach.,clnt,tool post,18"4-jaw chk,2 steady rests,#A2235

Sterling Machinery Exchange, South El Monte, CA 626-444-0311 (Fax 626-443-9588) Adam Mattes

28"/40" x 157" Tos Trencin, gap type engine lathe, 12"3-jaw, 19"4-jaw, #26179

Mohawk Machinery Inc, Cincinnati, OH 513-771-1952 (Fax 513-771-5120) Mr.Secord

28" x 160" Tos #SN71, DRO, taper, steady & follow rest, 4-jaw chuck

Dominion Air & Machinery Co, Roanoke, VA 540-344-8733 (Fax 540-344-3830) Dave Gauvin

28" x 160" Tos #SN71C, 37"swing in gap, 1000 RPM, 4-jaw, taper, steady rest, 10 HP, #15381

Harris Machine Tools, Inc., Houston, TX 713-462-5800 (Fax 713-462-8222) Sales Dept.

28" x 160" Tos, 28"sw.o/bed,17"o/cr.sl,35"sw.w/out gap,3"thru hole,1000 RPM,tpr.attch.

Tas Iron Ltd, Berea, OH 440-973-4394 (Fax 440-973-4395) Timothy Jones

28" x 168" Lodge & Shipley #2516, engine lathe,18"3-jaw,24"4-jaw chuck,taper attachment,rapid traverse,steady rest,#9931

Sterling Machinery Exchange, South El Monte, CA 626-444-0311 (Fax 626-443-9588) Adam Mattes

30" x 48" LeBlond 25"Heavy Duty, taper attachment,65-400 RPM,24"4-jaw chuck,15 HP,thread dial,#24572

C.W. Wood Machinery Inc, Cincinnati, OH 800-745-6008 (Fax 513-542-4819) Sales Dept.

30" x 72" Monarch, Series 80, Chucks, Steady Rests, Coolant, 1960

T R Wigglesworth Machinery, Bedford, OH 440-232-6660 (Fax 440-232-5541) T. Wigglesworth

30" x 74" Monarch #80, Dyna-Shift,1200 RPM,rapids,chucks,steady.DRO,1964

Johnston Industrial Sales Co., Cleveland, OH 216-381-7701 (Fax 216-486-1641) C. Johnston

30" x 80" Ikegai #DAB-36, 50-1000 RPM,3.5"spdl.hole,25"4-Jaw,15"3-Jaw chk,in/mm

Pride Machinery Sales Inc., Deer Park, NY 631-586-5252 (Fax 631-586-3612) Joe Shapiro

30" x 86" Lion, engine lathe, 11"gap, 37"swing in gap, 20"OCS, 1994, #8730

Wisconsin Metalworking Machinery, Waukesha, WI 262-548-6080 (Fax 262-548-6094) J.R. Kraemer

30" x 96" American, taper, hardways, 4-Jaw, 1963

Belmont Machinery Co, Aurora, IL 630-844-9288 (Fax 630-844-9398) Sales

30" x 96" LeBlond, taper

Belmont Machinery Co, Aurora, IL 630-844-9288 (Fax 630-844-9398) Sales

30" x 120" Dainichi engine lathe, 14-1250 RPM, inch/metric, taper attachment

Scott Machinery & Supply Inc, Helena, AL 205-664-9644 (Fax 205-664-9796) George Scott

30" x 120" Kingston #HD30, type 30,40"swing in removable gap,steady rests,1997

Shamrock Machinery Co, Houston, TX 713-699-3355 (Fax 713-699-3389) Mike Richards

30" x 120" LeBlond #NI, sliding bed engine lathe,20"SOCS,steady rest,DRO,20 HP,#59861

Yoder Machinery Sales, Holland, OH 800-622-4463 (Fax 419-865-5557) Sales

30" x 120" Mazak #30, 4"hole, 32"swing, 1200 RPM, #3608

Turners Machinery Inc, Santa Paula, CA 805-525-2171 (Fax 805-525-5683) Al Van Wagner

30" x 120" Mazak Rex, engine lathe, #3608

Turners Machinery Inc, Santa Paula, CA 805-525-2171 (Fax 805-525-5683) Al Van Wagner

30" x 120" Monarch, 4J, 30 HP, low price, #11084

Altman Machinery Co, Chicago, IL 773-247-4343 (Fax 773-247-2666) Howard /Steve

30" x 13' Harrison #M750, 800 RPM,4-Jaw chk,6.5"spdl.hole,in/mm,Heidenhan DRO,'02

Inter-Plant Sales, Hugo, MN 612-281-3736 (Fax 651-207-8933) Rick Canniff

30" x 160" Lansing, 4-1/8"spindle bore, 1000 RPM, chuck, steady, 1970

Raco Industrial Corp, Des Plaines, IL 847-298-8600 (Fax 847-635-8976) Jack Boecher

30" x 200" Mazak #30-200, 4"spindle bore, #3607

Turners Machinery Inc, Santa Paula, CA 805-525-2171 (Fax 805-525-5683) Al Van Wagner

30" x 200" Mazak, engine lathe, #3607

Turners Machinery Inc, Santa Paula, CA 805-525-2171 (Fax 805-525-5683) Al Van Wagner

30" x 18' Sidney, engine lathe, hardways, 1956

Belmont Machinery Co, Aurora, IL 630-844-9288 (Fax 630-844-9398) Sales

31" x 120" Niles #DLZ800, 19"swing O/C,in/mm thread,15.75"chk,900 RPM,35 HP,#22433

Prestige Equipment Corp, Melville, NY 631-249-5566 (Fax 631-249-9494) Terry Lashin

31" x 156" H.E.S. Jupiter #830, 3-jaw chk,3"hole,#6MT,clnt,in/mm,stdy rest,'68,#145378

Machinery Values Inc, Harrison, NJ 973-497-7570 (Fax 973-497-7501) David Valitt

31" x 16' LeBlond H.D. Lathe, taper

Belmont Machinery Co, Aurora, IL 630-844-9288 (Fax 630-844-9398) Sales

32" x 96" American Pacemaker #25, heavy duty engine lathe,4-jaw chk,stdy rest,#58991

Yoder Machinery Sales, Holland, OH 800-622-4463 (Fax 419-865-5557) Sales

32" x 96" American, hardways, 1963

Belmont Machinery Co, Aurora, IL 630-844-9288 (Fax 630-844-9398) Sales

32" x 120"/160" Samstar, heavy duty,5"bore,20 HP,rapid,wide bed,also 40"sw,new

Cleveland Machinery Sales Inc, Cleveland, OH 216-741-8900 (Fax 216-741-8995) F. Petitt

32"/40" x 120" Turnmaster #32"S, 3.25"hole,900 RPM,taper att,rapid trav.on carriage

Denver Machine Tool Inc, Littleton, CO 303-795-8302 (Fax 303-795-7599) Frank Dieveney

32" x 167" Monarch, 8-450rpm,rapid trav,3&4-jaw,2.25"hole,tlstk live w/camlock quill

Century Machinery Co, Los Angeles, CA 213-627-2847 (Fax 213-627-2499) Leon Dietch

32" x 20' Martin, engine lathe, taper, 1964

Belmont Machinery Co, Aurora, IL 630-844-9288 (Fax 630-844-9398) Sales

32" x 264" LeBlond #25NI, 3 & 4-Jaw chucks, steady rests, taper

Scott Machinery & Supply Inc, Helena, AL 205-664-9644 (Fax 205-664-9796) George Scott

32" x 300" LeBlond #3220-25, geared head engine lathe, #7553

Vander Ziel Machinery Sales, Alto, MI 616-868-1111 (Fax 616-868-1115) Steve Vander Ziel

32" x 324" LeBlond Heavy Duty 3220, 3-Jaw chuck,steady rests,air lift tailstock,1973

Scott Machinery & Supply Inc, Helena, AL 205-664-9644 (Fax 205-664-9796) George Scott

32" x 360" LeBlond #NK 3220, 20"OCS, DRO, taper, 1965, #31885

Machinery Network Inc, Encino, CA 310-826-4440 (Fax 310-826-2320) Sales Dept.

32" x 34' Lehmann #32, engine lathe,dual carriage,steady rest,40/20 HP,#58920

Yoder Machinery Sales, Holland, OH 800-622-4463 (Fax 419-865-5557) Sales

33" x 138" Tos #SUS 80, taper, steady, DRO, inch/metric threading

Prime Machinery Inc, Oyster Bay, NY 516-922-7977 (Fax 516-922-9691) Steve Brenner

33" x 275" Okuma #LDA850x7000, 23.6"OCS,in/mm thrdg,750 RPM,30 HP,1962,#22290

Prestige Equipment Corp, Melville, NY 631-249-5566 (Fax 631-249-9494) Terry Lashin

33" x 295" Binns Berry CNC, 9"hole,live mill,Sauter 12-pos trrt,Fagor 8025,'93,#22596

Prestige Equipment Corp, Melville, NY 631-249-5566 (Fax 631-249-9494) Terry Lashin

33" x 320" Tos #SUS-80, 21" Over C/S, Inch/Metric Thrdg, 900 RPM, 30 HP, '80 #21565

Prestige Equipment Corp, Melville, NY 631-249-5566 (Fax 631-249-9494) Terry Lashin

33" x 360" Tos #SUS80, in/mm,taper,Newall DRO,(2)steadies,28"4-Jaw chk,90's,#150497

Machinery Values Inc, Harrison, NJ 973-497-7570 (Fax 973-497-7501) David Valitt

34" x 100" Broadbent #BL16HSK Oil Country SS & SC gap bed lathe

Scott Machinery & Supply Inc, Helena, AL 205-664-9644 (Fax 205-664-9796) George Scott

34" x 120" Mazak #HD-34, 21"3-Jaw chuck,4"hole,(2) steady rest,taper att.,S28467

Perfection Machinery Sales, Elk Grove Village, IL 866-314-4971 (Fax 847-427-8884) Sales Dept.

34" x 120" Tos #SU80, 3.25"bore, 32"4-jaw, 3-jaw chucks, steady rest, 1990's

Girard Machinery Sales, Minesing, ON 705-722-8128 (Fax 705-722-6897) Guy Girard

34" x 160" Cincinnati engine lathe, great condition, priced for fast sale

Holem Group, Miami, FL 305-733-4644 () Franz Melo

34" x 168" Monarch #2516-25, 1500 RPM, 2"hole, inch/metric, 25 HP, 1982, #15459

Harris Machine Tools, Inc., Houston, TX 713-462-5800 (Fax 713-462-8222) Sales Dept.

34" x 240" Lansing, 4"hole, taper, 1985

Belmont Machinery Co, Aurora, IL 630-844-9288 (Fax 630-844-9398) Sales

34" x 240" Monarch #2516-25, 1500 RPM, 2"hole, inch/metric, hardways, 25 HP, 1982, #15458

Harris Machine Tools, Inc., Houston, TX 713-462-5800 (Fax 713-462-8222) Sales Dept.

34" x 20' VDF Wohlenberg #S710, 3-jaw chuck, 14" steady rests, good, 1963

Hadanich Machine Mfg., Inc., Washington, PA 724-225-2440 (Fax 724-225-8112) George Hadanich

34" x 275.5" Okuma, LDA, heavy duty engine lathe,metric threading,taper,S/R,DRO,'62

Scott Machinery & Supply Inc, Helena, AL 205-664-9644 (Fax 205-664-9796) George Scott

34" x 384" Lehmann #32, 22"over cross slide,dual carriage,rapid traverse,40/20 HP,clean,1953,#23485

C.W. Wood Machinery Inc, Cincinnati, OH 800-745-6008 (Fax 513-542-4819) Sales Dept.

34.5" x 60" Monarch, to 405 RPM, taper, hard bed ways, 28"4-Jaw, tool post

Universal Metalworking Equip., Houston, TX 713-675-4145 (Fax 713-675-1294) M. Feinstein

34-1/2" x 144" Axelson #32, engine lathe,20"SOCS,28"4-jaw chuck,D-1-11,#5 MT,S/R,6-555 RPM,25 HP,1942,#L300036

N & R Machine Sales, Navasota, TX 800-245-3194 (Fax 936-825-2679) Randy Nevels

35" x 200" Clausing #MA35200 Large Swing lathe, new, #8436

Vander Ziel Machinery Sales, Alto, MI 616-868-1111 (Fax 616-868-1115) Steve Vander Ziel

36" x 60" LeBlond NK Series, heavy duty geared head engine lathe

Asset Exchange Corporation, Chicago, IL 773-866-9600 (Fax 773-866-9601) Gregg

36" x 76" LeBlond Regal Servo Shift, raised engine lathe,18-720 RPM, standard threads, 24"4-Jaw chuck, 24"face plate

Hoff Online Auctions, Minneapolis, MN 612-521-5500 (Fax 612-331-3291) Denny Hoff

36" x 120" American Pacemaker, hydraulic tracer attach., 885-1750 RPM, tailstock

Anderson Tooling Inc, Fairfield, IA 641-469-6667 (Fax 641-469-6669) Matt Crull

36" x 120" Denham #SR.20V, (1) 3-point steady,(3) 4-point steadies,tooling,S31063

Perfection Industrial Sales, Elk Grove Village, IL 866-314-4971 (Fax 847-427-8884) Dept. Sales

36" x 120" Monarch #3220-24x120, Series 80 Dyna Shift, 40 HP, X LNJ ways, 1996

Shamrock Machinery Co, Houston, TX 713-699-3355 (Fax 713-699-3389) Mike Richards

36" x 120"/196"/236" Poreba #TPK90, 30/42 HP, New Electrics, Remfg. As New

Hanza International, Moorestown, NJ 856-608-9090 (Fax 856-608-0991) Mark Rubin

36" x 120" Poreba #TPK90/3M, 3-3/4"hole,500 RPM,taper,SR,pwr.fd.compound,15/22 KW

Universal Metalworking Equip., Houston, TX 713-675-4145 (Fax 713-675-1294) M. Feinstein

36" x 132" LeBlond #NK, 3"spdl,23"o/slide,5-500 RPM,XY pwr.rapid,50 HP,great,#9495

Machinery Consultants Inc, Salt Lake City, UT 801-531-9500 (Fax 801-531-9555) Bill Wilson

36" x 16' LeBlond, heavy duty lathe, chuck, 255 RPM, 25 HP

Raco Industrial Corp, Des Plaines, IL 847-298-8600 (Fax 847-635-8976) Jack Boecher

36" x 16' LeBlond, Heavy Duty, Engine Lathe, 4-255 RPM, 25 HP

Metro Machinery Inc., Memphis, TN 901-942-3363 (Fax 901-948-5750) Bob Beeson

36" x 17' Poreba #TPK90X5M, 1988

Belmont Machinery Co, Aurora, IL 630-844-9288 (Fax 630-844-9398) Sales

36.5" x 100" LeBlond #36x100, 24.7"sw.o/carriage,1300 RPM,31.4"4-Jaw,inch thrd,1970's

R & J Machinery Sales, Milford, MI 248-685-7879 (Fax 248-676-0389) Jeff Bruce

36.5" x 144" Monarch #25N, 24"over cross slide, taper, 36"chuck, 1951, #28140

Machinery Network Inc, Encino, CA 310-826-4440 (Fax 310-826-2320) Sales Dept.

37" x 96" LeBlond Regal lathe, #9141

Vander Ziel Machinery Sales, Alto, MI 616-868-1111 (Fax 616-868-1115) Steve Vander Ziel

37"/49" x 197" Timemaster, 30 HP,27.5"sw ocs,4"hole,in/mm,DRO,steadies,'01,#1361

Wigglesworth Machinery Co, East Boston, MA 617-567-7210 (Fax 617-561-0265) Gifford

37" x 210" Meuser, 37" sw.o/bed,tailstock.w/210"ctrs, 46" 4-jaw chk,S.R.,'58

Great American Eqpt Co, Cincinnati, OH 513-771-2111 (Fax 513-771-2552) Sales Dept.

37" x 236" Toolmex #TUR930, 25"chk,45HP,8800 lb.cap.,chip,SR,Fanuc 21iT,'08,#21506

Prestige Equipment Corp, Melville, NY 631-249-5566 (Fax 631-249-9494) Paul Lashin

37-1/2" x 108" Monarch, hvy-duty,2-1/4"spdl.hole,tlpst,live center,32"4-jaw chk,#79944

Smith Machinery Co, Ames, IA 515-233-6330 (Fax 515-232-9411) Jim Smith

38" x 144" American, Engine Lathe, Taper, S.R., 3" Hole, 30 HP, New 1975

Solomon Machinery, Eastpointe, MI 586-774-2030 (Fax 586-774-2801) Russ Solomon

38" x 17' VDF engine lathe, 4"spindle bore, 35"4-jaw chuck, 4 steady rests, inch/metric

Mauldin Machine Inc, Jacksonville, AR 501-835-5494 (Fax 501-982-0200) Jerry Mauldin

38" x 20' Lodge & Shipley #3220 Magnaturn, 24"4-jaw,40 HP,1965,stock #53433

Yoder Machinery Sales, Holland, OH 800-622-4463 (Fax 419-865-5557) Sales

39" x 240" American lathe, 22"& 34"4-Jaw chuck, steady rests, 260 RPM, 1943

Scott Machinery & Supply Inc, Helena, AL 205-664-9644 (Fax 205-664-9796) George Scott

39" x 280" Tuda, (16) speeds 6-590 RPM,A1-11 nose,3.15"bore,in/mm,4-Jaw chuck,L513

Ted Grob Sales Inc, Grafton, WI 262-377-8220 (Fax 262-377-0778) Ted Grob

39" Stanko #1658, lathe, 39"swing, 314"bed, 1988

Soudogaz Inc, Chicoutimi, QC 418-889-2002 (Fax 418-889-2012) Charles Potvin

39.308" x 157.233" Potisje #PA 1000DC, heavy duty engine lathe,5.503"bore,27.516"swing over cross slide,30 HP,never used,2006

Rise Tek Inc, Brampton, ON 905-487-3464 (Fax 905-487-3465) Kulwant Chalotra

39.4" x 168" Potisje, 5.5"spdl bore,Newall 2-Axis DRO,2 S/R,36"4-jaw,T/P,demo,like new

Girard Machinery Sales, Minesing, ON 705-722-8128 (Fax 705-722-6897) Guy Girard

39-1/2" x 280" Tuda, 4-Jaw chuck, steady, rapid traverse

Scott Machinery & Supply Inc, Helena, AL 205-664-9644 (Fax 205-664-9796) George Scott

39-3/4" x 48" American Pacemaker, 750 RPM,2.88"hole,4-Jaw,3-Axis DRO,'69,NK-19488

Action Machinery Co Inc, Bethlehem, PA 610-691-6677 (Fax 610-694-0944) Tom Khoury

40" x 48" Monarch #25N, 4-Jaw chk,tracer attach.,hyd.tailstock,toolpost,25 HP,#5382

IA Machinery Co, Huntington Park, CA 323-587-1887 (Fax 323-587-1811) Rick Kruger

40" x 48" Monarch lathe, taper, chuck, 450 RPM, DRO, 20 HP

Raco Industrial Corp, Des Plaines, IL 847-298-8600 (Fax 847-635-8976) Jack Boecher

40" x 72" American Pacemaker, taper, hard ways

Belmont Machinery Co, Aurora, IL 630-844-9288 (Fax 630-844-9398) Sales

40" x 72" Lodge & Shipley, taper, hard ways, 1969

Belmont Machinery Co, Aurora, IL 630-844-9288 (Fax 630-844-9398) Sales

40" x 72" Springfield #44, Heavy Duty Engine Lathe, 24" 4 Jaw Chuck, 12-487 RPM, Ser.#52018, #L300034

N & R Machine Sales, Navasota, TX 800-245-3194 (Fax 936-825-2679) Randy Nevels

40" x 108" Monarch #NN, 405 RPM,2-1/4"hole,4-Jaw,S/R,H/W,DRO,25 HP,1959,#15369

Harris Machine Tools, Inc., Houston, TX 713-462-5800 (Fax 713-462-8222) Sales Dept.

40" x 120" Microcut #BNC40120, Fanuc OiTD,1480 RPM,4 pos.turret,SR,2012,#21740

Prestige Equipment Corp, Melville, NY 631-249-5566 (Fax 631-249-9494) Paul Lashin

40" x 160" Microcut, front & rear turrets,live milling,6"bore,Fanuc OiTD,2012,#21741

Prestige Equipment Corp, Melville, NY 631-249-5566 (Fax 631-249-9494) Paul Lashin

40" x 16' Springfield #30, heavy duty lathe,40"chk,thrding,12-487 RPM,SR,2-1/8"hole

Inter-Plant Sales, Hugo, MN 612-281-3736 (Fax 651-207-8933) Rick Canniff

40" x 200" D-F #CF61100A/5000, engine lathe, taper, steadies

Esco Machine & Supply, Sugar Land, TX 281-277-3726 (Fax 281-277-2891) R.G. Escandon

41" x 72" Axelson, 4"factory raised,27"OCS,to 467 RPM,taper,SR,36"4-Jaw,20 HP

Universal Metalworking Equip., Houston, TX 713-675-4145 (Fax 713-675-1294) M. Feinstein

41" x 144" Axelson, taper, 25"raised

Belmont Machinery Co, Aurora, IL 630-844-9288 (Fax 630-844-9398) Sales

41" x 200" Yuasa lathe, 14"spdl bore,taper,chucks,rapid traverse,in/mm thread,#9225

Vander Ziel Machinery Sales, Alto, MI 616-868-1111 (Fax 616-868-1115) Steve Vander Ziel

41" x 226" LeBlond, 36"4-jaw,tpr,4-way tool post,rapid,ex-large steady,60 HP,nice

Cleveland Machinery Sales Inc, Cleveland, OH 216-741-8900 (Fax 216-741-8995) F. Petitt

41" x 242" Wohlenberg VDF #W45, 36"chuck, tailstock, steady rests, 1950

Clark Machinery Sales LLC, Lutherville, MD 410-252-5494 (Fax 443-269-0660) Troy Clark

41" x 258" Niles, 41" sw.o/bed, tailstock w/258" ctrs, 32" 4-jaw chk, Stdy.Rest

Great American Eqpt Co, Cincinnati, OH 513-771-2111 (Fax 513-771-2552) Sales Dept.

42" x 120" Springfield, heavy duty, gear head engine lathe

Linden Machine Tools, Natick, MA 508-728-2288 (Fax 508-653-1767) Mike Zirlen

42" x 18' VDF Wholenberg, 4-jaw chuck, 1958

Belmont Machinery Co, Aurora, IL 630-844-9288 (Fax 630-844-9398) Sales

42" x 300" Niles heavy duty engine lathe, 15"roller type steady rest,change gears,30"4-jaw chk,3-jaw chk,face plate,#A2229

Sterling Machinery Exchange, South El Monte, CA 626-444-0311 (Fax 626-443-9588) Adam Mattes

42-1/2" x 157-1/2" Skoda #SUA 100PX4000, 2.36" spdl. bore, 54 HP, 250 rpm,steadies,'75

Havlik International Machy, Cambridge, ON 519-624-6240 (Fax 519-624-4119) John Havlik

43" x 120" Romi, 15-spds. 10-750 RPM, 4-3/4" spdl.hole, No.5 MT, #13606

Harris Machine Tools, Inc., Houston, TX 713-462-5800 (Fax 713-462-8222) Sales Dept.

43" x 16' American Pacemaker, taper, hardways, 1956

Belmont Machinery Co, Aurora, IL 630-844-9288 (Fax 630-844-9398) Sales

43" x 192" American, 40 HP,30"SOCS,taper,39"chuck,2 steadies,hard ways,1965,#1428

Wigglesworth Machinery Co, East Boston, MA 617-567-7210 (Fax 617-561-0265) Gifford

43"/53" x 20' Clausing #LA43240, 3-jaw chk,steady rest,tool post,4 way rapid traverse,motorized tailstock,6"bore,2002,#A1244

Sterling Machinery Exchange, South El Monte, CA 626-444-0311 (Fax 626-443-9588) Adam Mattes

43"/55" x 240" Clausing #LA43240, engine lathe, serial #LA204306316, 2002, #4335

IA Machinery Co, Huntington Park, CA 323-587-1887 (Fax 323-587-1811) Rick Kruger

44" x 60" Monarch, ser.#91,750 RPM,4"hole taper,HW,RT,40 HP,1969,ID #11795

Harris Machine Tools, Inc., Houston, TX 713-462-5800 (Fax 713-462-8222) Sales Dept.

44" x 84" Monarch #36NN, engine lathe,30"SOCS,34"4-Jaw chuck,#5 MT,tailstock,inch threading,very good,1943,#L3000123

N & R Machine Sales, Navasota, TX 800-245-3194 (Fax 936-825-2679) Randy Nevels

44" x 35' American Pacemaker lathe, hardways, 600 RPM, 2-carriage, taper, 1952

Belmont Machinery Co, Aurora, IL 630-844-9288 (Fax 630-844-9398) Sales

45" x 19' Monarch #NN, taper

Belmont Machinery Co, Aurora, IL 630-844-9288 (Fax 630-844-9398) Sales

45" x 240" Monarch #2516-35, 1250 RPM,3"hole,inch/metric,hardways,30 HP,1983,#15457

Harris Machine Tools, Inc., Houston, TX 713-462-5800 (Fax 713-462-8222) Sales Dept.

45" x 27' LeBlond #NK

Belmont Machinery Co, Aurora, IL 630-844-9288 (Fax 630-844-9398) Sales

46" x 240" Timemaster, 36"4-Jaw chuck,16"steady-rest,tailstock,taper attachment

KGI Machine Tool, Houston, TX 713-849-9555 (Fax 713-849-9552) Kent Gasaway

46" x 396" American #4025-31, 31"OCS, taper, 1978

Scott Machinery & Supply Inc, Helena, AL 205-664-9644 (Fax 205-664-9796) George Scott

47" x 34" LeBlond #NK lathe, 34"+OCS,150"CD,36"faceplate chuck

Hadanich Machine Mfg., Inc., Washington, PA 724-225-2440 (Fax 724-225-8112) George Hadanich

47" x 197" Niles /WMW, 33"OCS,52.5"gap,4.6-545 RPM,39.5"4-Jaw,4-way TP,SR,1953

A Green Co Inc, Worcester, MA 508-791-6800 (Fax 508-791-6838) Harvey Green

47" x 240" U.S. Indl., 3 & 4-jaw,stdy/follow,options,4013"spdl.hole,new,low price

Machinery Sales Company Inc, Memphis, TN 800-932-8376 (Fax 901-526-2339) D. Williams

48" x 90" Meuser H.D., 66"gap, 400 RPM, 48"4-jaw, 30 HP

Hesco Equipment Sales Co Inc, Houston, TX 713-699-4766 (Fax 713-699-8986) Bob Hess

48" x 96" Lehmann #36, engine lathe,34"SOCS,42"4-jaw chuck,30 HP,4.5-195 RPM,1945,#L3000118

N & R Machine Sales, Navasota, TX 800-245-3194 (Fax 936-825-2679) Randy Nevels

48" x 108" Monarch Series 90, 36"SOC,2x DRO,40 HP,6-750 RPM,excellent,1957,#11169

Hildebrand Machinery Co Inc, York, PA 717-846-2600 (Fax 717-845-9497) Dave Hildebrand

48" x 240" LePont #H600 lathe, 3-5/8"bore, 30 HP motor, 662 RPM, #9017

Vander Ziel Machinery Sales, Alto, MI 616-868-1111 (Fax 616-868-1115) Steve Vander Ziel

48" x 360" Leblond #4025-32, 5-600 RPM, 50 HP, (2) steady rests, #19704

Prestige Equipment Corp, Melville, NY 631-249-5566 (Fax 631-249-9494) Terry Lashin

48" x 360" LeBlond, heavy duty,4-Jaw,(2) S/R,rapid,updated elec,full lgth tracer,'81

Scott Machinery & Supply Inc, Helena, AL 205-664-9644 (Fax 205-664-9796) George Scott

49" x 240" Tos #SU125, engine lathe,3 & 4-Jaw chk, steady rest, in/mm thrdg, #5063

S K Braly Machinery, Mississauga, ON 905-793-8080 (Fax 905-793-2190) Steve Bignell

50"/68" x 20' Okuma #LDA, heavy duty lathe,4-jaw chk,4 way rapid traverse,SR,#A1247

Sterling Machinery Exchange, South El Monte, CA 626-444-0311 (Fax 626-443-9588) Adam Mattes

50"/68" x 240" Okuma #LDA, heavy duty engine lathe, S/N: 4409-0242, #4340

IA Machinery Co, Huntington Park, CA 323-587-1887 (Fax 323-587-1811) Rick Kruger

50" x 240" Summit #50"DC, 40 HP DC vari-speed,removable gap,rapid,taper,1985

Shamrock Machinery Co, Houston, TX 713-699-3355 (Fax 713-699-3389) Mike Richards

50"/62" x 240" Summit #50x240DC, gap bed,in/mm,2-500 RPM,5-1/2"hole,40 HP,well tooled,excellent,1991,#25764

C.W. Wood Machinery Inc, Cincinnati, OH 800-745-6008 (Fax 513-542-4819) Sales Dept.

50" x 282" VDF CNC, 100"in gap,sliding hd,8-pos.trrt,boring att,AB CNC,'80,#16525

Prestige Equipment Corp, Melville, NY 631-249-5566 (Fax 631-249-9494) Terry Lashin

50"/100" x 282" VDF, 100"in gap,450 RPM,8-sta.turret,boring att,AB CNC,'80,#16526

Prestige Equipment Corp, Melville, NY 631-249-5566 (Fax 631-249-9494) Terry Lashin

50" x 312" LeBlond, engine lathe,44"4-Jaw chuck,steady,rapid,full length tracer

Scott Machinery & Supply Inc, Helena, AL 205-664-9644 (Fax 205-664-9796) George Scott

50" x 27' American Pacemaker lathe, taper, 1953

Belmont Machinery Co, Aurora, IL 630-844-9288 (Fax 630-844-9398) Sales

50" x 336" LeBlond, 1.5-165 RPM,threading,44"4-jaw chk,SR,taper attach.,#19703

Prestige Equipment Corp, Melville, NY 631-249-5566 (Fax 631-249-9494) Terry Lashin

50" x 374" Geminis #GE1200-3G, 34"over C/S,in/mm thrd,40 ton cap.,DRO,'85,#21559

Prestige Equipment Corp, Melville, NY 631-249-5566 (Fax 631-249-9494) Terry Lashin

50" x 36' American, 157 RPM, 2-5/8"hole, steady rest, 50 HP, #15121

Harris Machine Tools, Inc., Houston, TX 713-462-5800 (Fax 713-462-8222) Sales Dept.

51"/61" x 100" Graziano, 35"SOCS,48"chuck,6"hole,in/mm,30 HP,1970,#1413

Wigglesworth Machinery Co, East Boston, MA 617-567-7210 (Fax 617-561-0265) Gifford

51"/67" x 320" Summit #50x230, 5.5"spdl.hole,V/S 2-800RPM,in/mm,31"4-jaw chk,tpr,'98

Century Machinery Co, Los Angeles, CA 213-627-2847 (Fax 213-627-2499) Leon Dietch

51"/67" x 320" Summit #50x320, 39"SOCS,2-Axis DRO,4-jaw,#6MT,in/mm,#4882

IA Machinery Co, Huntington Park, CA 323-587-1887 (Fax 323-587-1811) Rick Kruger

52" x 180" American Pacemaker, taper, 1957

Belmont Machinery Co, Aurora, IL 630-844-9288 (Fax 630-844-9398) Sales

52" x 300" Bertram & Sons Heavy Duty Engine Lathe, 12"riser, 20"4-Jaw chuck, Taper Attach., Tool Post, Change Gears, #A2231

Sterling Machinery Exchange, South El Monte, CA 626-444-0311 (Fax 626-443-9588) Adam Mattes

52" x 26' Summit, engine lathe, taper, 5-1/2"hole, 39"OCS, 1998

Belmont Machinery Co, Aurora, IL 630-844-9288 (Fax 630-844-9398) Sales

53" x 160" Poreba #TR135, taper

Belmont Machinery Co, Aurora, IL 630-844-9288 (Fax 630-844-9398) Sales

53" x 196" Poreba #TR135, 40/55 HP,new elec,4-jaw chk,roller stdy.rest,fully reblt.

Hanza International, Moorestown, NJ 856-608-9090 (Fax 856-608-0991) Mark Rubin

53" x 196" Poreba #TR135B1, 40"O/C,500 RPM,inch/metric,53 HP,1977,#19241

Prestige Equipment Corp, Melville, NY 631-249-5566 (Fax 631-249-9494) Terry Lashin

53" x 236" Poreba #TR135B, 40.15"over car.,66"in gap,in/mm thread,54 HP,'81,#22046

Prestige Equipment Corp, Melville, NY 631-249-5566 (Fax 631-249-9494) Terry Lashin

53" x 236" Poreba #TR135B2/6M, 56.9"sw.in gap,4.7"spdl.bore,500 RPM,in/mm,4-Jaw chk

Euro Machine Tool Co, Wauconda, IL 847-968-2000 (Fax 847-968-2001) Frank Turi

53" x 315" Poreba #TR135B, 49"4-Jaw chuck,threading,rapid traverse,60 HP,1978,#21165

Prestige Equipment Corp, Melville, NY 631-249-5566 (Fax 631-249-9494) Terry Lashin

53" x 315" Poreba #TR135Bx8M, 63"in gap,in/mm thread,steady rests,55 HP,'98,#22518

Prestige Equipment Corp, Melville, NY 631-249-5566 (Fax 631-249-9494) Terry Lashin

53" x 27' Poreba #TR135B, 3 steady rests, taper, 1991 (2)

Belmont Machinery Co, Aurora, IL 630-844-9288 (Fax 630-844-9398) Sales

53" x 393" Poreba #TR135, 40/55 HP,new elec,4-jaw chk,roller stdy.rest,fully reblt.

Hanza International, Moorestown, NJ 856-608-9090 (Fax 856-608-0991) Mark Rubin

53" x 551" Poreba #TR-135Bx14M, 40"over C/S,in/mm thrdg,500 RPM,55 HP,1996,#22354

Prestige Equipment Corp, Melville, NY 631-249-5566 (Fax 631-249-9494) Terry Lashin

54" x 240" Jones & Lamson, taper attachment, tracer, threading, steady rests, #21536

Prestige Equipment Corp, Melville, NY 631-249-5566 (Fax 631-249-9494) Terry Lashin

54" x 24' LeBlond HD #NR, taper

Belmont Machinery Co, Aurora, IL 630-844-9288 (Fax 630-844-9398) Sales

54" x 340" Pontiggia #H700, 42"SOCS,in/mm,400 RPM,24"/48"4-Jaw chks,steady rest,'70

Euro Machine Tool Co, Wauconda, IL 847-968-2000 (Fax 847-968-2001) Frank Turi

55" x 240" Dainichi #MH55x240, 4-1/2"hts,56-400 RPM,4-jaw chk,(2)S/R,F/R,v/good,'71

Norman Machine Tool Ltd, Baltimore, MD 410-633-2300 (Fax 410-633-7737) Mike Norman

56" x 160" American Pacemaker, 4-Jaw, 1956

Belmont Machinery Co, Aurora, IL 630-844-9288 (Fax 630-844-9398) Sales

56" x 15' American Pacemaker,42"ocs,hrdwys,4-Jaw,stdy.rest,from Govt.research plant,'59

Belmont Machinery Co, Aurora, IL 630-844-9288 (Fax 630-844-9398) Sales

56" x 192" American Pacemaker, 40 HP,42"over cross,taper,hardways,1956,stk#1359

Wigglesworth Machinery Co, East Boston, MA 617-567-7210 (Fax 617-561-0265) Gifford

58" x 468" Niles, engine lathe,42"SOCS,#6 MT,48"4 boring mills jaws,2.04-94 RPM,30 HP,Pendant ctrl,#L3000117

N & R Machine Sales, Navasota, TX 800-245-3194 (Fax 936-825-2679) Randy Nevels

59" x 118.11" Toss #SU150H/3000, Engine Lathe, 4.80" Spdl.Bore, 30 HP, 355 RPM, 2000

Havlik International Machy, Cambridge, ON 519-624-6240 (Fax 519-624-4119) John Havlik

59" x 21' Lansing, 4"hole, 1971

Belmont Machinery Co, Aurora, IL 630-844-9288 (Fax 630-844-9398) Sales

62" x 17' Poreba #TR155, taper, (2) steady rests

Belmont Machinery Co, Aurora, IL 630-844-9288 (Fax 630-844-9398) Sales

62" x 26' Poreba #TR155, 4-jaw, (2) steady rests, 1985

Belmont Machinery Co, Aurora, IL 630-844-9288 (Fax 630-844-9398) Sales

63" x 126" Poreba #TCC-160x3M, 51"OCS,192 RPM,17.5 ton cap,63"4-Jaw,75 HP,'73,#20277

Prestige Equipment Corp, Melville, NY 631-249-5566 (Fax 631-249-9494) Terry Lashin

63" x 196" SMTCL, 47"over C/S,250 RM,63"4-Jaw,2-Axis DRO,SR,FR,29 HP,'12,#21943

Prestige Equipment Corp, Melville, NY 631-249-5566 (Fax 631-249-9494) Terry Lashin

63" x 200" D-F #CF61160M, Series CF-M, 3-Bed Ways, 12 ton cap.

Esco Machine & Supply, Sugar Land, TX 281-277-3726 (Fax 281-277-2891) R.G. Escandon

63" x 236" Microcut #BNC6500, 6"hole, 4-pos.turret, stdy.rest,Fanuc 0iTD,'12,#16981

Prestige Equipment Corp, Melville, NY 631-249-5566 (Fax 631-249-9494) Paul Lashin

63" x 315" Skoda #SR 1600x8000, lathem 335 RPM, 4-way, 60 HP, #14888

Harris Machine Tools, Inc., Houston, TX 713-462-5800 (Fax 713-462-8222) Sales Dept.

63" x 393" Poreba #TCG160x10M, 51"OCS,40 ton wt cap.,250 RPM,100 HP,'98,#21990

Prestige Equipment Corp, Melville, NY 631-249-5566 (Fax 631-249-9494) Terry Lashin

63" x 35' Heyligenstaedt, 52"over cross slide, steady rest, 4-jaw chuck, 1958

Belmont Machinery Co, Aurora, IL 630-844-9288 (Fax 630-844-9398) Sales

63" x 472" Poreba #TCG-160/12, 63"face plate, 50"over cross slide, 100 HP

Prime Machinery Inc, Oyster Bay, NY 516-922-7977 (Fax 516-922-9691) Steve Brenner

63" x 472" Poreba #TCG-160/12, 63"Faceplate, 50"Over C/S, 100 HP, 1987, #3891

Abbott Machine Co, Alton, IL 800-262-6478 (Fax 618-465-2495) Mike St. Peters

66" x 384" Leblond Tape Turn, 40"over C/S,75 HP,Fanuc 0i,retro 2006,#18008

Prestige Equipment Corp, Melville, NY 631-249-5566 (Fax 631-249-9494) Terry Lashin

66" x 384" Meuser #M6B, 48"SOCS,400 RPM,in/mm thread,DRO,60 HP,1975,#19452

Prestige Equipment Corp, Melville, NY 631-249-5566 (Fax 631-249-9494) Terry Lashin

66" x 480" BTC, dual carriage, steady rests, full threading, 75 ton capacity

Pennsylvania Equipment Inc, Grove City, PA 724-458-6162 (Fax 724-458-0753) Thomas Noone

67" x 118" Skoda #SR1250, inch/metric threading,53"SOCS,315 RPM,53 HP,#19299

Prestige Equipment Corp, Melville, NY 631-249-5566 (Fax 631-249-9494) Terry Lashin

68" x 20' Niles HD, 50"o/cross slide,94 RPM inf.var.,48"4-Jaw,DRO,steady,thdg,1943

AMTAC Corp, Erie, PA 814-838-4629 (Fax 814-838-4557) Russ Taccone,Jr.

70" x 492" Stanko #A-665, 2-carriages,in/mm threading,taper,150 HP,1976,#22165

Prestige Equipment Corp, Melville, NY 631-249-5566 (Fax 631-249-9494) Terry Lashin

70" x 492.12" Stanko #A-665 engine lathe, #9558

Vander Ziel Machinery Sales, Alto, MI 616-868-1111 (Fax 616-868-1115) Steve Vander Ziel

70.87" x 236" Tru-Turn, 55"ove C/S,315 RPM,steady rests,threading,40 HP,'12,#21447

Prestige Equipment Corp, Melville, NY 631-249-5566 (Fax 631-249-9494) Terry Lashin

71" x 236" Tru-Turn, power drive to top slide, 4-jaw, 2 steadys, 2011

Carney Machinery Co, Wilmington, DE 302-571-8382 (Fax 302-571-9538) Mike Carney

74" x 315" WMW Niles DPS1, 61"over carriage,steady rests,in/mm threading,'77,#22882

Prestige Equipment Corp, Melville, NY 631-249-5566 (Fax 631-249-9494) Terry Lashin

78" x 236" Geminis #GE2000, 64"O/C,240 RPM,inch/metric threading,60 HP,1980,#22356

Prestige Equipment Corp, Melville, NY 631-249-5566 (Fax 631-249-9494) Terry Lashin

78" x 40' Poreba #TCG-200, heavy duty,hardened bedways,in/mm,78"4-Jaw chk,steady,'06

Euro Machine Tool Co, Wauconda, IL 847-968-2000 (Fax 847-968-2001) Frank Turi

78" x 551" Poreba #TCG200, 2-carriages,63"OCS,Pr.Compound,40 ton,100 HP,'85,#21963

Prestige Equipment Corp, Melville, NY 631-249-5566 (Fax 631-249-9494) Terry Lashin

80" x 236"/396" Poreba #TCG200,4-jaw chk,100 HP,40 ton,new elecs,remfg.as new

Hanza International, Moorestown, NJ 856-608-9090 (Fax 856-608-0991) Mark Rubin

80" x 473" D-F (2m x 12m) #C61200, Heavy Duty, 3-Way Design

Esco Machine & Supply, Sugar Land, TX 281-277-3726 (Fax 281-277-2891) R.G. Escandon

82" x 118" Tru-Turn, 67"OCS,3154 RPM,15 ton cap,steady rests,in/mm,40 HP,'13,#22715

Prestige Equipment Corp, Melville, NY 631-249-5566 (Fax 631-249-9494) Terry Lashin

82" x 157" Tru-Turn, 67"OCS,3154 RPM,15 ton cap,steady rests,in/mm,40 HP,'13,#22716

Prestige Equipment Corp, Melville, NY 631-249-5566 (Fax 631-249-9494) Terry Lashin

84" x 30' LeBlond HD raised

Belmont Machinery Co, Aurora, IL 630-844-9288 (Fax 630-844-9398) Sales

84" x 40' Stanko #1A670, dual carriage,in/mm,3-Axis DRO,tlstk,steady rest,'80,#58230

Yoder Machinery Sales, Holland, OH 800-622-4463 (Fax 419-865-5557) Sales

87" x 200" (2.2m x 5m) D-F #CW61220, Medium Duty (10 Tons), 2-Way Design

Esco Machine & Supply, Sugar Land, TX 281-277-3726 (Fax 281-277-2891) R.G. Escandon

90" x 33' Craven, 4-ways,2-carriage,50 ton cap,102 RPM,4-jaw,rebuilt 1995

R M S Industries, Inc, Cincinnati, OH 800-485-1125 (Fax 513-232-4900) Rudy Skoff

90" x 396" Craven, 2-carriages,90"o/cross slide & bed,50 ton cap.,thrding,'56,#19487

Prestige Equipment Corp, Melville, NY 631-249-5566 (Fax 631-249-9494) Terry Lashin

94" x 275" Niles #DP1/3, heavy duty,3-way bed,180 RPM,49"chk,S/R,60 HP,pwr.tlstk,'80

Raco Industrial Corp, Des Plaines, IL 847-298-8600 (Fax 847-635-8976) Jack Boecher

98" x 196" Niles #DP1/S2, facing & center lathe,(2) S/R,355 RPM,60 HP,'81,#22643

Prestige Equipment Corp, Melville, NY 631-249-5566 (Fax 631-249-9494) Terry Lashin

98" x 393" Ikegai #TNC125, 83"over C/S,75 ton cap,4-way bed,Fanuc 15TF,'96,#20687

Prestige Equipment Corp, Melville, NY 631-249-5566 (Fax 631-249-9494) Terry Lashin

118" x 590" Skoda, 160 ton capacity, 5-way bed, 1977, #22558

Prestige Equipment Corp, Melville, NY 631-249-5566 (Fax 631-249-9494) Terry Lashin

120" x 18' Monarch Missle Maker engine Lathe, hardened ways, 2-Axis DRO, 1950"s

Stetter Machinery Corp, Zephyr Cove, NV 888-783-8837 () John Stetter

130" x 66' Wagner, 105" C/S, 200 Ton, 4-Jaw, Steadys, Taper, 150 HP, '61/'94

R M S Industries, Inc, Cincinnati, OH 800-485-1125 (Fax 513-232-4900) Rudy Skoff

147" x 72'2" Wagner BANK 710, 141"chk,11.8"bore,220 ton workpiece w/support,1961

Perfection Machinery Sales, Elk Grove Village, IL 866-314-4971 (Fax 847-427-8884) Sales Dept.

147" x 866" Wagner #BNK710, 124"o/carriage,200 ton wt.cap.,3-carr.thrdg,'94,#21555

Prestige Equipment Corp, Melville, NY 631-249-5566 (Fax 631-249-9494) Terry Lashin

180" x 540" Craven, 126" C/S, 150 Ton, 14' 4-Jaw, 475 HP, 25 RPM, 1970

R M S Industries, Inc, Cincinnati, OH 800-485-1125 (Fax 513-232-4900) Rudy Skoff

16' x 50" Clausing (Vectra) Vectrax, $$$

Richlin Machinery Inc, Farmingdale, NY 631-694-9400 (Fax 631-694-9415) Irv Richlin

248" x 630" D-F #C61630, Very Heavy Duty Lathe, New Mach. Immediate Delivery

Esco Machine & Supply, Sugar Land, TX 281-277-3726 (Fax 281-277-2891) R.G. Escandon

Hardinge type collet lathe, #40004

S & S Machinery Co, Brooklyn, NY 718-492-7400 (Fax 718-439-3930) Simon Srybnik

Kerdinand Weipert #W711, Engine Lathe, 1972

Machine Tool Technologies, Milwaukee, WI 414-486-9700 (Fax 414-769-1522) Joe Ryan

Tadu Frontal engine lathe, 84"chuck, never used, 2000

Holem Group, Miami, FL 305-733-4644 () Franz Melo

Torni Tacchi #FTC-41, gap bed lathe,16'6"bed,Sony XY controller,3&4-Jaw chks,tlstk,S/R,Quick Change tool post,s/n #6285

GoIndustry Dovebid, Owings Mills, MD 410-654-7500 (Fax 410-654-5876) Jigar Shah

Weipert #D13653, 2"spindle bore, compound cross slide, tailstock, chip pan

KGI Machine Tool, Houston, TX 713-849-9555 (Fax 713-849-9552) Kent Gasaway

Back to Machinery & Machine Tool listings.

= photo available Spec Sheet

= spec sheet available rfq

= request quote from seller camera

= video available

= Visit dealer's equipment listing
Search Directory for Machinery & Equipment by Category:

Advanced Search