Advanced Search
RSS Blog Surplus Record

Recently Added New and Used Equipment

Below are the 1,027 listings that have been added or updated in the past 9 days. Created: Sat, Jan 31, 2015

General Equipment Section
AIR COMPRESSORS & ACCESSORIES
AIR COMPRESSORS, ROTARY SCREW (Positive Displacement)(Also See Compressors)
171.2 cfm, Atlas Copco #GA30, 40 HP, 132 psi, w/AirTek refrigerated air dryer #CT220, 2001, #48760 Show photo of item Show item detail
Federal Equipment Co, Cleveland, OH 216-271-3500 (Fax 216-271-5210) Joanne Parente
365 cfm, Palatek #75UD, A/C, str, 75 HP, 460V., low hrs, very good cond, air end wty., 2003
Compressor Resources Inc., Lynnwood, WA 425-745-3739 (Fax 425-745-0668) Steve Flamiatos
480 cfm Gardner Denver 100 hp. 460 v. EDH99C yr. 1998 ac/ac 100 psi tested with warranty
Midwest Air Compressor LLC, Waupaca, WI 715-258-8444 (Fax 715-258-8489) Wayne Mckay
480 cfm Gardner Denver 100 hp. 460 v. EBMSLE yr. 1998 ac/ac 100 psi 3 available tested with warranty
Midwest Air Compressor LLC, Waupaca, WI 715-258-8444 (Fax 715-258-8489) Wayne Mckay
650 cfm, GD #EBOOEE, A/C, 150 HP, 460 V., str, open, clean, operationally tested
Compressor Resources Inc., Lynnwood, WA 425-745-3739 (Fax 425-745-0668) Steve Flamiatos
750 cfm Sullair 150 hp. 460 v. LS20-150L AC/AC yr. 1998 100 psi tested with warranty
Midwest Air Compressor LLC, Waupaca, WI 715-258-8444 (Fax 715-258-8489) Wayne Mckay
960 cfm Sullair 200 hp. 460 v. TS20 200H AC/AC yr. 1998 125 psi, EES cooling package tested with warranty
Midwest Air Compressor LLC, Waupaca, WI 715-258-8444 (Fax 715-258-8489) Wayne Mckay
960 cfm Gardner Denver 200 hp. 460 volt ETU99A yr. 2002 125 psi tested with warranty
Midwest Air Compressor LLC, Waupaca, WI 715-258-8444 (Fax 715-258-8489) Wayne Mckay
1000 cfm, Kaeser #ES290, A/C, 200 HP, 460 V., r/v str, encl, very clean, low hrs, excel cond
Compressor Resources Inc., Lynnwood, WA 425-745-3739 (Fax 425-745-0668) Steve Flamiatos
1249 cfm, Ingersoll-Rand #EPE250-2S, 250 hp. 460 V., 125 psi air cooled, rotary, 2 stg, warranty, 2003 tested/warranty$$$
Midwest Air Compressor LLC, Waupaca, WI 715-258-8444 (Fax 715-258-8489) Wayne Mckay
1249 cfm, IR #EPE250-2S, A/C, 250 HP, 460V., r/v str, encl, new controller, clean, tested, '96
Compressor Resources Inc., Lynnwood, WA 425-745-3739 (Fax 425-745-0668) Steve Flamiatos
1300 cfm Gardner Denver 300 hp. 460 v. yr.1998 150 psi hours 26, 460 tested with warranty
Midwest Air Compressor LLC, Waupaca, WI 715-258-8444 (Fax 715-258-8489) Wayne Mckay
1335 cfm, Sullair #TS32-250L, W/C, r/v str, 250 HP, 460 V., cleaned, tested, excellent, 1995
Compressor Resources Inc., Lynnwood, WA 425-745-3739 (Fax 425-745-0668) Steve Flamiatos
1500 cfm Gardner Denver 300 HP 460 v. Rotary Screw Air compressor, air cooled, yr. 2008, 125 psi tested with warranty
Midwest Air Compressor LLC, Waupaca, WI 715-258-8444 (Fax 715-258-8489) Wayne Mckay
1640 cfm, Sullair #TS32-300L, A/C, str, 300 HP, 460V., rmte cooler, clean, air end wty, 1997
Compressor Resources Inc., Lynnwood, WA 425-745-3739 (Fax 425-745-0668) Steve Flamiatos
1640 cfm Sullair 300 hp. 460 v. TS32 300L yr. 1998 100 psi ac/ac 3 available tested with warranty
Midwest Air Compressor LLC, Waupaca, WI 715-258-8444 (Fax 715-258-8489) Wayne Mckay
1740 cfm, IR #EPE350-2S, A/C, 350 HP, 460 V., r/v str, encl, Intellisys control, v/clean, 1998
Compressor Resources Inc., Lynnwood, WA 425-745-3739 (Fax 425-745-0668) Steve Flamiatos
1775 cfm, GD #EAY99A-350, A/C, r/v str, 350 HP, 460V., auot sentry control, turn vlv, excel
Compressor Resources Inc., Lynnwood, WA 425-745-3739 (Fax 425-745-0668) Steve Flamiatos
2200 cfm Sullair 400 hp. 460 v. TS32 400L yr. 2000 100 psi ac/ac 3 available tested with warranty
Midwest Air Compressor LLC, Waupaca, WI 715-258-8444 (Fax 715-258-8489) Wayne Mckay
2600 cfm, Ingersoll-Rand #EPE250-2S, 600 hp. 460 V., 113 psi air cooled, rotary, 2 stg, warranty, 2000$$$ tested/warranty
Midwest Air Compressor LLC, Waupaca, WI 715-258-8444 (Fax 715-258-8489) Wayne Mckay
3000 cfm Sullair 600 hp. 460 v. TS32 400L yr. 1996 100 psi ac/ac 3 available tested with warranty
Midwest Air Compressor LLC, Waupaca, WI 715-258-8444 (Fax 715-258-8489) Wayne Mckay
AIR COMPRESSORS, ROTARY/SLIDING VANE
110 cfm, 115 psi, Gardner-Denver #EBE99M09, s/n #S096440, 25 HP, 460 V., '01, #16598
F P Miller Company, Jackson, MI 517-787-3100 (Fax 517-787-3116) Craig L. Ward
AIR COMPRESSORS, TANK MOUNTED
7.5 HP Ingersoll-Rand #2475N7.5, air compressor, 24 cfm, 175 psi Show photo of item Show item detail
Miedema Auctioneering & Appraisals Inc, Byron Center, MI 616-538-0367 (Fax 616-538-5230) Amada Bowers
BALERS,PAPER & METAL (Also See Scrap Yard Machinery & Equipment)
BALERS, PAPER & CORRUGATED MATERIALS
60" x 30" Piqua #30, vert., 60" W x 30" D bales & feed open, dwn.act.hyd.cyl, 7.5HP, 230/460 V.hyd.pwr.pak, controls, #48759 Show photo of item Show item detail
Federal Equipment Co, Cleveland, OH 216-271-3500 (Fax 216-271-5210) Joanne Parente
BAR FEEDS (Also See Tooling & Accessories, Bar Feeds)
Iemca Master #880MP-E, 5/16 to 3-1/8" bar, 12' length, 2005 Show photo of item
520 Machinery Sales LLC, Schaumburg, IL 888-520-1768 (Fax 630-855-3535) Everett Dahlberg
Iemca Master 880/38MP-E, 3" x 12', 2005, Hydraulic Unit, 52mm channel set Show photo of item Show item detail
Automatics & Machinery Co Inc, Longmont, CO 800-543-7666 (Fax 303-651-6556) Steve Beck
LNS #6.32H-4.9 Super Hydrobar CNC Barstock Feeders, #6998
Scott Machinery & Supply Inc, Helena, AL 205-664-9644 (Fax 205-664-9796) George Scott
LNS #HYS 6.26 HS-4.8, 1/16" - 1" x 12', Tube Only Show photo of item Show item detail
Automatics & Machinery Co Inc, Longmont, CO 800-543-7666 (Fax 303-651-6556) Steve Beck
LNS #HYS 6.26 HS-4.8, 1/16" - 1" x 12', 6 tube Gatling type, sliding/fixed headstock Show photo of item Show item detail
Automatics & Machinery Co Inc, Longmont, CO 800-543-7666 (Fax 303-651-6556) Steve Beck
BENDERS, BAR, PIPE & TUBE (Also See CNC Machinery & Equipment)
1-1/4" Pines #3T, vertical, digital Dial-a-Bend control, 20 HP, (2) in stock, #sr4744/5 Show photo of item Show item detail
Alma Machinery Co Inc, Columbia, TN 615-369-7788 (Fax 615-369-7789) Ken King
4" Conrac #244RH, right hand bend, 24" bend radius, 180°max bend angle, 25 HP Show photo of item Show item detail
Wheeler Machinery Sales, Pomona, CA 888-589-6721 (Fax 909-348-5617) Dan Wheeler
BENDERS, HAIRPIN (Also See Benders, Bar, Pipe & Tube)
Greenlee #882, hydraulic tube bender, capacity: 2" max pipe to 2 EMT Rigid conduit Show photo of item
Netmachinery Inc., Mooresville, NC 704-660-8130 (Fax 704-663-3475) David Kragh
BORING MILLS, HORIZONTAL, Floor Type, (Also See Planer and Table Types)
Tos #WD130A, travelling column floor type horizontal boring mill Show photo of item Show item detail
Hilco Industrial LLC, Farmington Hills, MI 248-419-1964 (Fax 248-254-9995) Ken Planet
BORING MILLS, HORIZONTAL, Table Type (Also See CNC Machinery & Equipment)
3" Ceruti #ABC-75, 3" spindle, #4 spindle taper, 33.4" x43.3" rotary table, 15-1500 RPM, 10 HP, s/n #11993, good, #B550041 Show photo of item Show item detail
N & R Machine Sales, Navasota, TX 800-245-3194 (Fax 936-825-2679) Randy Nevels
4" Giddings & Lewis #65E4T, 48" x98" tbl, 84" X, 48" Y, 32" Z, 50NST, 1963, #5350
Scott Machinery & Supply Inc, Helena, AL 205-664-9644 (Fax 205-664-9796) George Scott
4" Nomura B100WR, X-63" , Y-60" , Z-26" , W-50" , 63" X 55" Built-In Rotary Table, # 50 Taper, 1981 Show photo of item Show item detail
Perfection Industrial Sales, Elk Grove Village, IL 847-427-3333 (Fax 847-427-8884) Dept. Sales
4" Nomura #B100BT-2, 48" x72" table, #50 taper, 1200 RPM, 3-Axis Acu-Rite RO, 1978 Show photo of item
Bayshore Industrial Sales Inc, Grosse Pointe, MI 313-881-2120 (Fax 313-881-4855) Eric Hoffman
4" Tos #W-100A, #50 taper, Heidenhain DRO, 48" x48" rotary tbl, 63" x45" x50" trvls, 1990 Show photo of item
Industrial Machinery Exchange, Cambridge, ON 519-622-8353 (Fax 519-622-8351) Paul Geddes
4" Tos #W100A, 63" x44" x49" , 49" x49" built-in r/tbl, facing head, tlstk, 4-Axis DRO, 1998 Show photo of item Show item detail
Girard Machinery Sales, Minesing, ON 647-477-9433 Guy Girard
4" Toshiba, HBM, rotary, #50 w/PDB, 1974
Belmont Machinery Co, Aurora, IL 630-844-9288 (Fax 630-844-9398) Sales
4.25" Sacem, HBM, rotary, #50 spindle, 1980
Belmont Machinery Co, Aurora, IL 630-844-9288 (Fax 630-844-9398) Sales
4.25" Summit Horizontal, 71" x79" rotary table, #50 taper, 1200 RPM, 86" x80" x80" trvls Show photo of item
Industrial Machinery Exchange, Cambridge, ON 519-622-8353 (Fax 519-622-8351) Paul Geddes
4-1/4" Wotan #B110, 49" x55" rotary table, #5 Morse spindle taper, tailstock, s/n #54253, 20 HP, good, #B550011 Show photo of item Show item detail
N & R Machine Sales, Navasota, TX 800-245-3194 (Fax 936-825-2679) Randy Nevels
5" Giddings & Lewis #350T, HBM, 60" x 98" table, 1958
Belmont Machinery Co, Aurora, IL 630-844-9288 (Fax 630-844-9398) Sales
5" G & L #350T, 5" spindle, 48" x84" table, #6 Morse spindle taper, 6.25-375 RPM, tailstock, s/n #5236, good, 1942, #B550056 Show photo of item Show item detail
N & R Machine Sales, Navasota, TX 800-245-3194 (Fax 936-825-2679) Randy Nevels
5" Giddings & Lewis #70A-DP5-T, pendant control, DRO, outrigger Show photo of item
Asset Exchange Corporation, Chicago, IL 773-866-9600 (Fax 773-866-9601) Scott / Mark
5" Giddings & Lewis #70D5T, 48" x 144" table, 72" vertical, #5MT, 1969
O'Connell Machinery Co, Buffalo, NY 716-877-3666 (Fax 716-877-1136) W. O'Connell
5" Union #BFT125-5, horizontal, 55" x63" rotary tbl, #50 taper, facing head, tailstock, DRO Show photo of item
Industrial Machinery Exchange, Cambridge, ON 519-622-8353 (Fax 519-622-8351) Paul Geddes
5.375" Cincinnati Gilbert JT, X-120" , Y-84" , Z-36" , 60" X 120" Table, Ball Screws, 1978 S33330 Show photo of item Show item detail
Perfection Industrial Sales, Elk Grove Village, IL 847-427-3333 (Fax 847-427-8884) Dept. Sales
BORING MILLS, VERTICAL, Includes VTL's (Also See CNC Machinery & Equipment)
42" Bullard Cutmaster high column VTL, 54" swing, 48" under rail, side & turret head, 1953, #B600676 Show photo of item Show item detail
N & R Machine Sales, Navasota, TX 800-245-3194 (Fax 936-825-2679) Randy Nevels
42" Bullard Cutmaster, VTL, 42" 3-Jaw, 5.5-200 RPM, 30 HP, RAM head, s/n #27943, good, 1953, #B600669 Show item detail
N & R Machine Sales, Navasota, TX 800-245-3194 (Fax 936-825-2679) Randy Nevels
43" Defum #KNA110/135, 23.6" travel, 6-pos turret, 40 HP, ram side head, threading, 1994 Show item detail
Adams Machinery Co, Lincolnwood, IL 847-673-0556 (Fax 847-673-7636) Sonneborn
52" King, VTL, 52" face plate, 3-96 RPM, 25 HP, 440 V., built-in 4-way tool post on side head, good, #B600668 Show photo of item Show item detail
N & R Machine Sales, Navasota, TX 800-245-3194 (Fax 936-825-2679) Randy Nevels
54" Bullard #54 Spiral Drive, 50" 4-Jaw, 3.5-60 RPM, 35 HP, s/n #20458, very good, 1942, #B600618 Show photo of item Show item detail
N & R Machine Sales, Navasota, TX 800-245-3194 (Fax 936-825-2679) Randy Nevels
56" Bullard Dynatrol, vertical boring mill, 56" 4-jaw w/top jaws, 1960, #B600694 Show photo of item Show item detail
N & R Machine Sales, Navasota, TX 800-245-3194 (Fax 936-825-2679) Randy Nevels
74" Bullard Cutmaster, 74" table, 4 boring mill jaws, 82" swing, 3.3-120 RPM, 40 HP, s/n #25130, good, 1946, #B600695 Show photo of item Show item detail
N & R Machine Sales, Navasota, TX 800-245-3194 (Fax 936-825-2679) Randy Nevels
Okuma-Howa #ACT 2SP V3, VTL, 20" swing, 13.78" X, 16.14" Z, 23.62" cc, 12 turret, 1995 (2) Show photo of item Show Video of Item Show item detail
R & J Machinery Sales, Milford, MI 248-685-7879 (Fax 248-676-0389) Jeff Bruce
BRAKES, APRON & HAND
14 Ga. x 8' D & K 814, Hand-Op Show photo of item
Altman Machinery Co, Chicago, IL 773-247-4343 (Fax 773-247-2666) Howard /Steve
18 Ga. x 12' D & K 1218, Hand-Op Show photo of item
Altman Machinery Co, Chicago, IL 773-247-4343 (Fax 773-247-2666) Howard /Steve
12 ga. x 8' Chicago Dries & Krump #SO-812, apron brake Show photo of item
Machine Tool Technologies, Milwaukee, WI 414-486-9700 (Fax 414-769-1522) Joe Ryan
BRAKES, BOX & PAN
12 ga. x 8' Chicago #BPO-812-6, box and pan finger brake, 2 counter weights, 16 fingers, #A3645 Show Video of Item
Sterling Machinery Exchange, South El Monte, CA 626-444-0311 (Fax 626-443-9588) Adam Mattes
BRAKES, PRESS (GAUGES)
14 ga. x 10' Mercury #3508, mechanical press brake, 120" bed & RAM, 8" throat, hand operated BG, s/n #5419-46L Show photo of item Show Video of Item Show item detail
Hoff Online Auctions, Minneapolis, MN 612-521-5500 (Fax 612-331-3291) Denny Hoff
10/14 ga. x 10' Roto-Die #15, hydraulic, 7.5 HP, with tooling Show photo of item
SMF & Machine Tools Inc, Little Rock, AR 800-643-5839 (Fax 501-897-4090) Teresa Glover
BRAKES, PRESS (TONS) (Also See CNC Machinery & Equipment - Brakes, Press)
17 Ton, DiArco #14-48-2, mechanical press brake, 48" bed & RAM, 2" stroke, 2" RAM adj., 18" hand operated BG, 3 HP, s/n #JD-1029 Show photo of item Show Video of Item Show item detail
Hoff Online Auctions, Minneapolis, MN 612-521-5500 (Fax 612-331-3291) Denny Hoff
17 Ton, DiAcro #14-48-2, mechanical press brake, 48" bed & RAM, 2" stroke, 6.5" throat, 18" hand operated BG, 3 HP, s/n #JD-1028 Show photo of item Show Video of Item Show item detail
Hoff Online Auctions, Minneapolis, MN 612-521-5500 (Fax 612-331-3291) Denny Hoff
40 Ton, Mercury #5004, 6' OA, air assisted clutch, 3" stroke, 5 HP, manual back gauge Show photo of item Show Video of Item Show item detail
Wheeler Machinery Sales, Pomona, CA 888-589-6721 (Fax 909-348-5617) Dan Wheeler
45 Ton, Heim #45-10, mechanical press brake, 10'-6" bed & RAM, 2" stroke, 24" hand operated BG, 2 HP, s/n #1783 Show photo of item Show Video of Item Show item detail
Hoff Online Auctions, Minneapolis, MN 612-521-5500 (Fax 612-331-3291) Denny Hoff
55 Ton, Dreis & Krump #68-B, mechanical, manual back gauge, 3 HP, 3" stroke, 1980 Show photo of item Show Video of Item Show item detail
Wheeler Machinery Sales, Pomona, CA 888-589-6721 (Fax 909-348-5617) Dan Wheeler
99 Ton, Durma #AD-E3090, Delem DA-51 2-Axis, 10' OA, 2007, #10184 Show photo of item
Jordan Craig Machinery Intl L, New City, NY 845-398-0073 (Fax 845-398-0074) Jordan Craig
100 Ton, Wysong, hydraulic, 12' OA, 10-6 BH
SMF & Machine Tools Inc, Little Rock, AR 800-643-5839 (Fax 501-897-4090) Teresa Glover
110 Ton, Amada #HFE-1003S/7, Amada Operateur, 10.2' OA, 106" BH, 2000, #10186
Jordan Craig Machinery Intl L, New City, NY 845-398-0073 (Fax 845-398-0074) Jordan Craig
120 Ton, Allsteel hydraulic brake press, 10' OA
Greenway & Associates Ltd, Orange City, IA 712-737-8700 (Fax 712-737-8701) Clark Groeneweg
120 Ton, Krras brake press, 8' OA, Automec 2-Axis, 2006
Greenway & Associates Ltd, Orange City, IA 712-737-8700 (Fax 712-737-8701) Clark Groeneweg
123 Ton, Baileigh #BP-12313NC, Delem 2-Axis, 2008, installed new 2011, #10183 Show photo of item
Jordan Craig Machinery Intl L, New City, NY 845-398-0073 (Fax 845-398-0074) Jordan Craig
143 Ton, Amada #HDS-1303NT, AMNC-PC 8-Axis, 10.7' OA, 106.3" BH, 2003, #10185 Show photo of item
Jordan Craig Machinery Intl L, New City, NY 845-398-0073 (Fax 845-398-0074) Jordan Craig
165 Ton, LVD brake press, 10' OA, MRC 8000 3-Axis gauge, 1987
Greenway & Associates Ltd, Orange City, IA 712-737-8700 (Fax 712-737-8701) Clark Groeneweg
230 Ton, Cincinnati #230AF10, 2-Axis, 12' OA, crowning, updated control, 1988, #10182
Jordan Craig Machinery Intl L, New City, NY 845-398-0073 (Fax 845-398-0074) Jordan Craig
230 Ton, Cincinnati brake press, 12' OA, Automec 2-Axis CNC
Greenway & Associates Ltd, Orange City, IA 712-737-8700 (Fax 712-737-8701) Clark Groeneweg
250 Ton, Mastefab, hyd.press brake, 12' OA, crowning, 1-Axis Automec 1000 CNC BG Show photo of item Show Video of Item Show item detail
Naab Sales Corporation, Hopkins, MN 952-933-6755 (Fax 952-933-7229) J.Van Heuveln
0055t d & k 8l10, 10' o.a., 8'6" b.h., v/s Show photo of item
Altman Machinery Co, Chicago, IL 773-247-4343 (Fax 773-247-2666) Howard /Steve
BROACHING MACHINES, VERTICAL
PULL DOWN BROACHING MACHINES
25 Ton x 54" str., U.S. Broach & Machine #25t x 54, vertical pull-down broaches Show photo of item Show item detail
Hilco Industrial LLC, Farmington Hills, MI 248-419-1964 (Fax 248-254-9995) Ken Planet
CHEMICAL, PETROLEUM, GAS & PROCESSING EQUIPMENT
ATTRITORS
Astro Air, Attrition Tester, w/Stainless Steel Attrition Test Chamber, On Stand, #48779 Show photo of item Show item detail
Federal Equipment Co, Cleveland, OH 216-271-3500 (Fax 216-271-5210) Joanne Parente
Union Process #HSA-1, 1.3 gal.cap, 4-gal.work cap, .3-.5-gal.media cap, 2-jktd.bowls w/beaters, on base, 230/460V.XP, #48777 Show photo of item Show item detail
Federal Equipment Co, Cleveland, OH 216-271-3500 (Fax 216-271-5210) Joanne Parente
AUTOCLAVES (Also See Reactors)
Autoclave Engineers, Stainless Steel autoclave body, 5800 psi @ 650° F, elec.htd, removable bolt on top, dish bottom, no.agit.dr, #48788 Show photo of item Show item detail
Federal Equipment Co, Cleveland, OH 216-271-3500 (Fax 216-271-5210) Joanne Parente
Autoclave Engs., Stainless Steel autoclave body, 5800 psi @ 650° F, elec.htd, removable bolt on top, dish bottom, no.agit.dr, #48789 Show photo of item Show item detail
Federal Equipment Co, Cleveland, OH 216-271-3500 (Fax 216-271-5210) Joanne Parente
CENTRIFUGES
7.8" x 3.9" Rousselet-Robatel #RC-20-VXR, Hast. C22, perf.basket, 2-liter bowl, 2.5Kg max. load, 3000 RPM, 230 V.XP, #48851 Show photo of item Show item detail
Federal Equipment Co, Cleveland, OH 216-271-3500 (Fax 216-271-5210) Joanne Parente
48" x 39: Sanborn, perf.basket, Stainless Steel, top load, bottom unload, feed pipe, sgl.act.plow disch, cake sensor, tri-pod suspension, #48762 Show photo of item Show item detail
Federal Equipment Co, Cleveland, OH 216-271-3500 (Fax 216-271-5210) Joanne Parente
CLASSIFIERS (Also See Screens)
Witte, 48" x84" classifier, (1)deck, (2)separations, s/n #3688-P, 15 HP, #8405 Show photo of item
Arlington Plastics Machinery, Elk Grove Village, IL 847-956-7300 (Fax 847-956-8585) Sales
DISPERSERS, HIGH SPEED (Also See Mixers-Blenders, Dispersion)
2 HP Shar Disperser, Stainless Steel shaft & blade, pneumatic lift, 230/460 v. XP motor, on stand, #48758 Show photo of item Show item detail
Federal Equipment Co, Cleveland, OH 216-271-3500 (Fax 216-271-5210) Joanne Parente
3 HP Myers #L775-3, Disperser, Stainless Steel shaft & blade, pneumatic lift, 230/460 V. XP motor, on stand, Ser. #2132, 1991, #48735 Show photo of item Show item detail
Federal Equipment Co, Cleveland, OH 216-271-3500 (Fax 216-271-5210) Joanne Parente
10 HP Schold VS disperser, air/oil lift, FL MT, CS shaft, 230/460 V. Show photo of item
DMBS, Houston, TX 713-847-7775 (Fax 713-847-9994) Mark Nawrot
10 HP Schold VS Disperser, air/oil lift, FL MT, CS shaft & blade, 230/460 V.
DMBS, Houston, TX 713-847-7775 (Fax 713-847-9994) Mark Nawrot
15 HP Hockmeyer #HV-15, Stainless Steel shaft & blade, vari-spd, air over oil hyd. lift w/air tank, 230/480 V. XP motor, floor mtd, #48737 Show photo of item Show item detail
Federal Equipment Co, Cleveland, OH 216-271-3500 (Fax 216-271-5210) Joanne Parente
15 HP Hockmeyer #HV-15, Stainless Steel shaft & blade, air over oil hyd.lift, air tank, 200-230/460 V.XP motor, flr.mtd, #48756
Federal Equipment Co, Cleveland, OH 216-271-3500 (Fax 216-271-5210) Joanne Parente
20 HP Cayuga #L7BVS19025, Stainless Steel shaft & blade, air over oil hyd.lift, air tank, floor mtd, #48756 Show photo of item Show item detail
Federal Equipment Co, Cleveland, OH 216-271-3500 (Fax 216-271-5210) Joanne Parente
30 HP Myers VS disperser, air/oil lift, FL MT, SS shaft & blade, 230/460 V. Show photo of item
DMBS, Houston, TX 713-847-7775 (Fax 713-847-9994) Mark Nawrot
60 HP Scholds, C/S Shaft Disperser, Stainless Steel blade, air over oil hyd, lift, air tank, 230/460 V.XP motor, mech.vari-spd, base mtd, #48734 Show photo of item Show item detail
Federal Equipment Co, Cleveland, OH 216-271-3500 (Fax 216-271-5210) Joanne Parente
DRYERS, Including Kilns & Coolers
Glatt Uni Glatt, fluid bed dryer, Stainless Steel, 1.1 KW fan, 1.76 KW elec.heater, 220 V., less chambers, AS IS, #48908 Show photo of item Show item detail
Federal Equipment Co, Cleveland, OH 216-271-3500 (Fax 216-271-5210) Joanne Parente
VWR #1350FD, 2300 Watt Heater, 240 V., Single Phase, #48787 Show photo of item Show item detail
Federal Equipment Co, Cleveland, OH 216-271-3500 (Fax 216-271-5210) Joanne Parente
FERMENTATION UNITS
B Braun BioStat C, 316 Stainless Steel, 15 liter, flat top, dish bttm, -1/+3 bar @ 150°C int, jktd.-1/+6 bar @ 150°C, M.D., control.panel, #48819 Show photo of item Show item detail
Federal Equipment Co, Cleveland, OH 216-271-3500 (Fax 216-271-5210) Joanne Parente
B Braun BioStat C, 316 Stainless Steel, 15 liter, flat top, dish bttm, 43 psi & FV @ 300° F int, jktd. 58 psi, control.panel, NB #54, 1996, #48818 Show photo of item Show item detail
Federal Equipment Co, Cleveland, OH 216-271-3500 (Fax 216-271-5210) Joanne Parente
B Braun BioStat C, 316 Stainless Steel, 15 liter, flat top, dish bttm, 43 psi & FV @ 300° F int, jktd. 58 psi, control.panel, NB #54, #48817 Show photo of item Show item detail
Federal Equipment Co, Cleveland, OH 216-271-3500 (Fax 216-271-5210) Joanne Parente
FILTERS, MISCELLANEOUS
Siemens RO skid, 8-vert. Stainless Steel RO filter housings, Grundfos vert.pump, skid mounted w/control panel, #48914 Show photo of item Show item detail
Federal Equipment Co, Cleveland, OH 216-271-3500 (Fax 216-271-5210) Joanne Parente
GRANULATORS (Also See Plastic & Rubber Equipment)
Collette #GRAL-10, 10 Liter, high shear, Stainless Steel product contact surface, no-jktd.bowl, manual bowl lift on base, #48892 Show photo of item Show item detail
Federal Equipment Co, Cleveland, OH 216-271-3500 (Fax 216-271-5210) Joanne Parente
HEAT EXCHANGERS, CS SHELL-ALLOY,HASTELLOY,KARBATE,MONEL,TITANIUM TUBES
27 cu.ft. Doyle & Roth, C276 tubes, 430 psi & FV @ 600° F, C/S shell 150 psi & FV @ 450° F, sgl.pass, less bonnets, #48842 Show photo of item Show item detail
Federal Equipment Co, Cleveland, OH 216-271-3500 (Fax 216-271-5210) Joanne Parente
HEAT EXCHANGERS, STAINLESS STEEL SHELL-STAINLESS STEEL TUBES
5914 sq.ft., Manning & Lewis, 204 Stainless Steel, shell/tubes-75 psi @ 800° F, C/S skirt, sgl.pass, NB #6892, 1988, $48727 Show photo of item Show item detail
Federal Equipment Co, Cleveland, OH 216-271-3500 (Fax 216-271-5210) Joanne Parente
HOMOGENIZERS
Ross #HSM-525, High Shear Mix Emulsifier, Stainless Steel, 4.5" diameter rotor stator, 64" L wetted parts, 25 HP DC motor, 230/460V./3510 RPM XP, #48730 Show photo of item Show item detail
Federal Equipment Co, Cleveland, OH 216-271-3500 (Fax 216-271-5210) Joanne Parente
Ross #HSM-525, High Shear Mix Emulsifier, Stainless Steel, 4.5" diameter rotor stator, 64" L wetted parts, 25 HP DC motor, 230/460V./3510 RPM XP, #48731 Show photo of item Show item detail
Federal Equipment Co, Cleveland, OH 216-271-3500 (Fax 216-271-5210) Joanne Parente
MILLS (Also See Mills, Pug, this Section)
CB Mills Red Head Sand Mill #16P, open face, 230/460 V., 1760 RPM, 25 HP, UL motor Show photo of item
DMBS, Houston, TX 713-847-7775 (Fax 713-847-9994) Mark Nawrot
J T Homoloid Fitzmill, Stainless Steel, pan feed, on S/S base, belt driven with XP motor, #48849 Show photo of item Show item detail
Federal Equipment Co, Cleveland, OH 216-271-3500 (Fax 216-271-5210) Joanne Parente
Premier horizontal media mill, 5 liter, 1.5 HP pump motor, 20 HP UL rated main motor Show photo of item
DMBS, Houston, TX 713-847-7775 (Fax 713-847-9994) Mark Nawrot
MILLS, MEDIA
Chicago Boiler #L5P, Vertical Sand Mill, On Stand, #48736 Show photo of item Show item detail
Federal Equipment Co, Cleveland, OH 216-271-3500 (Fax 216-271-5210) Joanne Parente
MIXERS-BLENDERS, AGITATOR
1.5 HP Chemineer #2HTA, Agitator, 230/460 V. motor, mech.seal, w/2" diameter x 76" L Stainless Steel shaft, turbinine agitator, #48841 Show photo of item Show item detail
Federal Equipment Co, Cleveland, OH 216-271-3500 (Fax 216-271-5210) Joanne Parente
1.5 HP Chemineer #2HTA, Agitator, 230/460 V. motor, mech.seal, w/2" diameter x 76" L Stainless Steel shaft, turbinine agitator, #48840 Show photo of item Show item detail
Federal Equipment Co, Cleveland, OH 216-271-3500 (Fax 216-271-5210) Joanne Parente
2 HP Chemineer #26TD-2, Agitator, 230/460 V., 2.5" x 182" L Stainless Steel shaft, 2-tier, 3-blade turbine style agitator, #48799 Show photo of item Show item detail
Federal Equipment Co, Cleveland, OH 216-271-3500 (Fax 216-271-5210) Joanne Parente
MIXERS-BLENDERS, CONE
2 cu.ft. Gemco, Stainless Steel, 300#/cu.ft.mat.density, 10" feed port/cover, 4" disch, man.butterfly valve, on base, motor dr, 1983, 348835 Show photo of item Show item detail
Federal Equipment Co, Cleveland, OH 216-271-3500 (Fax 216-271-5210) Joanne Parente
MIXERS-BLENDERS, DISPERSION (Also See Dispersers (This Section)
Schold VS Bowtie mixer, air/oil lift, 7-1/2 HP, FL MT, CS shaft, 460 V., 50-250 RPM, 3 ph Show photo of item
DMBS, Houston, TX 713-847-7775 (Fax 713-847-9994) Mark Nawrot
MIXERS-BLENDERS, PLOW
Littleford #FKM4200D, Stainless Steel, 148 cu.ft., 87 cu.ft.work cap, jktd.chamber 75 psi, 75 HP main dr, Falk gearbox, on stands, #48907 Show photo of item Show item detail
Federal Equipment Co, Cleveland, OH 216-271-3500 (Fax 216-271-5210) Joanne Parente
MIXERS-BLENDERS, RIBBON
35 cu.ft. Scott #SPM404SS, SS, Reliance XE AC, 10 HP, 230/460 V., 2002, #8458 Show photo of item
Arlington Plastics Machinery, Elk Grove Village, IL 847-956-7300 (Fax 847-956-8585) Sales
MIXERS-BLENDERS, TWIN SHELL (V-TYPE)
10 cu.ft. Patterson-Kelley, twin shell " V" blender, stainless steel, also 5 cu.ft.
Wohl Associates Inc, Bohemia, NY 631-244-7979 (Fax 631-244-6987) Andrew Wohl
100 cu.ft. Gemco, twin shell " V" blender, stainless steel, pharmeceutical use
Wohl Associates Inc, Bohemia, NY 631-244-7979 (Fax 631-244-6987) Andrew Wohl
MIXERS-BLENDERS, MISCELLANEOUS
Maguire #WSB-140, gravimetric blender, 4-material type, 350-475 Lb/Hr throughput, dispense system, s/n #90426 Show photo of item Show item detail
Hoff Online Auctions, Minneapolis, MN 612-521-5500 (Fax 612-331-3291) Denny Hoff
REACTORS & KETTLES (Also See Autoclaves)
25 liter Buchi, Kilo Lab Glass lReactor System, agit.dr, glass receiver, glass coil cond, all mtd.in tublar steel frame, #48891 Show photo of item Show item detail
Federal Equipment Co, Cleveland, OH 216-271-3500 (Fax 216-271-5210) Joanne Parente
200 gal. WM Sprinkman, solution mix system, Stainless Steel, ATM int, jktd.100 psi @ 100°F to 15psi @ 250°F, A-B PLC, #48796 Show photo of item Show item detail
Federal Equipment Co, Cleveland, OH 216-271-3500 (Fax 216-271-5210) Joanne Parente
500 gal. D & W Welding Reactor, 316L Stainless Steel, 54" diameter x 54" str.side, dish top/bttm, 45 psi & FV @ 400°F int, jktd.180 psi, 1981, #48764 Show photo of item Show item detail
Federal Equipment Co, Cleveland, OH 216-271-3500 (Fax 216-271-5210) Joanne Parente
Midwest Reactor Body, 77" D x 128" str.side, NB 37, 100 psi FV @ 400° F, jacketed 200° F, 1994, #70139 Show photo of item Show item detail
Federal Equipment Co, Cleveland, OH 216-271-3500 (Fax 216-271-5210) Joanne Parente
Midwest Fab. #V-1, Stainless Steel Reactor Body, 7' D x 122'str.side, NB 67, 100 psi FV @ 400° F, 200 psi dimple jktd, 1994, #70138
Federal Equipment Co, Cleveland, OH 216-271-3500 (Fax 216-271-5210) Joanne Parente
SCREENS, VIBRATING
6" Beringer #6UL376, slide plate screen changer, 480 V., used, 1998, #8446 Show photo of item
Arlington Plastics Machinery, Elk Grove Village, IL 847-956-7300 (Fax 847-956-8585) Sales
SCREENS & SIFTERS
18" Sweco #LS18333, Stainless Steel Circular Screen, on Base, Ser. #A26673, #48850 Show photo of item Show item detail
Federal Equipment Co, Cleveland, OH 216-271-3500 (Fax 216-271-5210) Joanne Parente
TANKS (VESSELS), ALUMINUM
5000 gal., 8' diameter x 13' L, horiz.alum. tank, dished ends, 16" , (3)4" , 1" top nozzles, 1" botton outlet, on saddles, #48766 Show photo of item Show item detail
Federal Equipment Co, Cleveland, OH 216-271-3500 (Fax 216-271-5210) Joanne Parente
TANKS (VESSELS), CARBON STEEL, ATMOSPHERIC (14.7 PSI) & PRESSURIZED
400 gal. Industrial Service, Inc., C/S Receiver, 36" diameter x 96" str.side, 153 psi & FRV @ 400° F int, NB #041, 1988, #48848 Show photo of item Show item detail
Federal Equipment Co, Cleveland, OH 216-271-3500 (Fax 216-271-5210) Joanne Parente
TANKS (VESSELS), CRYOGENIC, STAINLESS, PRESSURIZED
500 gal. 48" diameter x 60" side, SS blend tank on legs, 8" dish, 139" OH, 2" center bottom outlet Show photo of item
DMBS, Houston, TX 713-847-7775 (Fax 713-847-9994) Mark Nawrot
TANKS (VESSELS), GLASS LINED, HASTELLOY, MONEL, NICKEL, STAINLESS
1 gal. Stainless Steel Receiver, 5.75" diameter x 8str.side, flat top, dish bottom, top & side nozzles, center bottom outlet w/valve, #34972 Show photo of item Show item detail
Federal Equipment Co, Cleveland, OH 216-271-3500 (Fax 216-271-5210) Joanne Parente
200 liter Allegheny Bradford #200L, Stainless Steel jktd.receiver, remov.dish top/dish bttm, 50 psi & FV @ 300°F int, jktd.100psi, #48813 Show photo of item Show item detail
Federal Equipment Co, Cleveland, OH 216-271-3500 (Fax 216-271-5210) Joanne Parente
200 liter Allegheny Bradford #200L, Stainless Steel jktd.receiver, remov.dish top/dish bttm, 50 psi & FV @ 300°F int, jktd.100psi, #48816 Show photo of item Show item detail
Federal Equipment Co, Cleveland, OH 216-271-3500 (Fax 216-271-5210) Joanne Parente
200 liter Allegheny Bradford #200L, Stainless Steel jktd.receiver, remov.dish top/dish bttm, 50 psi & FV @ 300°F int, jktd.100psi, #48815 Show photo of item Show item detail
Federal Equipment Co, Cleveland, OH 216-271-3500 (Fax 216-271-5210) Joanne Parente
200 liter Allegheny Bradford #200L, Stainless Steel jktd.receiver, remov.dish top/dish bttm, 50 psi & FV @ 300°F int, jktd.100psi, #48814 Show photo of item Show item detail
Federal Equipment Co, Cleveland, OH 216-271-3500 (Fax 216-271-5210) Joanne Parente
140 gal. Acme Indl., Hastelloy C-276 Receiver, 28" diameter x 52" str.side, 60 psi & FV @ 350° F, dish top/bottom, 1995, #48765 Show photo of item Show item detail
Federal Equipment Co, Cleveland, OH 216-271-3500 (Fax 216-271-5210) Joanne Parente
1600 gal. Stainless Steel Mix Tank, 84" diameter x66" str.side, dish top/bottom, top mtd.3HP Cleveland agit.dr, S/S shaft, 4-C/S legs, #48763 Show photo of item Show item detail
Federal Equipment Co, Cleveland, OH 216-271-3500 (Fax 216-271-5210) Joanne Parente
2000 gal. Cherry Burrell, stainless steel, sanitary mixing tank (2)
Wohl Associates Inc, Bohemia, NY 631-244-7979 (Fax 631-244-6987) Andrew Wohl
6000 gal. Wendland Mfg., Stainless Steel horiz.8' diameter x 16'str.side, dish ends, ATM @ 300° F int, (2)3" top nozzles, on saddles, 2001, #48767 Show photo of item Show item detail
Federal Equipment Co, Cleveland, OH 216-271-3500 (Fax 216-271-5210) Joanne Parente
6600 gal. Evans & Son, 316SS, vertical storage tank, #KC-1013
Equipment Recovery Corp, Willoughby, OH 440-942-3003 (Fax 440-942-8608) Kevin Klicman
8000-10000 gal. Stainless Steel #T-B6, flat top/bottom, built 2/1982, #40144 Show photo of item Show item detail
Federal Equipment Co, Cleveland, OH 216-271-3500 (Fax 216-271-5210) Joanne Parente
8500 gal. MFI Tank Fab. #T-171-T-13, Stainless Steel, 95dia.x approx.28, flat top/bottom, #70140 Show photo of item Show item detail
Federal Equipment Co, Cleveland, OH 216-271-3500 (Fax 216-271-5210) Joanne Parente
10000 gal. Cognis #T-A6, 126" x 200" str.side, possibly jacketed, flat/flat, agitated, 1993, #70146 Show photo of item Show item detail
Federal Equipment Co, Cleveland, OH 216-271-3500 (Fax 216-271-5210) Joanne Parente
10000 gal. Midwest Fab. #T-B6, 126" x 200" str.side, possibly jacketed, flat/flat, agitated, 1993, #70145 Show photo of item Show item detail
Federal Equipment Co, Cleveland, OH 216-271-3500 (Fax 216-271-5210) Joanne Parente
10000 gal. Midwest Fab. #T-14, 118" x 230" str.side, flat/flat, agitated, 1988, #70141 Show photo of item Show item detail
Federal Equipment Co, Cleveland, OH 216-271-3500 (Fax 216-271-5210) Joanne Parente
10000 gal. Stainless Steel #T-16, 118" D x 230" str.side, flat top/bottom, 1988, #40143 Show photo of item Show item detail
Federal Equipment Co, Cleveland, OH 216-271-3500 (Fax 216-271-5210) Joanne Parente
10000 gal. Midwest Fab/ #T-15, Stainless Steel Tank, 118" D x 230" str.side, flat top/bottom, 1988, #40142 Show photo of item Show item detail
Federal Equipment Co, Cleveland, OH 216-271-3500 (Fax 216-271-5210) Joanne Parente
22000 gal. Stainless Steel #OP8, 148" ID, 154" x 26' str.side, may be jktd, agitated Chemineer, 7.5HP, 56RPM, dish top/flat bttm. #70148 Show photo of item Show item detail
Federal Equipment Co, Cleveland, OH 216-271-3500 (Fax 216-271-5210) Joanne Parente
25000 gal. Stainless Steel Tank, 148" ID, 154" OD x 26' str.side, may be jktd, agitated Chemineer 7.5HP, dish top/flat bttm, #70147 Show photo of item Show item detail
Federal Equipment Co, Cleveland, OH 216-271-3500 (Fax 216-271-5210) Joanne Parente
Chemineer #83-V103, Stainless Steel Tank, 93" Dia, Chemineer agit, installed thru cement floor, 8'-10' H, #70132 Show photo of item Show item detail
Federal Equipment Co, Cleveland, OH 216-271-3500 (Fax 216-271-5210) Joanne Parente
Enpro Deaerator/Deoxygenerator, Type VT w/storage, C/S, 40000#/hr.cap, 75 psi & FV @ 450°F int, NB #11112, 1988, #48847 Show photo of item Show item detail
Federal Equipment Co, Cleveland, OH 216-271-3500 (Fax 216-271-5210) Joanne Parente
MISCELLANEOUS, CHEMICAL & PROCESSING EQUIPMENT
Siemens, UV filtration skid w/Aquafine UV light, (2)S/S pressure filters, (3)Grundfos vert.pumps, skid mtd, control.panel, #48913 Show photo of item Show item detail
Federal Equipment Co, Cleveland, OH 216-271-3500 (Fax 216-271-5210) Joanne Parente
CHILLERS (Also See Cooling Towers)
2 Ton, Air cooled water chillers, refurbished
Cold Shot Chillers, Houston, TX 281-227-8400 (Fax 281-227-8404) Mike Marrone
2 Ton, Air cooled water chillers, used
Cold Shot Chillers, Houston, TX 281-227-8400 (Fax 281-227-8404) Mike Marrone
3 Ton, Air cooled water chillers, refurbished
Cold Shot Chillers, Houston, TX 281-227-8400 (Fax 281-227-8404) Mike Marrone
10 Ton, Advantage #MK-10W-41HR, water cooled, $-22 refrigerant, 460 V., Ser. #76820, 2001, #48718 Show photo of item Show item detail
Federal Equipment Co, Cleveland, OH 216-271-3500 (Fax 216-271-5210) Joanne Parente
22 Ton, Carrier Aquasnap #30RAN022HE-615QK, air cooled, R22 refrigerant, 460 V., #48917 Show photo of item Show item detail
Federal Equipment Co, Cleveland, OH 216-271-3500 (Fax 216-271-5210) Joanne Parente
38 Ton, Carrier Aquasnap #30RAN035JS-615QM, air cooled, R22 refrigerant, 460 V., #48916 Show photo of item Show item detail
Federal Equipment Co, Cleveland, OH 216-271-3500 (Fax 216-271-5210) Joanne Parente
CNC MACHINERY & EQUIPMENT
AUTOMATIC SCREW MACHINES & CHUCKERS, INCLUDES SWISS TYPE, CNC
Tsugami #BO124, Fanuc OiTD, 4-Axis, 12k RPM, 1°, 17 tool, 2 Live/6 OD/4 ID, barfeed, '11 Show photo of item
520 Machinery Sales LLC, Schaumburg, IL 888-520-1768 (Fax 630-855-3535) Everett Dahlberg
BENDERS, BAR, PIPE & TUBE, CNC
1-1/2" Pines #040, CNC , Mandrel, pedestal op station, TS-2000 CNC, #4548
Scott Machinery & Supply Inc, Helena, AL 205-664-9644 (Fax 205-664-9796) George Scott
3" Eaton Leonard #VB300HT, CNC tube bender, auto repo, 15 HP, CW, 1998, rblt 2002, #51635 Show photo of item Show item detail
Yoder Machinery Sales, Holland, OH 800-622-4463 (Fax 419-865-5557) Sales
BORING MILLS, HORIZONTAL, Floor Type, CNC
5" K & T, 6' vert., 6'horz., 5'rotary/tilt/trunion tbl, tool chngr, Siemens 5-Ax.CNC, mint
Peterson Machinery Sales, Casa Grande, AZ 520-836-9727 (Fax 520-836-1944) Charlie Peterson
7" Giddings & Lewis #FTR-5000, ram type, 60 ATC, 137" Y, Siemens 840D, 2011
Concord Machinery, Pontiac, MI 248-335-0300 (Fax 248-335-0553) T.Hill/ Jason K.
BORING MILLS, HORIZONTAL, Table Type, CNC
4.3" Toshiba #BTD11BR3, Tosnuc 3, 79" X, 59" Y, 57" Z, 24" W, #50 tpr, 25 HP, 51" x63" r/tbl, '87 Show photo of item Show item detail
S & M Machinery Sales Inc, Warren, MI 586-755-1234 (Fax 586-755-9876) Spencer Minns
4.33" Toshiba #BTD-110R16, 5-Axis, Tosnuc 888, 98.4" X, 71" Y, 19" W, 60 ATC, chip conv, 1995 Show photo of item
Machinery Network Inc, Encino, CA 310-826-4440 (Fax 818-788-2470) Sales Dept.
5" doosan db130-cx, fanuc 18, 2009, 118" x, 79" y, 2, 500 rpm, 40 atc, cts Show photo of item Show Video of Item Show item detail
Prime Machinery Inc, Oyster Bay, NY 516-922-7977 (Fax 516-922-9691) Steve Brenner
5" doosan dbc-130l, fanuc 31, 2012, 158" x, 98" y, 79" z, 28" w, cts, 40 atc Show photo of item Show Video of Item Show item detail
Prime Machinery Inc, Oyster Bay, NY 516-922-7977 (Fax 516-922-9691) Steve Brenner
6" Union, 63" x78.75" table, 108" X, 72" Y, 62" Z, Fanuc O CNC, #5265
Scott Machinery & Supply Inc, Helena, AL 205-664-9644 (Fax 205-664-9796) George Scott
Mazak Megaturn #A-12, Mazatrol T32-2, 49.2" chuck, 57.1" swing, 16 ATC, CTS Show photo of item
Machinery Network Inc, Encino, CA 310-826-4440 (Fax 818-788-2470) Sales Dept.
BORING MILLS, VERTICAL, CNC (Including Vertical Lathes- VTL & Vertical Turning Centers)
Hankook vtc-85r, live milling, 24" hyd chuck, 35" swing, fanuc 21itb, 2010, c-axis Show photo of item Show Video of Item Show item detail
Prime Machinery Inc, Oyster Bay, NY 516-922-7977 (Fax 516-922-9691) Steve Brenner
31.5" Doosan #VT850, Fanuc 21iTB, 39.7" swg, 24" chuck, 33.46" Z, 18.5" X, under 7000 cut.hrs Show photo of item Show item detail
Concord Machinery, Pontiac, MI 248-335-0300 (Fax 248-335-0553) T.Hill/ Jason K.
66" bullard, 6-axis cnc, ram, turret, side head, siemens cnc, 78" swing, 4-jaw Show photo of item Show Video of Item Show item detail
Prime Machinery Inc, Oyster Bay, NY 516-922-7977 (Fax 516-922-9691) Steve Brenner
72" Giddings & Lewis CNC VTL, Fanuc 21i-T, 12 ATC, rebuilt 2009
L S Walker Machine Tools Inc, Milton, ON 905-876-0890 (Fax 905-876-1959) Chris Walker
Cleereman jig borer Show photo of item Show item detail
Machinesused.com, Minneapolis, MN 763-745-1166 (Fax 651-315-8176) John Lawton
Daewoo #V15-3A, live milling, Fanuc 15T, 31.5" swg, 27.5" turn, 40 HP, 15" chuck, chip conv, '98 Show photo of item
Machinery Network Inc, Encino, CA 310-826-4440 (Fax 818-788-2470) Sales Dept.
YF Industries #YVT-1600, Fanuc 0iTD, 63" chuck, 80 HP, 26500 lbs tbl load, 12 ATC, 2014 Show photo of item
Machinery Management LLC, South Elgin, IL 847-608-9300 (Fax 847-608-9301) Tom Hazelhurst
BRAKES, PRESS, CNC (Also See Brakes, Press Alphabetical Classification)
25 Ton, Coast One #C900, 34" , C1000 Graphical PLC based CNC controls, 2-Axis BG, 2014, #15850 Show photo of item Show item detail
Active Machinery Sales, Apex, NC 800-377-7553 (Fax 919-387-0096) Mike Sawaia
Toyokoki APB-3613 WU, 42 Ton, 51" , Toyokoki Am Style Punch Holders, WIlson Am Style Lower Die Holder, Elec FS, 2007, #15921 Show photo of item Show item detail
Active Machinery Sales, Apex, NC 800-377-7553 (Fax 919-387-0096) Mike Sawaia
55 Ton, Pacific #J-55, Hurco Aut-bend IV controls., 6" throat, 5 HP, 1980, #6846
Fabricating Machinery Corp, Duarte, CA 626-359-0024 (Fax 626-359-4055) Scott Courneya
99 Ton, Durma #AD-E3090, Delem DA-51 2-Axis, 10' OA, 2007, #10184 Show photo of item
Jordan Craig Machinery Intl L, New City, NY 845-398-0073 (Fax 845-398-0074) Jordan Craig
110 Ton, Amada #HFE-1003S/7, Amada Operateur, 10.2' OA, 106" BH, 2000, #10186
Jordan Craig Machinery Intl L, New City, NY 845-398-0073 (Fax 845-398-0074) Jordan Craig
123 Ton, Baileigh #BP-12313NC, Delem 2-Axis, 2008, installed new 2011, #10183 Show photo of item
Jordan Craig Machinery Intl L, New City, NY 845-398-0073 (Fax 845-398-0074) Jordan Craig
143 Ton, Amada #HDS-1303NT, AMNC-PC 8-Axis, 10.7' OA, 106.3" BH, 2003, #10185 Show photo of item
Jordan Craig Machinery Intl L, New City, NY 845-398-0073 (Fax 845-398-0074) Jordan Craig
200 Ton, Allsteel #200-12, 12', Cybelec DNC 60 CNC & BG, complete set clamps, '04, #15880 Show photo of item Show item detail
Active Machinery Sales, Apex, NC 800-377-7553 (Fax 919-387-0096) Mike Sawaia
230 Ton, Cincinnati #230AF10, 2-Axis, 12' OA, crowning, updated control, 1988, #10182
Jordan Craig Machinery Intl L, New City, NY 845-398-0073 (Fax 845-398-0074) Jordan Craig
250 Ton, HTC #250-14, 14' OA, Automec CNC 150 Autogauge control & BG, 1973, #15888 Show photo of item Show item detail
Active Machinery Sales, Apex, NC 800-377-7553 (Fax 919-387-0096) Mike Sawaia
DRILLING & TAPPING CENTERS, CNC
Fanuc Alpha T-21iE Robodrill, Fanuc 31i-A5 CNC Control, New 2006 Show photo of item
American Systems & Equipment, Chicopee, MA 413-739-8170 (Fax 413-739-7964) Mark Barowsky
ELECTRICAL DISCHARGE MACHINES (EDM), SMALL HOLE, CNC
Castek Series SD " Fast Hole" , EDM hole machine Show photo of item Show Video of Item Show item detail
Miedema Auctioneering & Appraisals Inc, Byron Center, MI 616-538-0367 (Fax 616-538-5230) Amada Bowers
ELECTRICAL DISCHARGE MACHINES (EDM), WIRE, CNC
Fanuc RoboCut Alpha C400iA, Fanuic 31i-WB, 14.6" x10.6" x10" , AWT, submerged, 2012
Machinery Network Inc, Encino, CA 310-826-4440 (Fax 818-788-2470) Sales Dept.
Mitsubishi DWC90SB, 4 Axis, CNC Wire EDM, Control G25B, 50 amp, chiller, new 1992, $7950 Show photo of item
Greasymachines.com, Bristol, CT 866-473-2796 (Fax 860-585-9072) Nick/ George
Mitsubishi #QA10, AWF, 14.8" x 20.9" table, 1999 Show photo of item
Clark Machinery Sales LLC, Hunt Valley, MD 410-252-5494 (Fax 443-269-0660) Troy Clark
FOLDING MACHINES (FOLDERS), CNC
10' x 10 ga. RAS Series 74, CNC
SMF & Machine Tools Inc, Little Rock, AR 800-643-5839 (Fax 501-897-4090) Teresa Glover
159" x 9 ga. Fasti #215-40, New Rockford CFP 120 CNC, L-shaped BG, 1995, #15899 Show photo of item Show item detail
Active Machinery Sales, Apex, NC 800-377-7553 (Fax 919-387-0096) Mike Sawaia
GEAR GENERATORS, CNC
Gleason #725, straight bevel revacycle gear generators Show photo of item Show item detail
Hilco Industrial LLC, Farmington Hills, MI 248-419-1964 (Fax 248-254-9995) Ken Planet
GEAR HOBBING MACHINERY (HOBBERS), CNC
Pfauter #P100, 5-Axis CNC gear hobbers Show photo of item Show item detail
Hilco Industrial LLC, Farmington Hills, MI 248-419-1964 (Fax 248-254-9995) Ken Planet
GEAR SHAPERS, CNC
Demm #SR250-50, gear shapers, 1999 & 2000 Show photo of item Show item detail
Hilco Industrial LLC, Farmington Hills, MI 248-419-1964 (Fax 248-254-9995) Ken Planet
Fellows #10-2, gear shapers Show photo of item Show item detail
Hilco Industrial LLC, Farmington Hills, MI 248-419-1964 (Fax 248-254-9995) Ken Planet
GEAR SHAVERS, CNC
Hurth #ZS240T, CNC gear shavers Show photo of item Show item detail
Hilco Industrial LLC, Farmington Hills, MI 248-419-1964 (Fax 248-254-9995) Ken Planet
GRINDERS, CYLINDRICAL, CNC
13" x 25" Okuma #GU34S, OSP500G CNC, 8" mag.chk, 15.9" x1.97" x5" whl, .87" bore, clnt, '96 Show photo of item Show Video of Item Show item detail
Adams Machinery Co, Lincolnwood, IL 847-673-0556 (Fax 847-673-7636) Sonneborn
GRINDERS, CYLINDRICAL, ANGLE HEAD, CNC
24" x 40" Cincinnati #480, Fanuc OG, 30" wheel, flagging, 1998, #6774
Scott Machinery & Supply Inc, Helena, AL 205-664-9644 (Fax 205-664-9796) George Scott
GRINDERS, SURFACE, CNC
42" x 36" Thompson #12PCX, MCM Series CNC, 42" x144" mag.chuck, 40 HP, 1972 Show photo of item
Bayshore Industrial Sales Inc, Grosse Pointe, MI 313-881-2120 (Fax 313-881-4855) Eric Hoffman
GRINDERS, SURFACE, ROTARY TABLE, (VERTICAL SPINDLE), CNC
SMW #RT-250, programmable 4th Axis indexer w/System 45 controller Show photo of item Show item detail
Machinesused.com, Minneapolis, MN 763-745-1166 (Fax 651-315-8176) John Lawton
LASERS, CNC (Also See Plasma Cutters/Punches, CNC)
Amada Gemini #FO3015, 4000 watt, 60" x 120" cutting area, chiller, 2004
Johnston Machinery Corp, Des Plaines, IL 847-803-8700 (Fax 847-803-8701) Brian Johnston
Amada Gemini FO3015, 4000 Watt, 5' x 10' Dual Pallet Shuttle Tbls, Non-Contact Auto Focus Cutting Head, Chiller, '02, #15918 Show photo of item Show item detail
Active Machinery Sales, Apex, NC 800-377-7553 (Fax 919-387-0096) Mike Sawaia
Amada Gemini #FO3015, 4000 watt, 5' x10'dual pallet shuttle tbls, chiller, 2000, #15911 Show photo of item Show item detail
Active Machinery Sales, Apex, NC 800-377-7553 (Fax 919-387-0096) Mike Sawaia
Bystronic Bystar #3015, 6000 watt, 120" x 60" , 2011
Machinery Management LLC, South Elgin, IL 847-608-9300 (Fax 847-608-9301) Tom Hazelhurst
Bystronic Bystar #3015-3, 4400 watt, 5' x10'dual pallet shuttle tbls, chiller, '06, #15900 Show photo of item Show item detail
Active Machinery Sales, Apex, NC 800-377-7553 (Fax 919-387-0096) Mike Sawaia
Cincinnati #CL707, 2000 watt, 5' x10'dual pallet shuttle tbls, chiller unit, 1997, #15897 Show photo of item Show item detail
Active Machinery Sales, Apex, NC 800-377-7553 (Fax 919-387-0096) Mike Sawaia
Mazak #FG150, 4000 watt, 6" , 3D cutting head, touch probe, auto power off, 2005, #15901 Show photo of item Show item detail
Active Machinery Sales, Apex, NC 800-377-7553 (Fax 919-387-0096) Mike Sawaia
Mazak Super Tubo #X 510, 1500 watt C02 laser, 1991 Show photo of item Show item detail
Machine Tool Technologies, Milwaukee, WI 414-486-9700 (Fax 414-769-1522) Joe Ryan
Mazak Super Turbo X Hi Pro #48, 2000 watt C02 laser, 1993 Show photo of item
Machine Tool Technologies, Milwaukee, WI 414-486-9700 (Fax 414-769-1522) Joe Ryan
Mazak Super Turbo X Hi Pro #510, 2000 watt C02 laser, 1993 Show photo of item Show item detail
Machine Tool Technologies, Milwaukee, WI 414-486-9700 (Fax 414-769-1522) Joe Ryan
Mitsubishi #3015HVP, 2000 watt, 5' x10'dual pallet shuttle tbls, chiller unit, '07, #15915 Show photo of item Show item detail
Active Machinery Sales, Apex, NC 800-377-7553 (Fax 919-387-0096) Mike Sawaia
Mitsubishi #LVP-3015 Plus, 4000 watt, 5' x10', non contact cutting hd, chiller, '05, #15905 Show photo of item Show item detail
Active Machinery Sales, Apex, NC 800-377-7553 (Fax 919-387-0096) Mike Sawaia
Mitsubishi #LVP-3015 Plus II, 4000 watt, 5' x10', non contact cutting head, 2008, #15906 Show photo of item Show item detail
Active Machinery Sales, Apex, NC 800-377-7553 (Fax 919-387-0096) Mike Sawaia
Tanaka #LMXV-Z30, Fanuc TF6000E, 6000 watt, 10' x 30'travels, Fanuc 16iLB, 2004, #24960 Show photo of item Show item detail
Prestige Equipment Corp, Melville, NY 631-249-5566 (Fax 631-249-9494) Frank DiSalvo
Trumpf Trulaser #7000, 3600 watt, 10" round cap, 30' infeed, 20'outfeed, 2009, #15895 Show photo of item Show item detail
Active Machinery Sales, Apex, NC 800-377-7553 (Fax 919-387-0096) Mike Sawaia
2000 Watt Cincinnati CL-707, X-96" , Y-48" , Linear Drives, Pallet Changer, 1998, #24981 Show photo of item
Prestige Equipment Corp, Melville, NY 631-249-5566 (Fax 631-249-9494) Frank DiSalvo
2000 Watt Mitsubishi 3105 LXP, 60" x 120" , ML3020 Resontor, Dual Pallets, 1998, #24982 Show photo of item Show item detail
Prestige Equipment Corp, Melville, NY 631-249-5566 (Fax 631-249-9494) Frank DiSalvo
LATHES, CHUCKING, CNC
Fuji #FS4-3100, Fanuc 0iTD, Fanuc L35-08H robot, chip auger, 2011 Show photo of item
Machinery Management LLC, South Elgin, IL 847-608-9300 (Fax 847-608-9301) Tom Hazelhurst
Mazak Quick Turn #25C, 2-Axis CNC chucker lathe, 1998 Show photo of item Show item detail
R & J Machinery Sales, Milford, MI 248-685-7879 (Fax 248-676-0389) Jeff Bruce
Mori-Seiki #CL-203B, CNC turning center, extremely compact CL Series, 1999 Show photo of item Show item detail
Industrial Machinery NJ, LLC, Livonia, MI 732-367-4130 (Fax 732-719-4761) Tuli Simcha
Romi #G30, GE Fanuc, tlstk, 10" chuck, tool presetter, 12" x40" cut.cap, 3k RPM, 2.5" bar cap, '99 Show photo of item Show item detail
Vander Ziel Machinery Sales, Alto, MI 616-868-1111 (Fax 616-868-1115) Steve Vander Ziel
LATHES, COMBINATION, CNC Turning Centers
Amera-Seiki #S-38C, C-axis, livetooling, 24" ck, 6.5" bar, 35" sw, 118' cc, 50hp/10hp, 0i-TD, '13 Show photo of item Show item detail
Amera-Seiki Corp., Hiawatha, IA 319-730-0326 (Fax 319-377-3035) Brad Pekerik
Cincinnati Hawk #250, Siemens Acra 2100 CNC, 21" swg, 3-Jaw 10" chuck, tlstk w/27" cc, '99 Show photo of item
Great American Eqpt Co, Cincinnati, OH 513-771-2111 (Fax 513-771-2552) Sales Dept.
COLCHESTER, FANUC 20-T, 12" Chk, 1995, CNC/MANUAL FLAT BED, 21.5" SWING, 32" GAP, 80" CC Show photo of item Show Video of Item Show item detail
Prime Machinery Inc, Oyster Bay, NY 516-922-7977 (Fax 516-922-9691) Steve Brenner
1995 Daewoo Puma 12L-C - 4.6" Bar, 15" Chuck, 2, 000 RPM, 40 HP, 1995 Show photo of item Show Video of Item Show item detail
ReSell CNC, Maitland, FL 407-478-8181 (Fax 407-478-1149) John Butz
Daewoo Puma #250B, Mits 520L, 22.4" sw, 27.2" cc, 3.5" bore, 3500 RPM, 10 tool, 10" chuck, '97 Show photo of item
520 Machinery Sales LLC, Schaumburg, IL 888-520-1768 (Fax 630-855-3535) Everett Dahlberg
Daewoo Puma #250LBX, Fanuc control, 30 HP, 3000 RPM, 4" spindle bore, 10" hyd.chuck, 1998 Show photo of item Show item detail
Wheeler Machinery Sales, Pomona, CA 888-589-6721 (Fax 909-348-5617) Dan Wheeler
Daewoo Puma #8, Fanuc 10T, 17.7" sw, 2" bar, 14" length, 4k RPM, 20 HP, 8" chuck, 12 tool, tlstk, '87 Show photo of item
520 Machinery Sales LLC, Schaumburg, IL 888-520-1768 (Fax 630-855-3535) Everett Dahlberg
Daewoo Lynx #210C, 20" swg, 11" length, 12-turret, 4500 RPM, Fanuc I-Series, 2002, S33634 Show photo of item Show item detail
Perfection Machinery Sales, Elk Grove Village, IL 847-427-3333 (Fax 847-427-8884) Sales Dept.
Doosan Daewoo Puma #240M, Fanuc 21iT, 3-Axis, 21.6" swing, 3500 RPM, tailstock, live tooling, sub spindle, 2006, #L2150139 Show photo of item Show item detail
N & R Machine Sales, Navasota, TX 800-245-3194 (Fax 936-825-2679) Randy Nevels
Doosan Puma #2100SY, Fanuc, 30" sw, 2.6" bar, 5k RPM, 12 tool, full C, Y-Axis, sub spdl, '11 Show photo of item
520 Machinery Sales LLC, Schaumburg, IL 888-520-1768 (Fax 630-855-3535) Everett Dahlberg
Doosan Puma #3100-LY, 2011
Cities Advanced Machinery, Eden Prairie, MN 952-944-6060 (Fax 952-944-0043) Harry Youtsos
Haas #HL-1, 20" swing, 20" length, 2" bar, 8" chuck, 3750 RPM, 15 HP, 10 tool, QC, R/T, 1997 Show photo of item
520 Machinery Sales LLC, Schaumburg, IL 888-520-1768 (Fax 630-855-3535) Everett Dahlberg
Haas #SL-20T, Haas CNC, 8" chuck, Servo Bar 300 Mag.BF, 10 sta.trrt, tlstk, low hrs, 2006 Show photo of item Show item detail
Precision Machinery Sales Inc, Elk River, MN 763-370-7460 Matt Klein
Haas #SL-30T, 30" sw, 39" cc, 3" bar, 10" chuck, 3400 RPM, 12 tool, QC, auger, tlstk, presetter, '04 Show photo of item
520 Machinery Sales LLC, Schaumburg, IL 888-520-1768 (Fax 630-855-3535) Everett Dahlberg
Haas #SL-30T, Haas, 10" chuck, 3" , tailstock, chip auger, spindle orientation, 1999 Show photo of item Show item detail
Automatics & Machinery Co Inc, Longmont, CO 800-543-7666 (Fax 303-651-6556) Steve Beck
Haas #ST-20, 2" bar, 10" chuck, 4000 RPM, 20 HP, 12 tools, 2012 Show photo of item Show item detail
ReSell CNC, Maitland, FL 407-478-8181 (Fax 407-478-1149) John Butz
Haas #ST-30BB, 4" bore, 12" chuck, 30" centers, live tooling, Big Bore, 2011 Show photo of item Show item detail
ReSell CNC, Maitland, FL 407-478-8181 (Fax 407-478-1149) John Butz
Hitachi Seiki #HT-23SII, Seiki Multi, 15" swing, 10" 3-Jaw chuck, #5MT, 2.5" bar, tailstock, s/n #HTS-2909, 20 HP, #153697 Show photo of item Show item detail
Machinery Values Inc, Harrison, NJ 973-497-7540 (Fax 973-497-7541) Mike DeRisi
Hyundai Kia SKT-210SY, FANUC 21i-T, 8" Chk, 2006, Y-Axis, Sup Spindle, Live Tool Show photo of item Show item detail
Automatics & Machinery Co Inc, Longmont, CO 800-543-7666 (Fax 303-651-6556) Steve Beck
Kia #SKT-200, Fanuc Oi-T, 8" chuck, 12 ATC, Qwik-Tech barfeed, chip, 2008
Lee Stevens Machinery Inc., Wixom, MI 248-926-8400 (Fax 248-926-8499) Randy/ Jeff/Chris
Mazak Integrex, CNC turning sub-turret, Mazatrol Matrix, 33.5" sw., 60" center, 40 HP, '07
Cities Advanced Machinery, Eden Prairie, MN 952-944-6060 (Fax 952-944-0043) Harry Youtsos
Mazak Integrex #i-100S, 2" bar, 6" chuck, 6k RPM, 5-Axis, twin spindle, 2013 Show photo of item Show item detail
ReSell CNC, Maitland, FL 407-478-8181 (Fax 407-478-1149) John Butz
Mazak #M5N, Mazatrol T-Plus, 24" swing, 3-Jaw 18" chuck, 1997, #7017
Scott Machinery & Supply Inc, Helena, AL 205-664-9644 (Fax 205-664-9796) George Scott
Mazak #M-5N, Mazatrol 640T, 22.1" X, 80.9" Z, 5.1" W, 4.1" spdl bore, 24" swg, 24" chuck, SR, 2007 Show photo of item
Machinery Network Inc, Encino, CA 310-826-4440 (Fax 818-788-2470) Sales Dept.
Mazak Multiplex #6100, Maz. Fusion 640T, 40" centers, C-axis, 6k RPM, 20 HP, '02
Cities Advanced Machinery, Eden Prairie, MN 952-944-6060 (Fax 952-944-0043) Harry Youtsos
Mazak Multiplex #620 Mark II, Maz. T-plus, 15.3" sw., 46" btwn.spindles, 25 HP, '98
Cities Advanced Machinery, Eden Prairie, MN 952-944-6060 (Fax 952-944-0043) Harry Youtsos
MAZAK MULTIPLEX 6200, FUSION 640T, 8" Chk, 2" , 2005, LIVE MILLING, LNS BAR FEEDER Show photo of item Show item detail
Prime Machinery Inc, Oyster Bay, NY 516-922-7977 (Fax 516-922-9691) Steve Brenner
Mazak multiplex 6200y twin spindle cnc lathe & mill center w/gl-150 gantry Show photo of item Show item detail
Prime Machinery Inc, Oyster Bay, NY 516-922-7977 (Fax 516-922-9691) Steve Brenner
Mazak Nexus #250, Matrix control, 10" chuck, chip conveyor, low hours, 2008 Show photo of item
Winslow's Machine Tool Sales, Lexington, TN 731-614-1296 (Fax 731-968-8976) Don Winslow
Mazak Nexus #QTN200, 24.02" swing, 2002, #78242 Show photo of item
Machinery Resources Intl, Simi Valley, CA 818-346-7985 (Fax 818-346-7986) Sales Dept.
Mazak qt nexus 200-ii, nexus, 2006, chip conveyor, 8" chuck Show photo of item Show item detail
Prime Machinery Inc, Oyster Bay, NY 516-922-7977 (Fax 516-922-9691) Steve Brenner
Mazak qt nexus 200-ii, nexus, 2010, chip conv, bar feeder, chip conveyor Show photo of item Show item detail
Prime Machinery Inc, Oyster Bay, NY 516-922-7977 (Fax 516-922-9691) Steve Brenner
Mazak qt100, 2007, mazatrol matrix, 6" chuck, *2 identical machines available* Show photo of item Show item detail
Prime Machinery Inc, Oyster Bay, NY 516-922-7977 (Fax 516-922-9691) Steve Brenner
Mazak #QT300, Mazatrol PC 640T Fusion, 165.1" turn.dia., 12" chuck, 3" bore, chip conv, 2001 Show photo of item
Machinery Network Inc, Encino, CA 310-826-4440 (Fax 818-788-2470) Sales Dept.
Mazak #QTN-200, 2-Axis, Mazatrol 640T Nexus, 24" swg, 20.2" turn.lgth, 8" chuck, tlstk, 2006 Show photo of item
Machinery Network Inc, Encino, CA 310-826-4440 (Fax 818-788-2470) Sales Dept.
Milltronics #TL15, Centroid 7, 8" Chk, 0-3000 rpm, 15" Sw, 40" CC, #6973
Scott Machinery & Supply Inc, Helena, AL 205-664-9644 (Fax 205-664-9796) George Scott
Monarch Model220 Fanuc 15TA, 36" swing, 130" center, 24" chuck, Tail, Chip, Steady, X axis scale, Cool, 7-7/16 bore, 75 HP, 97 Show photo of item
Spier Machinery Corp, North Tonawanda, NY 716-694-4711 (Fax 716-694-0627) Paul Shear
Mori-Seiki #NL-1500SY, MSX-850III, G Loader, 8" chuck, 6" sub-chuck, 6k RPM, 2004, #34444 Show photo of item
Machinery Network Inc, Encino, CA 310-826-4440 (Fax 818-788-2470) Sales Dept.
Mori-Seiki #SL-15, 17.7" sw, Kitagawa 3-Jaw 6.5" chuck, Moric-T6F Fanuc 16T, 6000RPM, '93, #9658
Wisconsin Metalworking Machinery, Waukesha, WI 262-548-6080 (Fax 262-548-6094) J.R. Kraemer
Mori-Seiki #SL-3H, Yasnac CNC, 3-jaw 10" chuck, 10 tools, tlstk, orig.job shop running, '82
J Hebert Machine Tool Co., Charlotte, NC 704-825-1511 Jon Hebert
Mori-Seiki #SL-75A, MSC-516 (Fanuc 18T), 2-Axis, 4-jaw 21" chuck, 21" swing, 1010 RPM, tailstock, 1996, #L2150141 Show photo of item Show Video of Item Show item detail
N & R Machine Sales, Navasota, TX 800-245-3194 (Fax 936-825-2679) Randy Nevels
Mori-Seiki #ZL25B-1000, 4-Axis CNC turning centers Show photo of item Show item detail
Hilco Industrial LLC, Farmington Hills, MI 248-419-1964 (Fax 248-254-9995) Ken Planet
Okuma Captain 370L, E100L 10" chuck, collet chuck, LNS bar feed, chip, part catch, tailstock, 6400 hrs.run, 01 Show photo of item
Spier Machinery Corp, North Tonawanda, NY 716-694-4711 (Fax 716-694-0627) Paul Shear
Okuma #L1420, OSP 700L, 24" sw, 26" length, 4.3" bore, 2800 RPM, 12 tool, chip conv, 12" chuck, '97 Show photo of item
520 Machinery Sales LLC, Schaumburg, IL 888-520-1768 (Fax 630-855-3535) Everett Dahlberg
Okuma-Howa #ACT 2SP V3, VTL, 20" swing, 13.78" X, 16.14" Z, 23.62" cc, 12 turret, 1995 (2) Show photo of item Show Video of Item Show item detail
R & J Machinery Sales, Milford, MI 248-685-7879 (Fax 248-676-0389) Jeff Bruce
Poreba #TFP93N, Fanuc 18T, 118" centers, 24" chuck, 8 ATC, 12.5" hole, chip, 1994
Lee Stevens Machinery Inc., Wixom, MI 248-926-8400 (Fax 248-926-8499) Randy/ Jeff/Chris
SWI #TRL-1840, 18.5" swing, 40.25" cc, 2.36" spdl hole, MT-6, 10 HP, LX3 CNC, 8" chuck, 2000 Show photo of item Show item detail
R & J Machinery Sales, Milford, MI 248-685-7879 (Fax 248-676-0389) Jeff Bruce
Warner & Swasey #SC28, Fanuc 0T, 2-Axis, 4-jaw 24" chuck, 21" swing, 851 RPM, 5 sta.turret, retrofitted, 1982, #L2150133 Show item detail
N & R Machine Sales, Navasota, TX 800-245-3194 (Fax 936-825-2679) Randy Nevels
Warner & Swasey #SC28, Fanuc 0T, 4-jaw 24" chuck, 32" swing, 5 sta.turret, retrofitted, 1982, #L2150105 Show item detail
N & R Machine Sales, Navasota, TX 800-245-3194 (Fax 936-825-2679) Randy Nevels
YCM GT-300A, 23.6" Swing, 35" Centers, Fanuc CNC, Live Milling, Probe, 2008, #24986 Show photo of item Show item detail
Prestige Equipment Corp, Melville, NY 631-249-5566 (Fax 631-249-9494) Paul Lashin
YCM Supermax #TC-15, Fanuc OT, 6" chuck, 16" swing, 5k RPM, tailstock, chip conv, #L21503 Show photo of item Show Video of Item Show item detail
N & R Machine Sales, Navasota, TX 800-245-3194 (Fax 936-825-2679) Randy Nevels
YCM Supermax #TC-15, Fanuc OT, 6" chuck, 16" swing, 5k RPM, tailstock, 12 pos.turret, chip conv, 1997, #L2150129 Show photo of item Show Video of Item Show item detail
N & R Machine Sales, Navasota, TX 800-245-3194 (Fax 936-825-2679) Randy Nevels
LATHES, ENGINE (SHAFT), CNC
16" x 30" Haas #TL-1, flatbed lathe, 8" 3-jaw, 2.31" bore, 1800 RPM, 7.5 HP, tlstk, clnt, '09 Show photo of item Show item detail
S & M Machinery Sales Inc, Warren, MI 586-755-1234 (Fax 586-755-9876) Spencer Minns
18" x 40" Trak TRL 1840 CSS, LX3 control, Constant Surface Spd, 8 Pos SmartDex Turret, Chucks, 2000 Show photo of item Show item detail
A Green Co Inc, Worcester, MA 508-791-6800 (Fax 508-791-6838) Harvey Green
LATHES, TURRET, CNC (Also See Boring Mills, Vertical, CNC)
Fuji #FS4-31G1, 2-Axis CNC lathes Show photo of item Show item detail
Hilco Industrial LLC, Farmington Hills, MI 248-419-1964 (Fax 248-254-9995) Ken Planet
Takamatsu #X200, dual spindle CNC lathes, 2004 Show photo of item Show item detail
Hilco Industrial LLC, Farmington Hills, MI 248-419-1964 (Fax 248-254-9995) Ken Planet
MACHINING CENTERS, GANTRY TYPE, CNC
Hartford #HEP-2150, Fanuc oi-MD, 78.7' x118'tbl, 88.58'x60" x29.52'trvls, 6k RPM, CTS, 2012 Show photo of item
Machinery Works Inc, Saukville, WI 262-284-5611 (Fax 262-284-5613) Adam Wescott
Shin Nippon Koki #HF-4PK, 157 x 79 x 51, 157x79 table, 33000 lb.load, Fanuc 12M, #5261
Scott Machinery & Supply Inc, Helena, AL 205-664-9644 (Fax 205-664-9796) George Scott
MACHINING CENTERS, HORIZONTAL, CNC Mills
Anayak #HVM-H-3300, large capacity 4-Axis HMC, 106" X, 78" Y, 47" Z, #1905 Show photo of item Show Video of Item Show item detail
Charleston Annex Corporation, Indian Trail, NC 704-821-7370 (Fax 704-821-7392) Lance/ Mark
Daewoo #DHP-630, Fanuc 16iMB, twin 24" pallets, 12k RPM, 40 HP, Cat 50, 60 ATC, 2001 Show photo of item
Machinery Network Inc, Encino, CA 310-826-4440 (Fax 818-788-2470) Sales Dept.
Doosan #HP4000, Fanuc 31i-A, 15.7" pllt, 23.6x22x23.6" , 14k RPM, CT40, 60 ATC, TSC, 1°, '08 Show photo of item
520 Machinery Sales LLC, Schaumburg, IL 888-520-1768 (Fax 630-855-3535) Everett Dahlberg
Enshu #GE460H, (2) 15.75" pallets, 15000 RPM, 3500 ipm rapid, Fanuc 31, 2012 Show photo of item Show item detail
R & J Machinery Sales, Milford, MI 248-685-7879 (Fax 248-676-0389) Jeff Bruce
Enshu #J40H, 4-Axis CNC horizontal machining centers Show photo of item Show item detail
Hilco Industrial LLC, Farmington Hills, MI 248-419-1964 (Fax 248-254-9995) Ken Planet
Haas #EC-400-4AX, 20" X, 20" Y, 20" Z, full 4th, 12k RPM, TSC, probing, 40 ATC, 2006 Show photo of item
Clark Machinery Sales LLC, Hunt Valley, MD 410-252-5494 (Fax 443-269-0660) Troy Clark
Makino #A51, 4-Axis, Fanuc Pro 5, 22" X/Y, 19.7" Z, (2)15.7" pllts, 14k RPM, Cat 40, 60 ATC, '07 Show photo of item
Machinery Network Inc, Encino, CA 310-826-4440 (Fax 818-788-2470) Sales Dept.
Makino #A71, 4-Axis, Fanuc Pro 5, 28.7" X, 31.5" Y, 40" Z, (2)19.7" pllts, 10k RPM, Cat 50, 2007 Show photo of item
Machinery Network Inc, Encino, CA 310-826-4440 (Fax 818-788-2470) Sales Dept.
Makino #A81, 4-Axis, Fanuc Pro 5, 35.4x31.5x35.4" , (2)24.8" pllts, 10k RPM, chip conv, '07 Show photo of item
Machinery Network Inc, Encino, CA 310-826-4440 (Fax 818-788-2470) Sales Dept.
Makino #A81, Fanuc Pro 5, 35.4x31.5x35.4" , (2)24.8" pllts, 10k RPM, Cat 50, chip conv, '08 Show photo of item
Machinery Network Inc, Encino, CA 310-826-4440 (Fax 818-788-2470) Sales Dept.
Makino #A88, Pro 3 Fanuc, 35.4" X, 31.5" Y, 38.2" Z, 40 ATC, 24.8" pallet, rigid tapping, s/n #72-MC000549, 40 HP, 2000, #13803-N
Hildebrand Machinery Co Inc, York, PA 717-846-2600 (Fax 717-845-9497) Dave Hildebrand
Matsuura #MC700H-50-PC2S, Fanuc 15M, 29.5" X, 24" Y, 25" Z, (2)19.7" pllts, 1°indexing, 50 ATC Show photo of item
Machinery Network Inc, Encino, CA 310-826-4440 (Fax 818-788-2470) Sales Dept.
Matsuura #MC900H-63-PC2S, 4-Axis, Fanuc 15M, 36.2" X, 28.3" Y, 30" Z, (2)24.8" pllts, 50 ATC Show photo of item
Machinery Network Inc, Encino, CA 310-826-4440 (Fax 818-788-2470) Sales Dept.
Mazak #FH480, M-Plus, 22.04" X/Y, 22.07" Z, 12k RPM, CAT 40, 20 HP, 1999, #M5347 Show photo of item Show item detail
S & M Machinery Sales Inc, Warren, MI 586-755-1234 (Fax 586-755-9876) Spencer Minns
Mazak Nexus #HCN6000, 4-Axis, Fusion 640M, 31.5" X/Y/Z, (2)19.7" pllts, 10k RPM, 60 ATC, '05 Show photo of item
Machinery Network Inc, Encino, CA 310-826-4440 (Fax 818-788-2470) Sales Dept.
Niigata #SPN901, 4-Ax, 59" X, 51" Y, 46" Z, 32" pllts, 126 ATC, 60 HP, probe, F30iMD, 2008, #24882 Show photo of item Show item detail
Prestige Equipment Corp, Melville, NY 631-249-5566 (Fax 631-249-9494) Paul Lashin
Okuma #MAB-80H, 5-Axis horizontal machining center, 2004
Gibbs Machinery Co, Warren, MI 586-755-5353 (Fax 586-755-0304) Sales Dept.
Starrag Heckert #CWK-500D, Fanuc 160Mi, 30" X, 30" Y, 3" Z, 120 ATC, 43 HP, 15k RPM, 2004 Show photo of item
Altman Machinery Co, Chicago, IL 773-247-4343 (Fax 773-247-2666) Howard /Steve
Tarus #HS-8412/54, 5-Axis high speed dual column CNC mill Show photo of item Show Video of Item Show item detail
Miedema Auctioneering & Appraisals Inc, Byron Center, MI 616-538-0367 (Fax 616-538-5230) Amada Bowers
Toyoda #FA400, Fanuc 16M, twin 15.7" pallets, Cat 40, 30 HP, 19.7" x18.7" x23" , 40 ATC, 1°, '99
Machinery Network Inc, Encino, CA 310-826-4440 (Fax 818-788-2470) Sales Dept.
20" x, 20" y, 20" z, haas ec-400pp, 2008, 6 pallets, 8, 000 rpm, 70 atc, cts Show photo of item Show Video of Item Show item detail
Prime Machinery Inc, Oyster Bay, NY 516-922-7977 (Fax 516-922-9691) Steve Brenner
2974, Yasda, H40i 5-Axis, CNC Horiz. Mach. Cntr., 2005 Show photo of item
Kaste Industrial Machine Sale, Enfield, CT 860-623-5700 (Fax 860-654-0548) Brad
MACHINING CENTERS, VERTICAL, CNC Mills
Brother #TC-229, 10k RPM, BT30, 16.5x11.8x9.8" , 10 ATC, 23.5" x12" tbl, Unist Mist unit, '95 Show photo of item Show item detail
Vander Ziel Machinery Sales, Alto, MI 616-868-1111 (Fax 616-868-1115) Steve Vander Ziel
Brute #8748V, Glass Scales Numatix CNC, 89.5" x39" x39" , 8k RPM, 24 ATC, 2000 Show photo of item
Bayshore Industrial Sales Inc, Grosse Pointe, MI 313-881-2120 (Fax 313-881-4855) Eric Hoffman
Chevalier #1418VMC, 18" x14" x15" trvls, Siemens Sinumerik 802D control, ATC, CT40
Advanced Jones Machinery Co, Dayton, OH 937-278-7337 (Fax 937-278-8234) Bob Gibson
Daewoo #DMV-650, Fanuc 18M, 55" x27.6" tbl, 49.6" x25.6" x22.9" , 6k RPM, CTS, new spdl, 1998 Show photo of item
Machinery Works Inc, Saukville, WI 262-284-5611 (Fax 262-284-5613) Adam Wescott
Defiance / Creative Evolution Controls high speed CNC machining center Show photo of item Show item detail
Miedema Auctioneering & Appraisals Inc, Byron Center, MI 616-538-0367 (Fax 616-538-5230) Amada Bowers
Doosan Daewoo #DMV-3016, CNC VMC, Fanuc 0iMB, 32.2" X, 16.1" Y, 20.1" Z, 24 ATC, 8000 RPM, 2007, #M018547 Show photo of item Show item detail
N & R Machine Sales, Navasota, TX 800-245-3194 (Fax 936-825-2679) Randy Nevels
Enshu #EV-650, CNC vertical machining center, #50 taper Show photo of item Show item detail
Machinesused.com, Minneapolis, MN 763-745-1166 (Fax 651-315-8176) John Lawton
Fadal #4020, 88HS CNC, 4th & 5th axis table, 10k RPM, 21 ATC, 1995
Lee Stevens Machinery Inc., Wixom, MI 248-926-8400 (Fax 248-926-8499) Randy/ Jeff/Chris
Fadal #8030, 4th & 5th axis table, 10k RPM, 30 ATC option, 1998
Lee Stevens Machinery Inc., Wixom, MI 248-926-8400 (Fax 248-926-8499) Randy/ Jeff/Chris
Fadal VMC 4525HT, 32MP control, 24 Side Mount ATC, V300 Fadal 12" Rotary Table, 10, 000rpm, New 2004 Show photo of item
PTS Machinery, Irvine, CA 949-246-2978 (Fax 888-736-4516) Gary Coleman
Fadal #VMC2216FX, Fanuc Oi-MC, 39" x16" table, 21 ATC, 10k RPM, 15/22 HP, 2007 #9750 Show photo of item Show item detail
Turner Industries Inc, Grand Rapids, MI 616-949-5910 (Fax 616-949-3461) Jeff/Bill/David
Fadal #VMC4525, MP, 45" X, 25" Y, 32" Z, 10k RPM, CT40, 24 side mount ATC, 30 HP, RT, auger, '02 Show photo of item Show item detail
S & M Machinery Sales Inc, Warren, MI 586-755-1234 (Fax 586-755-9876) Spencer Minns
Fadal #VMC6030, Fadal 88HS CNC, 60" x30" x30" , 10k RPM, 69.5" x30" tbl., 21 ATC, '98 Show photo of item
Bayshore Industrial Sales Inc, Grosse Pointe, MI 313-881-2120 (Fax 313-881-4855) Eric Hoffman
Fadal #VMC8030, Fadal 32mp CNC, 80" x30" x30" , 82.45" x30" tbl., 10k RPM, 21 ATC, '04 Show photo of item
Bayshore Industrial Sales Inc, Grosse Pointe, MI 313-881-2120 (Fax 313-881-4855) Eric Hoffman
Fanuc Robodill a-T21iF 4-Axis, Fanuc 31iA5, 19.7" x15.8" x12.9" , 24k RPM, 21 ATC, 2008 Show photo of item
Machinery Network Inc, Encino, CA 310-826-4440 (Fax 818-788-2470) Sales Dept.
Fanuc RoboDrill 4, Fanuc 16iM, 10k RPM, 14 ATC, 2002
Machinery Network Inc, Encino, CA 310-826-4440 (Fax 818-788-2470) Sales Dept.
Fanuc RoboDrill 4-Axis, Fanuc 16iM, 10k RPM, 14 ATC, 2002
Machinery Network Inc, Encino, CA 310-826-4440 (Fax 818-788-2470) Sales Dept.
Fanuc RoboDrill a-T21iE, Fanuc 31iA5, 19.7" x 15.8" x 12.9" , 10k RPM, 2007 Show photo of item
Machinery Network Inc, Encino, CA 310-826-4440 (Fax 818-788-2470) Sales Dept.
Fanuc RoboDrill a-T21iEL, Fanuc 31iA5, 27.6" x 15.7" x 13" , 24k RPM, 21 ATC, 2008 Show photo of item
Machinery Network Inc, Encino, CA 310-826-4440 (Fax 818-788-2470) Sales Dept.
Fanuc Robodrill #a-T21iEL-PC2, 27.5" X, 15.7" Y, 12.9" Z, 24k RPM, TSC, 21 ATC, 2007 Show photo of item
Clark Machinery Sales LLC, Hunt Valley, MD 410-252-5494 (Fax 443-269-0660) Troy Clark
Fanuc RoboDrill Mate, Fanuc 0iMC, 16.1" x 12.2" x 13" , 10k RPM, 14 ATC, BT-30, 2007 Show photo of item
Machinery Network Inc, Encino, CA 310-826-4440 (Fax 818-788-2470) Sales Dept.
Fanuc RoboDrill T21iE, Fanuc 31iA5, 19.7" x 15.8" x 12.9" , 10k RPM, 21 ATC, 2007 Show photo of item
Machinery Network Inc, Encino, CA 310-826-4440 (Fax 818-788-2470) Sales Dept.
Fanuc Robodrill T21iFla, options, Fanuc DDR 260i, 4th dr & interface, 219 hrs, 2012 Show photo of item Show item detail
Pacific Machine Tools LLC, Carlsbad, CA 760-431-3560 (Fax 760-431-3562) Maury Cohn
Feeler #VMP-100, Fanuc0i-MD, 43.3" x 24" x 23.6" , 10k RPM, 25 HP, #40 taper, 30 ATC, 2012 Show photo of item
Machinery Network Inc, Encino, CA 310-826-4440 (Fax 818-788-2470) Sales Dept.
Haas VF2 - 30" x16" x20" , 7, 500 RPM, CAT 40, 20 HP, 1999 Show photo of item Show Video of Item Show item detail
ReSell CNC, Maitland, FL 407-478-8181 (Fax 407-478-1149) John Butz
Haas #VF-2SS, 36x14" , 30x16x20" , 12k RPM, CT40, 24 SM ATC, 4th ready, P cool, probe, R/T, '07 Show photo of item
520 Machinery Sales LLC, Schaumburg, IL 888-520-1768 (Fax 630-855-3535) Everett Dahlberg
Haas #VF-3, 40" X, 20" Y, 25" Z, 18" x48" table, 40 taper, ATC, 2002, #7024
Scott Machinery & Supply Inc, Helena, AL 205-664-9644 (Fax 205-664-9796) George Scott
Haas #VF-3D, 40" X, 20" Y, 25" Z, 40 tap, gear hd., 20 ATC, 20 HP, 2006, #C5348 Show photo of item Show item detail
S & M Machinery Sales Inc, Warren, MI 586-755-1234 (Fax 586-755-9876) Spencer Minns
Haas #VF-3YT-50, 3-Axis, 40" X, 26" Y, 25" Z, 7500 RPM, Cat 50, 30 ATC, chip auger, 2008 Show photo of item
Machinery Network Inc, Encino, CA 310-826-4440 (Fax 818-788-2470) Sales Dept.
Haas #VF-4, 50" x 20" x 25" , 20 ATC, 4th Axis drive, WIP ready, 2013 Show photo of item
Machinery Management LLC, South Elgin, IL 847-608-9300 (Fax 847-608-9301) Tom Hazelhurst
Haas #VF-5, 23x52" , 50x26x25" , 5k RPM, CT50, 20 ATC, TSC, 4th ready, P cool, QC, aug, '99 Show photo of item Show Video of Item
520 Machinery Sales LLC, Schaumburg, IL 888-520-1768 (Fax 630-855-3535) Everett Dahlberg
Haas #VF-6/50, 3-Axis, 64" x32" x30" , 7500 RPM, Cat 50, 30 ATC side mount, chip auger, 2008 Show photo of item
Machinery Network Inc, Encino, CA 310-826-4440 (Fax 818-788-2470) Sales Dept.
Haas #VM-3, 40" X, 26" Y, 25" Z, 25" x54" table, 40 taper, ATC, 2007, #7022, #7023 (2)
Scott Machinery & Supply Inc, Helena, AL 205-664-9644 (Fax 205-664-9796) George Scott
Haas #VM-6, 60" X, 32" Y, 30" Z, 28" x64" table, 40 taper, ATC, 2007, #7025
Scott Machinery & Supply Inc, Helena, AL 205-664-9644 (Fax 205-664-9796) George Scott
Haas #VS-3, 150" X, 50" Y, 50" Z, 40" x146" table, 50 taper, ATC, 2004, #7026
Scott Machinery & Supply Inc, Helena, AL 205-664-9644 (Fax 205-664-9796) George Scott
Hurco #BMC-20, CNC vertical machining center Show photo of item Show item detail
Machinesused.com, Minneapolis, MN 763-745-1166 (Fax 651-315-8176) John Lawton
Hurco #BMC-20, Ultimax, 34" x16" , 24" x14" x16" , 6000 RPM, 10 HP, CT40, 1991 Show photo of item
520 Machinery Sales LLC, Schaumburg, IL 888-520-1768 (Fax 630-855-3535) Everett Dahlberg
Hurco #VM1-P, MAX CNC, 26" X, 14" Y, 18" Z, 12k RPM, BT30, 20 ATC, conv/G code, chiller, 2007 Show photo of item Show item detail
S & M Machinery Sales Inc, Warren, MI 586-755-1234 (Fax 586-755-9876) Spencer Minns
Hurco #VM1-P, MAX CNC, 26" X, 14" Y, 18" Z, 12k RPM, BT30, 20 side mount ATC, chiller, auger, '08 Show photo of item Show item detail
S & M Machinery Sales Inc, Warren, MI 586-755-1234 (Fax 586-755-9876) Spencer Minns
Hurco #VM1-P, MAX CNC, 26" X, 14" Y, 18" Z, 12k RPM, BT30, 20 ATC, conv/G code, chiller, 2008 Show photo of item Show item detail
S & M Machinery Sales Inc, Warren, MI 586-755-1234 (Fax 586-755-9876) Spencer Minns
Hwacheon Sirius #UL, Fanuc 18iMB, 40" X, 24" Y, 21.7" Z, 30 ATC, 12k RPM, '02, #153663 Show photo of item Show item detail
Machinery Values Inc, Harrison, NJ 973-497-7600 (Fax 973-497-7501) Jerry Donahue
Johnford #1600S, Fanuc 0i-MC, 63" X, 43" Y, 32" Z, 15 HP, 15k RPM, 2006 Show photo of item
Altman Machinery Co, Chicago, IL 773-247-4343 (Fax 773-247-2666) Howard /Steve
Johnford #DMC-1600H Hi-Net double column machining center Show photo of item Show item detail
Manufacturing Solutions, Costa Mesa, CA 714-545-0940 (Fax 310-943-3550) Mike Dieveney
Johnford #DMC-1600H-APC, F18iMB, 60ATC, auto pllt shuttle, 6k RPM, CTS, 63" x51" x31" , '08 Show photo of item Show item detail
Precision Machinery Sales Inc, Elk River, MN 763-370-7460 Matt Klein
Johnford #SV-32, 31.5x20x24.5, 10K, w/ZF-gbox, ct40, 24atc, CTS, F-0i-MD, low hrs, '10/'11 Show photo of item Show item detail
Amera-Seiki Corp., Hiawatha, IA 319-730-0326 (Fax 319-377-3035) Brad Pekerik
Kitamura Mycenter #3Xif, Fanuc 16i-MB, (2)16" x35" pallets, 30 ATC, 20k RPM, 2005
Lee Stevens Machinery Inc., Wixom, MI 248-926-8400 (Fax 248-926-8499) Randy/ Jeff/Chris
Kitamura Mycenter #3XiF Sparkchanger, Fanuc 16iMB, 20k RPM, CT40, 30 ATC, 30x18x18" , '05 Show photo of item Show item detail
Vander Ziel Machinery Sales, Alto, MI 616-868-1111 (Fax 616-868-1115) Steve Vander Ziel
Makino #S56, Pro 5, 35.4" X, 19.7" Y/Z, 13k RPM, HSK63, 20 ATC, 2007 (2) Show photo of item Show item detail
S & M Machinery Sales Inc, Warren, MI 586-755-1234 (Fax 586-755-9876) Spencer Minns
Makino #S56, Pro 5, 35.4" X, 19.7" Y/Z, 13k RPM, HSK63, CTS, 30 ATC, auger, 2007 (2) Show photo of item Show item detail
S & M Machinery Sales Inc, Warren, MI 586-755-1234 (Fax 586-755-9876) Spencer Minns
Matsuura #MAM72-63V, 5-Axis Trunnion, G-Tech, 29.9" x33.3" x24" , 360°C-axis, 90 ATC, 2005 Show photo of item
Machinery Network Inc, Encino, CA 310-826-4440 (Fax 818-788-2470) Sales Dept.
Matsuura #MC-1500V4, Fanuc 11M, 60.2" X, 30.7" Y, 29.5" Z, BT-45 taper, 40 ATC Show photo of item
Machinery Network Inc, Encino, CA 310-826-4440 (Fax 818-788-2470) Sales Dept.
Matsuura #VMC-760VX, Yasnac MX-3, 30" x17" x19" , 6k RPM, #40 tpr, 30 ATC, box ways, 1991 Show photo of item
520 Machinery Sales LLC, Schaumburg, IL 888-520-1768 (Fax 630-855-3535) Everett Dahlberg
Mazak #VCN-510C/2PC, 3-Axis, Mazatrol 640M Nexus, 41.3" x20" x20" , (2)51.2" x21.6" pllts, '06 Show photo of item
Machinery Network Inc, Encino, CA 310-826-4440 (Fax 818-788-2470) Sales Dept.
Mighty #BM-1100, Fanu 18iMB, 51x23" , 43x23x23" , 10k RPM, CT40, 24SM ATC, box ways, 2006 Show photo of item
520 Machinery Sales LLC, Schaumburg, IL 888-520-1768 (Fax 630-855-3535) Everett Dahlberg
Milltronics Partner #VM-24
Lee Stevens Machinery Inc., Wixom, MI 248-926-8400 (Fax 248-926-8499) Randy/ Jeff/Chris
Milltronics #VM25, 50" x25" x24" travels, rigid tap, CT40, ATC, 8000 RPM, 35 HP, 2007
Advanced Jones Machinery Co, Dayton, OH 937-278-7337 (Fax 937-278-8234) Bob Gibson
Mori-Seiki #MV-65 Show photo of item Show item detail
RAAR Group, Redondo Beach, CA 310-487-3800 (Fax 702-947-6320) Rick Schotts
Mori-Seiki #NT-1000/WZM, Y-Axis, mill turn, live lower turret, 2010, installed 2012 Show photo of item
Clark Machinery Sales LLC, Hunt Valley, MD 410-252-5494 (Fax 443-269-0660) Troy Clark
Morton #VTC-4080, CNC vertical mill Show photo of item Show Video of Item Show item detail
Miedema Auctioneering & Appraisals Inc, Byron Center, MI 616-538-0367 (Fax 616-538-5230) Amada Bowers
OKK #MCV1060, F16iM, 84" X, 41" Y, 31" Z, 6k RPM, 35 HP, 40 ATC, handwheel, coolant, 2001 Show photo of item Show item detail
S & M Machinery Sales Inc, Warren, MI 586-755-1234 (Fax 586-755-9876) Spencer Minns
Roders #RP600, high speed machining center Show photo of item Show Video of Item Show item detail
Miedema Auctioneering & Appraisals Inc, Byron Center, MI 616-538-0367 (Fax 616-538-5230) Amada Bowers
Sharp #SV-2414, Fanuc Oi Mate-MD, 24" x13.8" x18" , 10k RPM, 10 ATC, Cat 40, 2012 Show photo of item Show item detail
Precision Machinery Sales Inc, Elk River, MN 763-370-7460 Matt Klein
Sharp #SV-6030, 60" X, 30" Y, 27" Z, 10k RPM, Cat 40, 32 ATC, Fanuc Oi-MC, 2008 Show photo of item
Clark Machinery Sales LLC, Hunt Valley, MD 410-252-5494 (Fax 443-269-0660) Troy Clark
Supermax Max 1, CNC VMC, 3-Axis, Fanuc O-M, 26" X, 16" Y, 16" Z, #40 taper, 22 ATC, 7500 RPM, 1994, #M018533 Show photo of item Show Video of Item Show item detail
N & R Machine Sales, Navasota, TX 800-245-3194 (Fax 936-825-2679) Randy Nevels
Tree #Journeyman 330, Dynapath controls., 3-axis, 12.5" x48" T-slot table, 30" X, 11.7" Y, 5.75" Z, 17.5" vert.knee adj., 5 HP Show photo of item Show item detail
Hoff Online Auctions, Minneapolis, MN 612-521-5500 (Fax 612-331-3291) Denny Hoff
Tree #VMC-50, PC2100 control, 30" x20" x20" , 6000 RPM, 25 HP, CT40, 20 ATC, 1996 Show photo of item Show Video of Item
520 Machinery Sales LLC, Schaumburg, IL 888-520-1768 (Fax 630-855-3535) Everett Dahlberg
YCM #XV-1020A, 40" x 20' x 21" , 8k RPM, 24 ATC Show photo of item
Machinery Network Inc, Encino, CA 310-826-4440 (Fax 818-788-2470) Sales Dept.
41" x, 20" y, 20" z, mazak nexus 510c ii, 2007, cat 40, 30 atc, cts, 12, 000 rpm, 4th Show photo of item Show item detail
Prime Machinery Inc, Oyster Bay, NY 516-922-7977 (Fax 516-922-9691) Steve Brenner
60" x, 30" y, 25" z, doosan mv6030, cat 40, 8, 000 rpm, cts, 40 atc, chip conveyor Show photo of item Show item detail
Prime Machinery Inc, Oyster Bay, NY 516-922-7977 (Fax 516-922-9691) Steve Brenner
YCM-V168B, X-65" , Y-30" , CAT #50, Fanuc CNC, 32 ATC, 4th Axis Tbl, New 2007, #24983 Show photo of item Show item detail
Prestige Equipment Corp, Melville, NY 631-249-5566 (Fax 631-249-9494) Paul Lashin
MILLERS, VERTICAL/UNIVERSAL, CNC
Bridgeport Explorer 1, 3 axis, DX-32, 12" X36" table, 25" X12" X5" travel, cool, pwr draw, 3HP, 4200RPM, 97, manuals Show photo of item
Spier Machinery Corp, North Tonawanda, NY 716-694-4711 (Fax 716-694-0627) Paul Shear
Milltronics #VKM03, Series A, 3-Axis CNC, 12" x 50" , Milltronics Centurio 6, 3HP, (2001 Show photo of item Show item detail
Destiny Machinery Inc, Odessa, FL 727-376-2399 (Fax 727-372-8202) Dennis Laliberte
Sharp #TMV, CNC vertical miller, 10" x 50" , DRO, auto lubrication system, #A3685
Sterling Machinery Exchange, South El Monte, CA 626-444-0311 (Fax 626-443-9588) Adam Mattes
SWI Trak #DPM, 3-Axis, Proto Trak MX2 control, 3 HP, 4200 RPM, 10" x 50" tbl, 1997 Show photo of item Show item detail
Wheeler Machinery Sales, Pomona, CA 888-589-6721 (Fax 909-348-5617) Dan Wheeler
Tree Journeyman #310, CNC vertical miller, 10" x 44" , auto lube sys, coolant sys, #A2699
Sterling Machinery Exchange, South El Monte, CA 626-444-0311 (Fax 626-443-9588) Adam Mattes
Trak DPM, 10" x50" Tbl, 31" X, 17" Y, #40, 3Hp, AGE-3 control, Power Draw Bar, 2000. Show photo of item Show item detail
A Green Co Inc, Worcester, MA 508-791-6800 (Fax 508-791-6838) Harvey Green
PLASMA CUTTING SYSTEMS (FLAME CUTTERS), CNC
Messer CNC M2B2-0010, Pilot Control, 6' x 20' Dry Table, 1999, #6974
Scott Machinery & Supply Inc, Helena, AL 205-664-9644 (Fax 205-664-9796) George Scott
Retro Systems Hornet SS, 200 Amp, 5' x10', Hypertherm Micro Edge CNC Control, Dust Collector, 2005, #15922 Show photo of item Show item detail
Active Machinery Sales, Apex, NC 800-377-7553 (Fax 919-387-0096) Mike Sawaia
PUNCHES, SINGLE END, CNC
40 Ton Whitney 3400 RTC, X-140" , Y-60" , Fanuc 16P, 9 Sta. ATC, Hypertherm HT 2000, '99, #24977 Show photo of item Show item detail
Prestige Equipment Corp, Melville, NY 631-249-5566 (Fax 631-249-9494) Frank DiSalvo
PUNCHES, TURRET, CNC
22 Ton, Amada #AC255-NT, 4' x8', 58 sta.thk turret, 2 A/I, AC Servo elec.ram, '07, #15916 Show photo of item Show item detail
Active Machinery Sales, Apex, NC 800-377-7553 (Fax 919-387-0096) Mike Sawaia
22 Ton, Trumpf TruMatic #6000, 60" x 120" , 3200 watt, Siemens, Sheetmaster, 2010, #24950 Show photo of item Show Video of Item Show item detail
Prestige Equipment Corp, Melville, NY 631-249-5566 (Fax 631-249-9494) Frank DiSalvo
25 Ton, Trumpf #TC5000R, 4' x8', 18 rail mtd sta, Sheet Master ld/unld sys, '03, #15914 Show photo of item Show item detail
Active Machinery Sales, Apex, NC 800-377-7553 (Fax 919-387-0096) Mike Sawaia
25 Ton, Trumpf #TC500R-1600, 5' x10', 18 rail mtd sta, 3 material clamps, 1996, #15892 Show photo of item Show item detail
Active Machinery Sales, Apex, NC 800-377-7553 (Fax 919-387-0096) Mike Sawaia
33 Ton, Amada Pega #345 King, turret punch, 04PC CNC, 58 sta., 50" X72" , 1994, #11817
Blumberg Machinery Co, Bannockburn, IL 847-580-6800 (Fax 847-580-6801) Jerry/ Ryan
33 Ton, Amada Vipros #357 Queen, Fanuc 04PC & PHNC, 58 sta., 2 A/I, 1998, #10179 Show photo of item
Jordan Craig Machinery Intl L, New City, NY 845-398-0073 (Fax 845-398-0074) Jordan Craig
33 Ton, Amada Vipros #358 King, 4' x8', 58 sta., 4 1/2" A/I, hi-speed prog, '96, #15904 Show photo of item Show item detail
Active Machinery Sales, Apex, NC 800-377-7553 (Fax 919-387-0096) Mike Sawaia
33 Ton, Strippit #FC1000III, CNC turret punch, serial #317073087 Show photo of item
Plant Machinery & Equipment I, Excelsior, MN 952-933-1725 (Fax 952-933-1632) Jerry Brokaw
45 Ton, Wiedemann Magnum #5000, Fanuc OP, 52 sta., 2 A/I, 62" x74" trvl, tlng, '91, #24976 Show photo of item Show item detail
Prestige Equipment Corp, Melville, NY 631-249-5566 (Fax 631-249-9494) Frank DiSalvo
Amada Pega #357, Fanuc O4PC, hyd.clutch/brake, 58 stations, 1989, #7090
Fabricating Machinery Corp, Duarte, CA 626-359-0024 (Fax 626-359-4055) Scott Courneya
ROUTERS, CNC
Thermwood #C40, 2-spdls, 60" x60" vacuum tbl, 24k RPM, ATC, Thermwood CNC, '95/'02, #24929 Show photo of item Show item detail
Prestige Equipment Corp, Melville, NY 631-249-5566 (Fax 631-249-9494) Paul Lashin
SHEARS, POWER SQUARING & PLATE (INCHES), CNC
3/16" x 78.74" Amada #M-2045, CNC back gauge, s/n #20452088, 7.5 HP, #6807
Fabricating Machinery Corp, Duarte, CA 626-359-0024 (Fax 626-359-4055) Scott Courneya
1/4" x 10' Cincinnati #2500X10FSUIII, CNC Hyd, 48" FOPBG, 10' Pwr Squaring Arm, 32SPM, 25HP, 1996, #27395 Show photo of item Show item detail
Mohawk Machinery Inc, Cincinnati, OH 513-771-1952 (Fax 513-771-5120) Mr.Secord
1/4" x 12' Wysong #1225, CNC, PC100 pwr BG, mech, sq.arm, (2) front supports, #A3666 Show Video of Item
Sterling Machinery Exchange, South El Monte, CA 626-444-0311 (Fax 626-443-9588) Adam Mattes
COIL HANDLING EQUIPMENT
COIL CARS
10000 lb. Coe, 18" wide, 60" OD, traveling car / upender, 2010
Planet Machinery Co, Pontiac, MI 248-335-8330 (Fax 248-335-3680) Ken/ Chris
20000 lb. Littell, V-deck type, 18" lift, self-contained hydraulics
Libra Three Inc, Palmerton, PA 610-217-1868 Tom Kilcommons
FEED LINES
6000 LB FeedLease #R-6111-30, 30" Wx.065" TH, 6 Keepers, Rowe Servo Fd, & Strnr, 1988, #SR4751 Show photo of item Show item detail
Alma Machinery Co Inc, Columbia, TN 615-369-7788 (Fax 615-369-7789) Ken King
STRAIGHTENERS, SHEET & STRIP (Also See Levelers, Roller)
12" x .125" CWP #12tcs17, 17-roll straightener, entry & exit pinch rolls
Planet Machinery Co, Pontiac, MI 248-335-8330 (Fax 248-335-3680) Ken/ Chris
UNCOILERS, Including Reels, Centering
4000 lb. Littell #40-24, 24" wide, 60" OD, motorized, 1995
Planet Machinery Co, Pontiac, MI 248-335-8330 (Fax 248-335-3680) Ken/ Chris
10000 lb. ASL #1000, 48" wide, 60" OD, motorized, hydraulic expansion
Planet Machinery Co, Pontiac, MI 248-335-8330 (Fax 248-335-3680) Ken/ Chris
10000 lb. American Steel Line single uncoiler, 54" , #3139 Show photo of item Show item detail
Universal Tube & Rollform, Perrysburg, OH 419-872-2364 (Fax 419-874-2825) Sales Dept.
20000 lb. Iowa Precision #20M48DH, double uncoiler, 48"  Show photo of item Show item detail
Universal Tube & Rollform, Perrysburg, OH 419-872-2364 (Fax 419-874-2825) Sales Dept.
COMPARATORS, OPTICAL
14" MicroVu Century #2014, 2-Axis DRO, 22" x8" trvls, 10X, 20X, 50X, 3-lens turret, 1996 Show photo of item Show item detail
Adams Machinery Co, Lincolnwood, IL 847-673-0556 (Fax 847-673-7636) Sonneborn
SCHEER TUMICO 14" , Model 3500, DRO, 10" Travel, 10X Lense
Richlin Machinery Inc, Farmingdale, NY 631-694-9400 (Fax 631-694-9415) Irv Richlin
30" Jones & Lamson Epic #130, Optical Comparator with AcuRite Master MP DRO Show photo of item Show item detail
Machinesused.com, Minneapolis, MN 763-745-1166 (Fax 651-315-8176) John Lawton
30" Starrett #HF750, power table, joystick, 3 lenses, surface, QC2000 DRO
Advanced Jones Machinery Co, Dayton, OH 937-278-7337 (Fax 937-278-8234) Bob Gibson
CONVEYORS
BELT CONVEYORS
4-1/2" wide x 7.5' long, A Packaging Systems #TC-4500-AP Series, Stainless Steel belt conveyor Show photo of item Show Video of Item Show item detail
Frain Industries, Carol Stream, IL 630-629-9900 (Fax 630-629-6575) Dave Eggleston
CHAIN CONVEYORS
12" wide x 2.6' long, Plastic Delrin chain conveyor Show photo of item Show item detail
Frain Industries, Carol Stream, IL 630-629-9900 (Fax 630-629-6575) Dave Eggleston
14" wide x 14' long, Stainless Steel chain conveyor, 90°turn Show photo of item Show item detail
Frain Industries, Carol Stream, IL 630-629-9900 (Fax 630-629-6575) Dave Eggleston
24" wide x 7.8' long, Span Tech #ST, multi-span chain conveyor Show photo of item Show Video of Item Show item detail
Frain Industries, Carol Stream, IL 630-629-9900 (Fax 630-629-6575) Dave Eggleston
36" wide x 8' long, Von Gal 3 chain pallet conveyor (2) Show photo of item Show item detail
Frain Industries, Carol Stream, IL 630-629-9900 (Fax 630-629-6575) Dave Eggleston
48" wide x 8' long, Von Gal 3 chain pallet conveyor Show photo of item Show item detail
Frain Industries, Carol Stream, IL 630-629-9900 (Fax 630-629-6575) Dave Eggleston
Nercon, curved 90° Stainless Steel delrin chain conveyor Show photo of item Show item detail
Frain Industries, Carol Stream, IL 630-629-9900 (Fax 630-629-6575) Dave Eggleston
LANING CONVEYORS (LANERS)
8" wide, Dual lane Stainless Steel chain conveyor with 90°turn Show photo of item Show item detail
Frain Industries, Carol Stream, IL 630-629-9900 (Fax 630-629-6575) Dave Eggleston
ROLLER TYPE CONVEYORS
6" wide x 10' long, Shuttleworth Slip Torque roller conveyor Show photo of item Show Video of Item Show item detail
Frain Industries, Carol Stream, IL 630-629-9900 (Fax 630-629-6575) Dave Eggleston
SCREW TYPE CONVEYORS
10" diameter x 8' long, Stainless Steel tube style conveyor #10 Show photo of item Show item detail
Frain Industries, Carol Stream, IL 630-629-9900 (Fax 630-629-6575) Dave Eggleston
MISCELLANEOUS CONVEYORS
Varimot Stainless Steel transfer conveyor Show photo of item Show item detail
Frain Industries, Carol Stream, IL 630-629-9900 (Fax 630-629-6575) Dave Eggleston
COOLANT FILTERING SYSTEMS (Also See Filtration Systems)
Mosnic #RD3-112A, rot drum & drag flight conveyor, for Makino A-51/A-55/others, 2012 Show photo of item
Great American Eqpt Co, Cincinnati, OH 513-771-2111 (Fax 513-771-2552) Sales Dept.
Chipblaster JV8 1000 High Pressure Coolant System Show photo of item
American Systems & Equipment, Chicopee, MA 413-739-8170 (Fax 413-739-7964) Mark Barowsky
COOLING TOWERS, (Also See Chillers)
379 Ton, Evapco #AT-29-121, Cooling Tower, Stainless Steel bottom pan w/pump station, 2005, #48915 Show photo of item Show item detail
Federal Equipment Co, Cleveland, OH 216-271-3500 (Fax 216-271-5210) Joanne Parente
CRANES & EQUIPMENT
CRANES, JIB
Jib Cranes, assorted (9) Show photo of item
Machinery Network Inc, Encino, CA 310-826-4440 (Fax 818-788-2470) Sales Dept.
CRANES, OVERHEAD-BRIDGE
3 Ton, Crane America, 59'4" Span, bridge only, 460V, 120'(x2) steel available , 2011, #1527 Show photo of item Show item detail
Highland Machinery & Crane, Benton Harbor, MI 269-926-9600 (Fax 269-926-9601) C J Pawlowski
5 Ton, Detroit, 27'6" Span, 20' lift, pendant, VFD all, 1999, #1529 Show photo of item Show item detail
Highland Machinery & Crane, Benton Harbor, MI 269-926-9600 (Fax 269-926-9601) C J Pawlowski
5 Ton, Detroit, 36'7" Span, 20' lift, pendant, VFD all, 1999, #1528 Show photo of item Show item detail
Highland Machinery & Crane, Benton Harbor, MI 269-926-9600 (Fax 269-926-9601) C J Pawlowski
5 Ton, EMH, 50' Span, 20' lift, pendant, 2-Speed All, 460V, 1994, #1490 Show photo of item Show item detail
Highland Machinery & Crane, Benton Harbor, MI 269-926-9600 (Fax 269-926-9601) C J Pawlowski
5 Ton, P & H, 41'2" Span, 20' lift, 460V, pendant, #1502 Show photo of item Show item detail
Highland Machinery & Crane, Benton Harbor, MI 269-926-9600 (Fax 269-926-9601) C J Pawlowski
10 Ton, R & M, 27'6" Span, 20' lift, pendant, VFD bridge/trolley, 2002, #1530 Show photo of item Show item detail
Highland Machinery & Crane, Benton Harbor, MI 269-926-9600 (Fax 269-926-9601) C J Pawlowski
12 Ton, P & H TRDG, 50' Span, 15' lift, 480 VAC
Industrial Controls Corp, San Pierre, IN 219-689-2344 Rick Cannon
15 Ton, EMH, 43'8" Span, 30' lift, pendant, 1999, #1531 Show photo of item Show item detail
Highland Machinery & Crane, Benton Harbor, MI 269-926-9600 (Fax 269-926-9601) C J Pawlowski
15 Ton, EMH, 47' Span, 30' lift, pendant, 1999, #1532 Show photo of item Show item detail
Highland Machinery & Crane, Benton Harbor, MI 269-926-9600 (Fax 269-926-9601) C J Pawlowski
22/10 Ton, Whiting, 40'0" Span, 27' lift, radio, VFD aux & trolley, 2006, #1537 Show photo of item Show item detail
Highland Machinery & Crane, Benton Harbor, MI 269-926-9600 (Fax 269-926-9601) C J Pawlowski
33/15 Ton, Whiting TRDG, 94' Span, 35' lift, class E, 250 VDC, rebuilt
Industrial Controls Corp, San Pierre, IN 219-689-2344 Rick Cannon
50 Ton, Canadian Crane & Hoist, 67'-8" Span, 2012
Canadian Crane & Hoist Mfg Lt, Barrie, ON 705-726-5951 (Fax 705-726-2434) Nosratola Sabet
53/20 Ton, EMH, 118' Span, class D, 33' lift, radio, VFD all, low headroom, 2006, #1526 Show photo of item Show item detail
Highland Machinery & Crane, Benton Harbor, MI 269-926-9600 (Fax 269-926-9601) C J Pawlowski
6(3/3) Ton, Saturn, 37' Span, 20' lift, VFD Br/Trly, dual trly, 360'(x2) St, 1998, #1533 Show photo of item Show item detail
Highland Machinery & Crane, Benton Harbor, MI 269-926-9600 (Fax 269-926-9601) C J Pawlowski
6(3/3) Ton, Saturn, 37' Span, 20' lift, VFD Br/Trly, dual Trly, 360'(x2) St, 1998, #1534 Show photo of item Show item detail
Highland Machinery & Crane, Benton Harbor, MI 269-926-9600 (Fax 269-926-9601) C J Pawlowski
HOISTS, MONORAIL & TROLLEY, for Cranes
2 Ton, Coffing electric hoist, 230/460 V., 3 phase, 60 Hz Show photo of item
DMBS, Houston, TX 713-847-7775 (Fax 713-847-9994) Mark Nawrot
CUT OFF MACHINES (Also See Tube Machinery)
1/4" - 2-1/4" Modern #2LNC, CNC tube cut off lathe, 20' hopper, swg pos.stdy & eject, '00 Show photo of item Show item detail
Westbrook Engineering Co, Warren, MI 866-367-7297 (Fax 586-759-3106) Sales Dept.
CUT-TO-LENGTH LINES
72" x .187" Cut to length line w/Voss corrective leveler, 60000 lb., under power
American Steel Products Co, Toledo, OH 419-346-2846 (Fax 419-843-5288) Ford Cauffiel
DEGREASERS (Also See Washing Machines)
Ultronix EE15 Vapor Degreaser, Tank Size 30 3/4" L x 14" W x 40" D , Basket Size 23 1/2" L x 12" W x 3" D, 2002. Show photo of item Show item detail
Orca Machine Tools Inc., Albertville, MN 763-494-9825 (Fax 763-494-9827) Theron Horn
DIE HANDLING EQUIPMENT
40000 lb. Hansford #1021, 30" x64" lower platen, 28" open hght, 360$°rotation, pwr elev, '70 Show photo of item Show item detail
Adams Machinery Co, Lincolnwood, IL 847-673-0556 (Fax 847-673-7636) Sonneborn
DRILLING & TAPPING MACHINES, AUTOMATIC (Also See Tappers)
Leland-Gifford #2LMS, 26" swing, #3MT, 150-1800 RPM, (2) PF, 8 spindle, 1974, #2128 Show item detail
Turner Industries Inc, Grand Rapids, MI 616-949-5910 (Fax 616-949-3461) Jeff/Bill/David
Leland-Gifford drill, #3082 Show item detail
Turner Industries Inc, Grand Rapids, MI 616-949-5910 (Fax 616-949-3461) Jeff/Bill/David
Leland-Gifford drill, 8 spindle, 11" btwn spindles, 29" nose to table, #3081 Show item detail
Turner Industries Inc, Grand Rapids, MI 616-949-5910 (Fax 616-949-3461) Jeff/Bill/David
Leland-Gifford drill, 8 spindle, #3080 Show photo of item Show item detail
Turner Industries Inc, Grand Rapids, MI 616-949-5910 (Fax 616-949-3461) Jeff/Bill/David
DRILLS, GEAR HEAD
Leland-Gifford drill, 8 spindle, #3080 Show photo of item Show item detail
Turner Industries Inc, Grand Rapids, MI 616-949-5910 (Fax 616-949-3461) Jeff/Bill/David
Leland-Gifford drill, 8 spindle, 11" btwn spindles, 29" nose to table, #3081 Show item detail
Turner Industries Inc, Grand Rapids, MI 616-949-5910 (Fax 616-949-3461) Jeff/Bill/David
Leland-Gifford drill, #3082 Show item detail
Turner Industries Inc, Grand Rapids, MI 616-949-5910 (Fax 616-949-3461) Jeff/Bill/David
DRILLS, HEAVY DUTY, MULTIPLE SPINDLE, VERTICAL
6 Spdl., Burgmaster Houdaille #1DL, turret drill press, 1/2" , drill chucks, stand, #A3711
Sterling Machinery Exchange, South El Monte, CA 626-444-0311 (Fax 626-443-9588) Adam Mattes
DRILLS, HEAVY DUTY, SINGLE SPINDLE, VERTICAL
20" Vectrax #401VZF, V/S, 75/1.5 HP, pwr dwnfd, #3MT, 1/2" drill chuck, mfg.in Taiwan, 2000 Show photo of item Show item detail
American Machinery Liquidators, East Brunswick, NJ 732-390-0006 (Fax 732-390-0559) Marc Gallanter
Delta #17-900, floor drill press, 16-1/2" x 5/8" , drill chuck, adjustable table, #A3709
Sterling Machinery Exchange, South El Monte, CA 626-444-0311 (Fax 626-443-9588) Adam Mattes
DRILLS, RADIAL (Also See Tappers)
3'-8" Summit, radial arm drill, 8" diameter column, #4 Morse taper spindle, 60-2k RPM, coolant, 3 HP, s/n #3847 Show photo of item Show item detail
Hoff Online Auctions, Minneapolis, MN 612-521-5500 (Fax 612-331-3291) Denny Hoff
3'-10" Speedmaster, #4MT, T-slot table & base, power elevation of table on column, s/n #1905, 5 HP, excellent, 1970s, #153452 Show photo of item Show item detail
Machinery Values Inc, Harrison, NJ 973-497-7570 (Fax 973-497-7501) David Valitt
4'-9" Carlton #1A, radial drill, 5 HP, 2000 RPM, #4MT, power elevation, manual clamping, 1980, #D570018 Show photo of item Show item detail
N & R Machine Sales, Navasota, TX 800-245-3194 (Fax 936-825-2679) Randy Nevels
5'-15" Cincinnati Bickford #4E, Super Service radial drill, 20 HP, 1750 RPM, #5 taper, power elevation & clamp, 1960, #D570056 Show photo of item Show item detail
N & R Machine Sales, Navasota, TX 800-245-3194 (Fax 936-825-2679) Randy Nevels
6'-19" Carlton #4A, radial drill, 30 HP, 1500 RPM, #6MT, power elevation & clamping, 1951, #D570057 Show photo of item Show item detail
N & R Machine Sales, Navasota, TX 800-245-3194 (Fax 936-825-2679) Randy Nevels
6'-19" Cincinnati Bickford #6E, radial drill, 15 HP, 1250 RPM, #6MT, power elevation & clamping, coolant, 1956, #D57009 Show photo of item Show item detail
N & R Machine Sales, Navasota, TX 800-245-3194 (Fax 936-825-2679) Randy Nevels
DUST COLLECTORS (Also See Blowers & Fans)
1350-5000 cfm Torit #UMA-450, C/S shaker bag dust, 10 HP, 230/460 V.blower, dual drum discharge, #48905 Show photo of item Show item detail
Federal Equipment Co, Cleveland, OH 216-271-3500 (Fax 216-271-5210) Joanne Parente
Air Quality Engineering Mistbuster #MB500, 1 phase, 60 cycle, 115 V.
Dynacom, Inc., Chagrin Falls, OH 440-543-1900 (Fax 440-543-9390) Tony Pfenning
S/S Dust Collector, 4' x 8', air lock, 36-bags, cages, 20 HP blower, on high legs, #70137 Show photo of item Show item detail
Federal Equipment Co, Cleveland, OH 216-271-3500 (Fax 216-271-5210) Joanne Parente
ELECTRICAL DISCHARGE MACHINES (EDM), RAM TYPE (SINKERS) (Also See CNC Section, EDMs)
Charmilles #Roboform 20, 25" x17" x9" tank, 15.75" x11.8" tbl, 4 pos tool, Erowa chuck, '95 Show photo of item
520 Machinery Sales LLC, Schaumburg, IL 888-520-1768 (Fax 630-855-3535) Everett Dahlberg
Charmilles #Roboform 4000, 47x31.5x16.5" tank, 31.5x22" tbl, 20 tool, C-Ax, Mag chuck, '92 Show photo of item
520 Machinery Sales LLC, Schaumburg, IL 888-520-1768 (Fax 630-855-3535) Everett Dahlberg
Ingersoll Gantry #2000, 126.8" x79.5" x49.2" tank, 66138 lbs.weight cap, beautiful, 2004 Show photo of item Show item detail
Concord Machinery, Pontiac, MI 248-335-0300 (Fax 248-335-0553) T.Hill/ Jason K.
FOOD PROCESSING EQUIPMENT (Also See Chemical,Petroleum,Gas & Processing Equipment)
DRYERS, FOOD
Hull #225FXS450-SS25C, Freeze Dryer, Stainless Steel, 13-usable chelves +1, 231 sq.ft.surf, SIP & CIP capable, jktd.50 psi, #48909 Show photo of item Show item detail
Federal Equipment Co, Cleveland, OH 216-271-3500 (Fax 216-271-5210) Joanne Parente
Virtis Genesis XL, 6.12 sq.ft. Stainless Steel freeze dryer, 4 usualbe shelves +1, shelves rated to -60° C, cond.to -70°C, 2003, #48910 Show photo of item Show item detail
Federal Equipment Co, Cleveland, OH 216-271-3500 (Fax 216-271-5210) Joanne Parente
FORGING MACHINERY & EQUIPMENT
RING ROLLERS, FORGING
Beche #RBQ-800A, round die cross rolling machines Show photo of item Show item detail
Hilco Industrial LLC, Farmington Hills, MI 248-419-1964 (Fax 248-254-9995) Ken Planet
Irle #B-10H, rim/ring former, serial #1297, adjustable support rolls, hydraulic power unit, electrical control system, #13108J Show photo of item
Timco Inc, Columbia, TN 931-381-1900 (Fax 931-381-5151) Kris Irvin
FORKLIFT TRUCKS (Also See Trucks, Industrial Service)
1780 lb. Namco #LC-20-20, LP powered stand-up forklift, 144" vertical lift, 36" tilting forks, solid tires, s/n #773164-L Show photo of item Show Video of Item Show item detail
Hoff Online Auctions, Minneapolis, MN 612-521-5500 (Fax 612-331-3291) Denny Hoff
5000 lb. White Mobilift #MY50, LP powered fork lift, 145" vertical lift, 48" tilting forks, high/low range, s/n #32200232 Show photo of item Show Video of Item Show item detail
Hoff Online Auctions, Minneapolis, MN 612-521-5500 (Fax 612-331-3291) Denny Hoff
30000 lb. Taylor Cushion Tire Diesel #T-300M, 9' Forks, cab enclosure, 2005, #27419 Show photo of item Show item detail
Mohawk Machinery Inc, Cincinnati, OH 513-771-1952 (Fax 513-771-5120) Mr.Secord
36000 lb. Taylor Cushion Tire Diesel #THD-360L, 9' Forks, cab enclosure, 2000, #27420 Show photo of item Show item detail
Mohawk Machinery Inc, Cincinnati, OH 513-771-1952 (Fax 513-771-5120) Mr.Secord
FOUNDRY EQUIPMENT
BLAST CLEANING/PEENING, FOUNDRY
Pangborn, 3 cu.ft., late model
Blast-Abrade Inc, Elyria, OH 440-353-0001 (Fax 440-353-0111) Tyler B.Cotton
TABLES, BLAST CLEANING, FOUNDRY
Pangborn #6LK Table Blast, 72" diameter table, 30 HP wheel, includes dust collector Show photo of item
Furnaces, Ovens & Baths, Inc, Clarkston, MI 248-625-7400 (Fax 248-625-4030) Jeffrey Hynes
FURNACES & OVENS
AMMONIA DISSOCIATORS
2000 cu.ft./hr., Drever, Elec. (3 Avail) Excellent Condition
W H Kay Co, The, Cleveland, OH 440-519-3800 (Fax 440-519-1455) Mike Kay
ATMOSPHERE GAS GENERATORS & ACCESSORIES
2000 cu.ft./hr., Drever Ammonia Dissociator, Elec. (3 Avail) Excellent Condition
W H Kay Co, The, Cleveland, OH 440-519-3800 (Fax 440-519-1455) Mike Kay
6000 cu.ft./hr., Sunbeam Exothermic (Rich), Gas
W H Kay Co, The, Cleveland, OH 440-519-3800 (Fax 440-519-1455) Mike Kay
8000 cu.ft./hr., Alhern Martin Exothermic, Gas
W H Kay Co, The, Cleveland, OH 440-519-3800 (Fax 440-519-1455) Mike Kay
BATCH TYPE FURNACES
18" W x 18" H x 36" D, Lindberg Elec. 2500$° F.
W H Kay Co, The, Cleveland, OH 440-519-3800 (Fax 440-519-1455) Mike Kay
24" W x 24" H x 60" D, Lindberg Elec. 1850$° F., Atmos w/ Fan
W H Kay Co, The, Cleveland, OH 440-519-3800 (Fax 440-519-1455) Mike Kay
28" W x 24" D x 18" H Grieve #NB-350, heat treat convection batch oven, 350°, timer, stand, racks, #A3715 Show photo of item
Sterling Machinery Exchange, South El Monte, CA 626-444-0311 (Fax 626-443-9588) Adam Mattes
36" W x 24" H x 48" D, Lindberg Elec. 2000$° F., Atmos
W H Kay Co, The, Cleveland, OH 440-519-3800 (Fax 440-519-1455) Mike Kay
BELT CONVEYOR FURNACES
Holcroft natural gas belt type draw furnace Show photo of item Show item detail
Hilco Industrial LLC, Farmington Hills, MI 248-419-1964 (Fax 248-254-9995) Ken Planet
BOX TYPE FURNACES
12" W x 7" H x 18" L Electra, 2100°F, with retort for nitrogen atmosphere Show photo of item
Furnace Brokers Inc, Tolland, CT 860-875-3712 (Fax 860-875-1393) Bouley/Sherman
36" x 24" x 24" Seco Warwick, electric, 1800 Deg F, 96" x 66" x 48" Table Load Dim, air operated lift door at front, #27409 Show photo of item Show item detail
Mohawk Machinery Inc, Cincinnati, OH 513-771-1952 (Fax 513-771-5120) Mr.Secord
48" x 48" x 72" Seco, electric, 1200 Deg F, air operated lifting door at front, 126" x 63" x 48" table load dimensions, #27406 Show photo of item Show item detail
Mohawk Machinery Inc, Cincinnati, OH 513-771-1952 (Fax 513-771-5120) Mr.Secord
48" x 48" x 72" Seco, electric, 1200 Deg F, air operated lifting door at front, 126" x 63" x 48" table load dimensions, #27408 Show photo of item Show item detail
Mohawk Machinery Inc, Cincinnati, OH 513-771-1952 (Fax 513-771-5120) Mr.Secord
CAR BOTTOM FURNACES
45" W x 60" H x 112" L Gas, 2000$° F., Fiber Lined, 2 Cars Show photo of item
W H Kay Co, The, Cleveland, OH 440-519-3800 (Fax 440-519-1455) Mike Kay
53" W x 48" H x 72" L Electric, 1400°F, PLC controls, fiber lined, 2 fans, Aerospace certified Show photo of item
Furnaces, Ovens & Baths, Inc, Clarkston, MI 248-625-7400 (Fax 248-625-4030) Jeffrey Hynes
96" W x 48" H x 360" L, Elec. 1400$°, Sauder " Auto-tilt" , 3 Fans Show photo of item
W H Kay Co, The, Cleveland, OH 440-519-3800 (Fax 440-519-1455) Mike Kay
DRAW FURNACES, BATCH TYPE
24" W x 24" H x 36" D, Trent, Elec. 1400$° F. Show photo of item
W H Kay Co, The, Cleveland, OH 440-519-3800 (Fax 440-519-1455) Mike Kay
42" W x 42" H x 72" L Despatch, 1350°F, electric Show photo of item
Furnace Brokers Inc, Tolland, CT 860-875-3712 (Fax 860-875-1393) Bouley/Sherman
96" W x 48" H x 30 Ft. L., Sauder Auto-Tilt Car Bottom, Elec. 1400$° F.
W H Kay Co, The, Cleveland, OH 440-519-3800 (Fax 440-519-1455) Mike Kay
DRAW FURNACES, CONTINUOUS TYPE
60" W x 12" H x 25 Ft. L, AFC Mesh Belt (Built in 2000), Gas 500$° F.
W H Kay Co, The, Cleveland, OH 440-519-3800 (Fax 440-519-1455) Mike Kay
DRUM FURNACES
Sahara #3E2CS, C/S electric drum oven, 59" W x 27" D x 48" H, bottom sump, dual door, top mtd.blower, 240 V., controls, #48774 Show photo of item Show item detail
Federal Equipment Co, Cleveland, OH 216-271-3500 (Fax 216-271-5210) Joanne Parente
HARDEN, QUENCH & TEMPERING FURNACES
24" W x 24" H x 36" D, Lindberg I/Q, Gas 1850$° F., Top Cool
W H Kay Co, The, Cleveland, OH 440-519-3800 (Fax 440-519-1455) Mike Kay
24" W x 36" D x 18" H Ipsen Straight-Thru IQ Furnace, 1850°F, gas-fired, #U-3620 Show photo of item Show item detail
Heat Treat Equipment Co, Canton, MI 734-331-3939 (Fax 734-331-3915) John Becker
30" W x 48" L x 24" H Dow/AFC IQ Furnace, 1850°F, gas-fired, #U-3606 Show photo of item Show item detail
Heat Treat Equipment Co, Canton, MI 734-331-3939 (Fax 734-331-3915) John Becker
30" W x 48" D x 30" H Surface Combustion IQ Furnace, 1750°F, gas-fired, #U-3619 Show photo of item Show item detail
Heat Treat Equipment Co, Canton, MI 734-331-3939 (Fax 734-331-3915) John Becker
30" W x 48" D x 30" H Surface Combustion batch/oil quench furnace, 1800°F, elec, #V-1068 Show photo of item Show item detail
Heat Treat Equipment Co, Canton, MI 734-331-3939 (Fax 734-331-3915) John Becker
36" W x 72" D x 36" H Surface Combustion Super IQ furnace, 1950°F, gas-fired, #V-1062 Show photo of item Show item detail
Heat Treat Equipment Co, Canton, MI 734-331-3939 (Fax 734-331-3915) John Becker
48" W x 48" D x 48" H Seco Warwick solution anneal batch/oil quench sys, 1200°F, #V-1066 Show photo of item Show item detail
Heat Treat Equipment Co, Canton, MI 734-331-3939 (Fax 734-331-3915) John Becker
Rogers Engineering, 4000 pph cast link belt, 1750°/1700°F, gas gired, complete line Show photo of item
Furnaces, Ovens & Baths, Inc, Clarkston, MI 248-625-7400 (Fax 248-625-4030) Jeffrey Hynes
HEAT TREATING FURNACES
39" W x 19.5" H x 20" L Schindler, 2000°, Eurotherm 2404 controls, 460 V., 3 ph, 45 amp Show photo of item Show item detail
Naab Sales Corporation, Hopkins, MN 952-933-6755 (Fax 952-933-7229) J.Van Heuveln
LABORATORY OVENS, CONVECTION
Hosokawa #PT-N, Powder Tester, Serial #996328, 1999, #48791 Show photo of item Show item detail
Federal Equipment Co, Cleveland, OH 216-271-3500 (Fax 216-271-5210) Joanne Parente
MESH BELT CONVEYOR FURNACES
60" W x 12" H x 25 Ft. L, AFC Mesh (Built 2000), Gas 500$° F.
W H Kay Co, The, Cleveland, OH 440-519-3800 (Fax 440-519-1455) Mike Kay
OVENS, CABINET TYPE
19" W x 18" H x 15" D Blue M #OV-490A-2, sgl.door, 38°/-260° C, 1600 watt heater, 120 V., single phase, #48781 (2) Show photo of item Show item detail
Federal Equipment Co, Cleveland, OH 216-271-3500 (Fax 216-271-5210) Joanne Parente
19" W x 18" H x 15" D Blue M #OV-500C-2, sgl.door, 38°/-260° C, 1600 watt heater, 240 V., single phase, #48786 (2) Show photo of item Show item detail
Federal Equipment Co, Cleveland, OH 216-271-3500 (Fax 216-271-5210) Joanne Parente
19" W x 18" H x 15" D Blue M #OV-580C-2, Stainless Steel mechanical convention oven, Analog timer, #A3608 Show photo of item
Sterling Machinery Exchange, South El Monte, CA 626-444-0311 (Fax 626-443-9588) Adam Mattes
25" W x 20" H x 20" D Blue M, electric, 650°F, Stainless Steel interior, programmable controller Show photo of item
S & S Furnace Sales Inc, Enfield, CT 860-745-6116 (Fax 860-745-7117) Steve Davis
25" W x 20" H x 20" D Blue M, electric, 650°F, Stainless Steel interior, programmable controller Show photo of item
S & S Furnace Sales Inc, Enfield, CT 860-745-6116 (Fax 860-745-7117) Steve Davis
37" W x 37" H x 37" L Despatch, 550°F, electric Show photo of item
Furnace Brokers Inc, Tolland, CT 860-875-3712 (Fax 860-875-1393) Bouley/Sherman
38" W x 25" H x 20" L Blue M, nitrogen atmosphere, 1100°F Show photo of item
Furnace Brokers Inc, Tolland, CT 860-875-3712 (Fax 860-875-1393) Bouley/Sherman
38" W x 38" H x 26" L Grieve, 500°F, electric Show photo of item
Furnace Brokers Inc, Tolland, CT 860-875-3712 (Fax 860-875-1393) Bouley/Sherman
38" W x 42" H x 26" L Grieve #HB-1250, gas fired, 1200°F Show photo of item
Furnace Brokers Inc, Tolland, CT 860-875-3712 (Fax 860-875-1393) Bouley/Sherman
50" W x 54" H x 30" L Grieve #SA-550, 550°F, electric Show photo of item
Furnace Brokers Inc, Tolland, CT 860-875-3712 (Fax 860-875-1393) Bouley/Sherman
OVENS, CONTINUOUS TYPE
24" W x 24" H x 420" (35')L, Filco, 500°F, fas fired Show photo of item
Furnace Brokers Inc, Tolland, CT 860-875-3712 (Fax 860-875-1393) Bouley/Sherman
28" W x 2" H x 240" (20')L, ITS, 650°F, gas fired Show photo of item
Furnace Brokers Inc, Tolland, CT 860-875-3712 (Fax 860-875-1393) Bouley/Sherman
192" (16')W x 12" H x 108" L Heat-Pro, 550°F, gas fired Show photo of item
Furnace Brokers Inc, Tolland, CT 860-875-3712 (Fax 860-875-1393) Bouley/Sherman
OVENS, VACUUM
30" Diameter x 48" L, T-M Vacuum #H-3004, 400°C/752°F, PLC controls, (4) available Show photo of item
Furnaces, Ovens & Baths, Inc, Clarkston, MI 248-625-7400 (Fax 248-625-4030) Jeffrey Hynes
30" x 48" D T-M Vacuum, electric, 400°C, PLC controls. (4 available) Show photo of item
S & S Furnace Sales Inc, Enfield, CT 860-745-6116 (Fax 860-745-7117) Steve Davis
OVENS, WALK-IN TYPE
54" W x 64" H x 96" D, Prec.Quincy, Gas 650$° F.
W H Kay Co, The, Cleveland, OH 440-519-3800 (Fax 440-519-1455) Mike Kay
60" W x 72" H x 120" L, Wisc. Oven, Gas 500$° F. Show photo of item
W H Kay Co, The, Cleveland, OH 440-519-3800 (Fax 440-519-1455) Mike Kay
60" W x 84" H x 96" D, Callahan, Gas 500$° F. Show photo of item
W H Kay Co, The, Cleveland, OH 440-519-3800 (Fax 440-519-1455) Mike Kay
60" W x 96" H x 72" L Lanly, 450°F, electric
Furnace Brokers Inc, Tolland, CT 860-875-3712 (Fax 860-875-1393) Bouley/Sherman
72" W x 72" H x 72" D Gruenburg #KT45C272, electric walk-in oven, 450°, chart recorder Show photo of item
Machinery Network Inc, Encino, CA 310-826-4440 (Fax 818-788-2470) Sales Dept.
72" W x 72" H x 33' L Wisconsin Oven batch/temper furnace, 800°F, gas-fired, #V-1059 Show photo of item Show item detail
Heat Treat Equipment Co, Canton, MI 734-331-3939 (Fax 734-331-3915) John Becker
ROLLER HEARTH FURNACES
36" W x 72" L x 30" H, Park Thermal batch temper roller hearth, 1250°F, gas-fired, #C-0025 Show photo of item Show item detail
Heat Treat Equipment Co, Canton, MI 734-331-3939 (Fax 734-331-3915) John Becker
TEMPERING FURNACES
50" W x 50" H x 72" D, Grieve, Gas 1000$° F. Show photo of item
W H Kay Co, The, Cleveland, OH 440-519-3800 (Fax 440-519-1455) Mike Kay
30" W x 30" D x 48" H, Lindberg (N2), Elec. 1400$° F. Show photo of item
W H Kay Co, The, Cleveland, OH 440-519-3800 (Fax 440-519-1455) Mike Kay
30" W x 30" D x 30" H, Hevi-Duty, Elec. 1500$° F.
W H Kay Co, The, Cleveland, OH 440-519-3800 (Fax 440-519-1455) Mike Kay
24" W x 24" H x 36" D, Trent, Elec. 1400$° F. Show photo of item
W H Kay Co, The, Cleveland, OH 440-519-3800 (Fax 440-519-1455) Mike Kay
24" W x 24" H x 36" D Seco Warwick hi-temp box furnace, 1800°F, electric, #V-1067 Show photo of item Show item detail
Heat Treat Equipment Co, Canton, MI 734-331-3939 (Fax 734-331-3915) John Becker
48" W x 48" H x 72" D Seco Warwick batch/box temper furnace, 1250°F, electric, #V-1064 Show photo of item Show item detail
Heat Treat Equipment Co, Canton, MI 734-331-3939 (Fax 734-331-3915) John Becker
75" W x 60" H X 120" D Seco Warwick batch/box temper furnace, 1250°F, electric, #V-1065 Show photo of item Show item detail
Heat Treat Equipment Co, Canton, MI 734-331-3939 (Fax 734-331-3915) John Becker
TUBE FURNACES
Thermo Line #21100, Tube Furnace, 2" diameter x 12" L furnace section to 1200° C temp.range, 120 V., #48790 Show photo of item Show item detail
Federal Equipment Co, Cleveland, OH 216-271-3500 (Fax 216-271-5210) Joanne Parente
VACUUM FURNACES
24" W x 36" D x 24" H, Pacific Scientific vacuum temper furnace, 1450°F, electric, #C-0027 Show photo of item Show item detail
Heat Treat Equipment Co, Canton, MI 734-331-3939 (Fax 734-331-3915) John Becker
48" W x 60" D x 48" H, GM Enterprises vacuum furnace, 2500°F, electric, #V-1058 Show photo of item Show item detail
Heat Treat Equipment Co, Canton, MI 734-331-3939 (Fax 734-331-3915) John Becker
MISCELLANEOUS FURNACES, OVENS & PARTS
24" W x 12" H x 36" D, Washer, Ipsen " Dunk" , Elec. 200$° F.
W H Kay Co, The, Cleveland, OH 440-519-3800 (Fax 440-519-1455) Mike Kay
24" W x 24" H x 36" D, Lindberg Spray Washer, Gas 200$° F.
W H Kay Co, The, Cleveland, OH 440-519-3800 (Fax 440-519-1455) Mike Kay
36" W x 36" H x 48" D, Ipsen Washer, Dunk & Spray, Elec. 200$° F.
W H Kay Co, The, Cleveland, OH 440-519-3800 (Fax 440-519-1455) Mike Kay
AFC Charge Car ('99), Double Ended, 36" W x 48" Tray
W H Kay Co, The, Cleveland, OH 440-519-3800 (Fax 440-519-1455) Mike Kay
Heat Exchanger, #U-3539 Show photo of item
Heat Treat Equipment Co, Canton, MI 734-331-3939 (Fax 734-331-3915) John Becker
Heat Exchanger, Shell & Tube, Bell & Gossett, Oil / Water (2 Avail)
W H Kay Co, The, Cleveland, OH 440-519-3800 (Fax 440-519-1455) Mike Kay
Roller conveyor, 48" W x 20' L, #U-3565 Show photo of item Show item detail
Heat Treat Equipment Co, Canton, MI 734-331-3939 (Fax 734-331-3915) John Becker
GEAR GENERATORS, For Bevel,Helical,Herringbone,Hypoid & Spiral Gears
Gleason 12" , 18" pitch diameter , pwr chuck, dividing gauge, full set of gears w/cabinet Show item detail
Adams Machinery Co, Lincolnwood, IL 847-673-0556 (Fax 847-673-7636) Sonneborn
GEAR HOBBING MACHINERY (Hobbers), For Bevel, Helical, Spur & Worm Gears
Pfauter #P3000B Vertical, univ ho head w/auto hob shift, change gears, 120" max workpiece diam, 20 HP, #27436 Show photo of item Show item detail
Mohawk Machinery Inc, Cincinnati, OH 513-771-1952 (Fax 513-771-5120) Mr.Secord
GRINDERS, CENTERLESS
No. TG-12 Royal Master, 1.5" diameter , 12" grind wheel, 6" reg.wheel, rebuilt 1996, #24488 Show photo of item Show item detail
Prestige Equipment Corp, Melville, NY 631-249-5566 (Fax 631-249-9494) Paul Lashin
GRINDERS, CRANKSHAFT
Storm Vulcan #RG-200, crankshaft grinder Show photo of item Show item detail
Netmachinery Inc., Mooresville, NC 704-660-8130 (Fax 704-663-3475) David Kragh
GRINDERS, CYLINDRICAL, PLAIN (Also See Grinders, Roll)
5" x 12" Myford Model MG12-HM, Rapid Advance, Pickfeed, Internal, Collet Closer, 1994, Exc! Show photo of item Show Video of Item Show item detail
Roberts Machinery Sales, Ferndale, MI 248-543-4466 Kimball R Roberts
18" x 72" Norton #LC-2, OD grinder, heavy duty, No. 16 Jarno taper, 20 HP, '57, #153691 Show photo of item Show item detail
Machinery Values Inc, Harrison, NJ 973-497-7600 (Fax 973-497-7501) Andrew Valitt
GRINDERS, CYLINDRICAL, PLAIN, ANGLE HEAD (Also See Grinders, Angle Head)
Tschudin #HTG-442, angle head cylindrical grinder, rebuilt, excellent condition, 1977 Show photo of item Show item detail
Rohner Machinery Sales Inc, Fullerton, CA 888-440-4460 (Fax 714-441-1557) Chris Rohner
GRINDERS, CYLINDRICAL, UNIVERSAL
12" x 36" Okamoto #OGM-1236U, Okamoto Fanuc MDI Teach-In control, 14" wheel, 2007 Show photo of item
Machinery Network Inc, Encino, CA 310-826-4440 (Fax 818-788-2470) Sales Dept.
14" x 60" Mighty #M013300, ID/OD grinder, auto.feed, hyd.tbl., 1999, #152716 Show photo of item Show item detail
Machinery Values Inc, Harrison, NJ 973-497-7600 (Fax 973-497-7501) Andrew Valitt
GRINDERS, DRILL
Oliver #600, drill grinder, auto.infeed, 3" diameter , scroll chuck, coolant tank & pump, s/n #G8400, reconditioned 2015, #151342 Show photo of item Show item detail
Machinery Values Inc, Harrison, NJ 973-497-7600 (Fax 973-497-7501) Andrew Valitt
GRINDERS, INTERNAL (Also See CNC & Machinery & Equipment - Grinders, Internal)
Heald #273A, universal OD/ID grinder, 220/440 V., 3 phase ext table, 4' riser, #12992 Show photo of item Show Video of Item
Expert Machine Repair & Sales, Fraser, MI 586-296-2250 (Fax 586-296-9620) Jeff Novak
Heald #273A, universal OD/ID grinder, 220/440 V., 3 phase, #12991 Show photo of item Show Video of Item
Expert Machine Repair & Sales, Fraser, MI 586-296-2250 (Fax 586-296-9620) Jeff Novak
GRINDERS, STRUT
32" /120" x 120" /180" Norton gap bed cylindrical, 36" 4-Jaw chuck Show photo of item
Asset Exchange Corporation, Chicago, IL 773-866-9600 (Fax 773-866-9601) Scott / Mark
GRINDERS, SURFACE RECIPROCATING TABLE (Horizontal Spindle)
6" x 12" Boyar-Schultz #H612, surface grinder, 6" x 12" Permanent Mag.chuck, #A2179 Show photo of item
Sterling Machinery Exchange, South El Monte, CA 626-444-0311 (Fax 626-443-9588) Adam Mattes
6" x 18" Brown & Sharpe #618 Micromaster, auto hyd., USA made iron, EMC, excellent, 1966 Show photo of item Show item detail
Rohner Machinery Sales Inc, Fullerton, CA 888-440-4460 (Fax 714-441-1557) Chris Rohner
6" x 18" Chevalier Super #618, auto hydraulic, 6" x18" tbl & Mag.chuck, 2 HP, parallel Show photo of item Show item detail
Orca Machine Tools Inc., Albertville, MN 763-494-9825 (Fax 763-494-9827) Theron Horn
6" X 18" Chevalier FSG-618, mag. chuck, coolant, work light, manual Show photo of item
Spier Machinery Corp, North Tonawanda, NY 716-694-4711 (Fax 716-694-0627) Paul Shear
6" x 18" Harig #618W, hand, 2-Axis Mitutoyo DRO, 6" x18" Walker Ceramax manual chuck Show photo of item Show Video of Item Show item detail
Naab Sales Corporation, Hopkins, MN 952-933-6755 (Fax 952-933-7229) J.Van Heuveln
6" x 18" K.O. Lee #S718HG, 20" long., 7-1/8" cross, 6-1/4" x18-1/8" electromagnetic chuck w/controls, coolant, s/n #15375DD Show photo of item Show Video of Item Show item detail
Hoff Online Auctions, Minneapolis, MN 612-521-5500 (Fax 612-331-3291) Denny Hoff
6" x 18" K.O. Lee #SE618, manual surface grinder Show photo of item
Netmachinery Inc., Mooresville, NC 704-660-8130 (Fax 704-663-3475) David Kragh
6" x 18" Parker-Majestic #2Z, Sony 2-axis DRO, power elevation, Volkmann elect.spindledrive, s/n #5978ZV-95, 1995, #152303 Show photo of item Show item detail
Machinery Values Inc, Harrison, NJ 973-497-7600 (Fax 973-497-7501) Andrew Valitt
6" x 18" Parker Majestic surface grinder, #9025 Show photo of item Show item detail
Vander Ziel Machinery Sales, Alto, MI 616-868-1111 (Fax 616-868-1115) Steve Vander Ziel
8" x 18" Chevalier #FSG-2A818, automatic surface grinder, 2 HP, 8" x.50" grinding wheel, coolant, over the wheel dresser, #G802536 Show photo of item Show item detail
N & R Machine Sales, Navasota, TX 800-245-3194 (Fax 936-825-2679) Randy Nevels
8" x 20" Okamoto #ACC820DX, 3-Axis, 2 HP, rough, finish, sparkout, 3600 RPM, 1996 Show photo of item Show item detail
Adams Machinery Co, Lincolnwood, IL 847-673-0556 (Fax 847-673-7636) Sonneborn
12" x 24" Gallmeyer & Livingston #370, surface grinder, #11068 Show photo of item Show item detail
Vander Ziel Machinery Sales, Alto, MI 616-868-1111 (Fax 616-868-1115) Steve Vander Ziel
12" x 24" Okamoto #Accugar 124, 3-Axis Automatic, Kanetsu Electromagnetic Chuck, (1975) Show photo of item Show item detail
Destiny Machinery Inc, Odessa, FL 727-376-2399 (Fax 727-372-8202) Dennis Laliberte
12" x 58" Grand Rapids #A, surface grinder, 15 HP, 12" x43" mag.chuck, incremental downfeed, 1975, #G802523 Show photo of item Show item detail
N & R Machine Sales, Navasota, TX 800-245-3194 (Fax 936-825-2679) Randy Nevels
20" x 40" Kent #KGS-510AHD, hydraulic surface grinder, #10936 Show photo of item Show item detail
Vander Ziel Machinery Sales, Alto, MI 616-868-1111 (Fax 616-868-1115) Steve Vander Ziel
GRINDERS, SURFACE, ROTARY TABLE, HORIZONTAL SPINDLE
Blanchard #26HD48, 56" swing, 48" chuck, 24" under wheel, geared hd., 100 HP, 1975 Show photo of item
Bayshore Industrial Sales Inc, Grosse Pointe, MI 313-881-2120 (Fax 313-881-4855) Eric Hoffman
Blanchard #54HD100, 160" sw., 120" chuck, 60" under whl., 72" wheel diameter , 250 HP, 1983 Show photo of item
Bayshore Industrial Sales Inc, Grosse Pointe, MI 313-881-2120 (Fax 313-881-4855) Eric Hoffman
Mattison #36-144, 36" x72" mag.chuck, 168" table trvl., 2-Axis Acu-Rite RO, 50 HP, '61 Show photo of item
Bayshore Industrial Sales Inc, Grosse Pointe, MI 313-881-2120 (Fax 313-881-4855) Eric Hoffman
Mattison #96-54, 120" swing, 108" chuck, 54" wheel, coolant & pump, 300 HP, 1971 Show photo of item
Bayshore Industrial Sales Inc, Grosse Pointe, MI 313-881-2120 (Fax 313-881-4855) Eric Hoffman
GRINDERS, SURFACE, ROTARY TABLE, VERTICAL SPINDLE
Blanchard #11-20, 20" chuck, dry base w/coolant, 15 HP, s/n #13931, 1973, #153701 Show photo of item Show item detail
Machinery Values Inc, Harrison, NJ 973-497-7600 (Fax 973-497-7501) Andrew Valitt
Blanchard #54-100, 100" mag.chuck, 54" seg.whl, hyd.tbl traverse, dresser, lube, '72, #M9493 Show photo of item
Universal Press & Machy Inc, Clinton Township, MI 586-569-0150 (Fax 586-569-0103) Sales Dept.
Elgin #36, 30" Chuck, 36" Swing, 11.75" Vertical , Coolant Filter, 1988 S33656 Show item detail
Perfection Machinery Sales, Elk Grove Village, IL 847-427-3333 (Fax 847-427-8884) Sales Dept.
Mattison #96, 120" mag.chuck, 60" seg.wheel, 300 HP, hyd.vert.column, 1988, #M9494 Show photo of item
Universal Press & Machy Inc, Clinton Township, MI 586-569-0150 (Fax 586-569-0103) Sales Dept.
GRINDERS, TOOL & CUTTER (Also See Grinders Tool & Cutter, CNC)
No. NK-8 Nakabo (Monoset Style), tool & cutter grinder, portable on casters Show photo of item Show item detail
Machinesused.com, Minneapolis, MN 763-745-1166 (Fax 651-315-8176) John Lawton
No. M-40 Supermax (Taiwanese copy #2 Cincinnati), 10" x27" tbl., tilt/swivel whlhd, '95
Grand Marshall Machinery Inc, Hauppauge, NY 631-777-3600 (Fax 631-777-3603) Larry/ Paul/Marshall
HEATERS, DIRECT FIRED, GAS, OIL, VAPORIZERS, ETC.
18 KW, Mokon #42A18.S2, Hot Oil Heater, single zone, 230 V. w/controls, Ser. #62603, #48778 Show photo of item Show item detail
Federal Equipment Co, Cleveland, OH 216-271-3500 (Fax 216-271-5210) Joanne Parente
HONES VERTICAL (Also See Superfinishers)
Sunnen #CV-616E, 3/4" -8" boring dia, 2 HP, 1750 RPM, 150 ci sludge capacity, 1990 Show photo of item
520 Machinery Sales LLC, Schaumburg, IL 888-520-1768 (Fax 630-855-3535) Everett Dahlberg
Sunnen #DMS3-30 Bore-Sizer 3 Spindle Single Column, (3) Sunnen precision Spdls, .233" to 2.055" internal diam, 5HP, #27384 Show photo of item Show item detail
Mohawk Machinery Inc, Cincinnati, OH 513-771-1952 (Fax 513-771-5120) Mr.Secord
Engis #9425 four spindle vertical bore finishing system, #9425, 34" 8-station indexing table, (4) prec spdls, 5 HP, #27386 Show photo of item Show item detail
Mohawk Machinery Inc, Cincinnati, OH 513-771-1952 (Fax 513-771-5120) Mr.Secord
INDEXING MACHINES (INDEXERS) (Also See Assembly Machines)
Haas #HRT210, 8.3" platter, 210 ft-lbs torque, brush, red, 17 pin connection Show photo of item
520 Machinery Sales LLC, Schaumburg, IL 888-520-1768 (Fax 630-855-3535) Everett Dahlberg
Haas #HRT450, 17.7" platter, 400 ft-lbs torque, brushless, Sigma 5 motors, 2012 Show photo of item
520 Machinery Sales LLC, Schaumburg, IL 888-520-1768 (Fax 630-855-3535) Everett Dahlberg
Haas #TR-160, 6.3" platter, brushless, Sigma 5 motors, 2012 Show photo of item
520 Machinery Sales LLC, Schaumburg, IL 888-520-1768 (Fax 630-855-3535) Everett Dahlberg
IRONWORKERS
4" x 4" x 1/4" Hill-Acme Kling #3, 33 ton hydraulic ironworker Show photo of item Show item detail
Machinesused.com, Minneapolis, MN 763-745-1166 (Fax 651-315-8176) John Lawton
4" x 4" x 3/8" Geka #Minicrop, 50 ton, 12" blades, 6-7/8" throat, 4 HP, 1991, #9743 Show photo of item Show item detail
Turner Industries Inc, Grand Rapids, MI 616-949-5910 (Fax 616-949-3461) Jeff/Bill/David
6" x 6" x 5/8" Piranha #P-4, 90 ton ironworker, #11208 Show photo of item Show item detail
Vander Ziel Machinery Sales, Alto, MI 616-868-1111 (Fax 616-868-1115) Steve Vander Ziel
JIG MILLS (Also See CNC & N/C Machinery & Equipment - Jig Mills)
DeVlieg #3B-48 Spiramatic, jig mill, horizontal with 3-Axis DRO Show photo of item Show item detail
Machinesused.com, Minneapolis, MN 763-745-1166 (Fax 651-315-8176) John Lawton
KEYSEATERS
1/16" - 1-1/4" DC Morrison #K, keyseat machine, 9" max. length of cut, 1983 Show photo of item Show item detail
Charleston Annex Corporation, Indian Trail, NC 704-821-7370 (Fax 704-821-7392) Lance/ Mark
1-1/2" Davis #15B, 1/16" to 1-1/2" cap., 20" x31" table w/(3) T-slots, 4.5" cutter stroke, 45 SPM, s/n #15-804, 2 HP, 1981, #15003 Show photo of item Show item detail
Hildebrand Machinery Co Inc, York, PA 717-846-2600 (Fax 717-845-9497) Dave Hildebrand
LABORATORY & RESEARCH EQUIPMENT (Also See Testing Equipment)
Centrifuge, Beckman Coulter #J-20XPI, refrigerated, 10000 RPM, -10° to +40° range, 82000max G-force, 200/240 V., #48812 Show photo of item Show item detail
Federal Equipment Co, Cleveland, OH 216-271-3500 (Fax 216-271-5210) Joanne Parente
Centrifuge, Eppendorf #5804, for 200-14000 RPM, cap.(4) 250 ml vials, 900 w.115 V, 47cm W x 55cm D x 34cm H, #48811 Show photo of item Show item detail
Federal Equipment Co, Cleveland, OH 216-271-3500 (Fax 216-271-5210) Joanne Parente
Centrifuge Rotor, Beckman #JA-10, 10000 RPM, cap. (6) 500 ml vials, Ser.#3503, #48810 Show photo of item Show item detail
Federal Equipment Co, Cleveland, OH 216-271-3500 (Fax 216-271-5210) Joanne Parente
Centrifuge Rotor, Beckman #JA-14, 14000 RPM, cap. (6) 500 ml vials, Ser.#5858, #48809 Show photo of item Show item detail
Federal Equipment Co, Cleveland, OH 216-271-3500 (Fax 216-271-5210) Joanne Parente
Centrifuge Rotor, Beckman #JA-17, 17000 RPM, cap.(14) 50 ml vials, Ser.#992-3978, #48808 Show photo of item Show item detail
Federal Equipment Co, Cleveland, OH 216-271-3500 (Fax 216-271-5210) Joanne Parente
Centrifuge Rotor, Beckman #JA-20, 20000 RPM, cap.(8) 15 ml w/inserts(included) or (8) 50 ml vials, Ser.#8085, #48807 Show photo of item Show item detail
Federal Equipment Co, Cleveland, OH 216-271-3500 (Fax 216-271-5210) Joanne Parente
Fraction Collector, Amersham #FRAC-950, Serial #1093115, #48805 Show photo of item Show item detail
Federal Equipment Co, Cleveland, OH 216-271-3500 (Fax 216-271-5210) Joanne Parente
Fraction Collector, Amersham #FRAC-950, Serial #1092786, #48806 Show photo of item Show item detail
Federal Equipment Co, Cleveland, OH 216-271-3500 (Fax 216-271-5210) Joanne Parente
LATHES, ENGINE (Also See Lathes, Engine, Gap or Tracer & Copying)
13" x 30" Clausing Colchester #8015, geared head lathe, 8" 4-jaw chuck, KDK tool holder, splash guard, clnt sys, collet closer, #A3710 Show photo of item
Sterling Machinery Exchange, South El Monte, CA 626-444-0311 (Fax 626-443-9588) Adam Mattes
13" x 40" Kaida #C6232ZK, lathe, #8488 Show photo of item Show item detail
Vander Ziel Machinery Sales, Alto, MI 616-868-1111 (Fax 616-868-1115) Steve Vander Ziel
15" x 30" LeBlond Makino Regal Servo Shift lathe, #11248 Show photo of item Show item detail
Vander Ziel Machinery Sales, Alto, MI 616-868-1111 (Fax 616-868-1115) Steve Vander Ziel
15" x 54" LeBlond Makino Regal Servo Shift, engine lathe, in/mm, 3&4-jaw chucks, taper attachment, 1800 RPM, 1987, #L300042 Show photo of item Show item detail
N & R Machine Sales, Navasota, TX 800-245-3194 (Fax 936-825-2679) Randy Nevels
15" x 54" LeBlond Makino Regal Servo Shift, engine lathe, in/mm, 3&4-jaw chucks, taper attachment, 1800 RPM, 1984, #L300061 Show photo of item Show item detail
N & R Machine Sales, Navasota, TX 800-245-3194 (Fax 936-825-2679) Randy Nevels
15" x 54" LeBlond Makino Regal Servo Shift, engine lathe, in/mm, 3&4-jaw chucks, taper attachment, 1800 RPM, 1987, #L300046 Show photo of item Show item detail
N & R Machine Sales, Navasota, TX 800-245-3194 (Fax 936-825-2679) Randy Nevels
16" x 40" Tos-Trencin #SN40C, gap bed, inch/metric, 7.3 HP, coolant
Advanced Jones Machinery Co, Dayton, OH 937-278-7337 (Fax 937-278-8234) Bob Gibson
16" x 40" Victor / Fortune #1640G, 2" hole, 3-jaw, QC TP, in/mm, clnt, rear guard, runs nice
J Hebert Machine Tool Co., Charlotte, NC 704-825-1511 Jon Hebert
18" x 60" CLAUSING COLCHESTER " Mascot VS" , 15 HP, 3" bore, I/M 3J & 4J, FP, SR & FR, taper, DRO, 1995
J Hebert Machine Tool Co., Charlotte, NC 704-825-1511 Jon Hebert
20" x 174" American Pacemaker Style D, engine lathe, #4MT, 4-jaw 18" chuck, steady rest, 1973, #L30009 Show photo of item Show item detail
N & R Machine Sales, Navasota, TX 800-245-3194 (Fax 936-825-2679) Randy Nevels
21" x 120" Harrison, 1998
Belmont Machinery Co, Aurora, IL 630-844-9288 (Fax 630-844-9398) Sales
22" x 40" Cadillac #CL5685G, 12" 3-Jaw chuck, KDK live center, SR, FR, coolant system, 1999 Show photo of item Show item detail
ACT Inc, Fullerton, CA 714-441-1992 (Fax 714-441-1923) Randy Goodman
16" / 23" x 60" VICTOR 1660E, 2, 000 RPM, 3-JAW, STEADY REST Show photo of item Show item detail
Prime Machinery Inc, Oyster Bay, NY 516-922-7977 (Fax 516-922-9691) Steve Brenner
24" x 160" cc, LANSING-G, 35" SWING IN GAP, 14 1/2" OVER CS, 20 HP Show photo of item Show item detail
Prime Machinery Inc, Oyster Bay, NY 516-922-7977 (Fax 516-922-9691) Steve Brenner
24" /33" x 160" cc, LANSING-GS, UNUSED, 33" SWING IN GAP, 14 1/2" OVER CS, 25 HP Show photo of item Show item detail
Prime Machinery Inc, Oyster Bay, NY 516-922-7977 (Fax 516-922-9691) Steve Brenner
30" x 88" Clausing Colchester gap bed lathe, 6-3/4" spindle bore, #10931 Show photo of item Show item detail
Vander Ziel Machinery Sales, Alto, MI 616-868-1111 (Fax 616-868-1115) Steve Vander Ziel
36" x 132" Poreba #TPK90, 1987
Belmont Machinery Co, Aurora, IL 630-844-9288 (Fax 630-844-9398) Sales
36" x 20' Poreba #TPK90X6M, taper, 1979
Belmont Machinery Co, Aurora, IL 630-844-9288 (Fax 630-844-9398) Sales
39" x 27' Poreba #TRP100X8M, taper, 1977
Belmont Machinery Co, Aurora, IL 630-844-9288 (Fax 630-844-9398) Sales
42" x 102" Leblond #32" Standard, 50 HP, 5-625 RPM, 3" spindle bore, taper attachment Show photo of item Show item detail
Wheeler Machinery Sales, Pomona, CA 888-589-6721 (Fax 909-348-5617) Dan Wheeler
43" x 315" Poreba #TPK110, 31" OCS, taper attach, in/mm, steadies, 36 HP, rblt'14, #24966 Show photo of item Show item detail
Prestige Equipment Corp, Melville, NY 631-249-5566 (Fax 631-249-9494) Terry Lashin
52" x 315" Tacchi #FTC-71, 33" OCS, 2 steadies, threading, 60 HP
L S Walker Machine Tools Inc, Milton, ON 905-876-0890 (Fax 905-876-1959) Chris Walker
LATHES, ENGINE, GAP, Removable or Sliding Bed
Very Nice!! Dainichi 21$$$x54$$$ HD Gap Bed Engine Lathe, 2 Axis Digital Readout, Metric/English, 3 Jaw, Steady&Follow Rest, C** Show photo of item Show Video of Item Show item detail
Naab Sales Corporation, Hopkins, MN 952-933-6755 (Fax 952-933-7229) J.Van Heuveln
LATHES, ENGINE, OIL FIELD & HOLLOW SPINDLE
26" x 144" LeBlond Makino Regal Servo Shift #24, 3&4-jaw chucks, taper attachment, coolant, 1200 RPM, #L3000142 Show photo of item Show item detail
N & R Machine Sales, Navasota, TX 800-245-3194 (Fax 936-825-2679) Randy Nevels
30" x 120" Kingston #HK3000, 12-19/32" spdl bore, dbl chuck, tpr attach, in/mm, 300 RPM, '80 Show photo of item Show item detail
Wheeler Machinery Sales, Pomona, CA 888-589-6721 (Fax 909-348-5617) Dan Wheeler
36" x 120" Demoor hollow spindle engine lathe, 6" spindle hole, #5MT, steady rest, taper attachment, thread dial, #L410624 Show photo of item Show item detail
N & R Machine Sales, Navasota, TX 800-245-3194 (Fax 936-825-2679) Randy Nevels
36" x 120" Masteel #ML36120, hollow spindle engine lathe, 14" spindle hole, steady rest, 4 way tool post, 2012, #L410625 Show photo of item Show item detail
N & R Machine Sales, Navasota, TX 800-245-3194 (Fax 936-825-2679) Randy Nevels
41" x 78" Geminis #GE-1000S, 20" spdl bore, dbl chuck, 2-Axis DRO, in/mm, 200 RPM, 1969 Show photo of item Show item detail
Wheeler Machinery Sales, Pomona, CA 888-589-6721 (Fax 909-348-5617) Dan Wheeler
55" x 10' SMT #CNC-OCL635 x 3000, Flat Bed CNC Oil Country Lathe, 25" spindle hole Show photo of item Show item detail
Esco Machine & Supply, Sugar Land, TX 281-277-3726 (Fax 281-277-2891) R.G. Escandon
LATHES, ENGINE, RIGHT ANGLE "T"
36" Monarch T-Lathe, serial #T38482, 36" chuck, 1953 Show photo of item
Affordable Machinery, Grand Rapids, MI 616-200-4308 (Fax 269-623-5076) David Dimond
LATHES, TURRET, SADDLE (Also See CNC Machinery & Equipment - Lathes, Turret)
No. 3A Warner & Swasey, M3500, square head, saddle type turret lathe, 23-1/2" sw.o/bed ways, 40" cc, 4-3/4" spdl.hole, 1956, #L630443 Show photo of item Show item detail
N & R Machine Sales, Navasota, TX 800-245-3194 (Fax 936-825-2679) Randy Nevels
No. 3A Warner & Swasey, M3500, square head, saddle type turret lathe, 23-1/2" sw.o/bed ways, 43" cc, 6-1/4" spdl.hole, 1973, #L630431 Show item detail
N & R Machine Sales, Navasota, TX 800-245-3194 (Fax 936-825-2679) Randy Nevels
No. 3A Warner & Swasey, M3500, square head, saddle type turret lathe, 23-1/2" sw.o/bed ways, 43" cc, 4-3/4" spdl.hole, 1941, #L630448 Show photo of item Show item detail
N & R Machine Sales, Navasota, TX 800-245-3194 (Fax 936-825-2679) Randy Nevels
No. 3A Warner & Swasey, M3500, square head, saddle type turret lathe, 23-1/2" sw.o/bed ways, 43" cc, 6-1/4" spdl.hole, 1968, #L630436 Show photo of item Show item detail
N & R Machine Sales, Navasota, TX 800-245-3194 (Fax 936-825-2679) Randy Nevels
No. 4A Warner & Swasey, M3550, square hd, saddle type turret lathe, 28-1/4" swing o/bed ways, 62" cc, 9-1/4" spdl.hole, 1981, #L630417 Show photo of item Show item detail
N & R Machine Sales, Navasota, TX 800-245-3194 (Fax 936-825-2679) Randy Nevels
No. 4A Warner & Swasey, M3550, square hd, saddle type turret lathe, 28-1/4" swing o/bed ways, 62" cc, 9-1/4" spdl.hole, 1965, #L630460 Show item detail
N & R Machine Sales, Navasota, TX 800-245-3194 (Fax 936-825-2679) Randy Nevels
No. 4A Warner & Swasey, M3580, square hd, saddle type turret lathe, 28-1/4" swing o/bed ways, 62" cc, 9-1/4" spdl.hole, 1960, #L630442 Show photo of item Show item detail
N & R Machine Sales, Navasota, TX 800-245-3194 (Fax 936-825-2679) Randy Nevels
No. 4A Warner & Swasey, M3580, square hd, saddle type turret lathe, 28-1/4" swing o/bed ways, 62" cc, 12-1/2" spdl.hole, 1967, #L630462 Show photo of item Show item detail
N & R Machine Sales, Navasota, TX 800-245-3194 (Fax 936-825-2679) Randy Nevels
No. 4A Warner & Swasey, M3580, square hd, saddle type turret lathe, 28-1/4" swing o/bed ways, 62" cc, 12-1/2" spdl.hole, 1976, #L63043 Show item detail
N & R Machine Sales, Navasota, TX 800-245-3194 (Fax 936-825-2679) Randy Nevels
No. 5L Gisholt, saddle type turret lathe, 40" swing o/ways, 97-1/2" cc, 280 RPM, A-20, 32" 3-jaw chuck, coolant, 1952, #L630432 Show photo of item Show item detail
N & R Machine Sales, Navasota, TX 800-245-3194 (Fax 936-825-2679) Randy Nevels
MATERIAL HANDLING EQUIPMENT (Also See Lifts & Storage Equipment)
Acrison #105-Z-N, Screw Feeder, Stainless, with Hopper, #70136 Show photo of item Show item detail
Federal Equipment Co, Cleveland, OH 216-271-3500 (Fax 216-271-5210) Joanne Parente
Acrison #105Z-N, Screw Feeder, Stainless, with Hopper, #70135 Show photo of item Show item detail
Federal Equipment Co, Cleveland, OH 216-271-3500 (Fax 216-271-5210) Joanne Parente
Acrison #105Z-N, Screw Feeder, Stainless, with Hopper, #70133 Show photo of item Show item detail
Federal Equipment Co, Cleveland, OH 216-271-3500 (Fax 216-271-5210) Joanne Parente
Acrison #105Z-N, Screw Feeder, Stainless, with Hopper, #70134 Show photo of item Show item detail
Federal Equipment Co, Cleveland, OH 216-271-3500 (Fax 216-271-5210) Joanne Parente
Cherry' s Ind'l. #SC-75, Paller invert, 75" H max. jaw-open, 42" min.jaw open, 50" x 50" tbl, 4400# cap, flr.mtd, 230/460 V., #48906 Show photo of item Show item detail
Federal Equipment Co, Cleveland, OH 216-271-3500 (Fax 216-271-5210) Joanne Parente
Magliner 36' mobile loading ramp, 20000 lbs. capacity, #10811 Show photo of item Show item detail
Vander Ziel Machinery Sales, Alto, MI 616-868-1111 (Fax 616-868-1115) Steve Vander Ziel
Merrick #25-06, Volumetric feeder, Stainless Steel, .75" diameter screw w/hopper, Ser. #22518, #48780 Show photo of item Show item detail
Federal Equipment Co, Cleveland, OH 216-271-3500 (Fax 216-271-5210) Joanne Parente
Myers ram press, 15 HP, 230/460 V., 1760 RPM, 387.19 amp, 2541C Frame Show photo of item
DMBS, Houston, TX 713-847-7775 (Fax 713-847-9994) Mark Nawrot
Posi Turner Plate Rotator #1-80-12LHD, #10892 Show photo of item Show item detail
Vander Ziel Machinery Sales, Alto, MI 616-868-1111 (Fax 616-868-1115) Steve Vander Ziel
MEASURING MACHINES (Including Coordinate Measuring Machines CMM's)
Brown & Sharpe Global #FX12-22-10 DCC, 48" x80" x40" , PC DMIS Cad, PH-10MQ probe, '06 Show photo of item
Machinery Network Inc, Encino, CA 310-826-4440 (Fax 818-788-2470) Sales Dept.
Zeiss #MC-850, 33" x71" x24" , 4630 lb.capacity, joystick, probe, Calypso software
Advanced Jones Machinery Co, Dayton, OH 937-278-7337 (Fax 937-278-8234) Bob Gibson
METAL DETECTORS
Lock Metal Check #30+, 3.75" W x 1.5" H appurature w/reject, on cart w/panel, 115 V., Ser. #16501/1, 2003, #48825 Show photo of item Show item detail
Federal Equipment Co, Cleveland, OH 216-271-3500 (Fax 216-271-5210) Joanne Parente
MILLERS, PLAIN, HORIZONTAL, Bed & Knee Type (Also See CNC Machinery,Millers)
Kearney & Trecker #310-S15, 15.5" x 68.5" table, 34" long, 12" cross trvl, 2000 RPM, 1970, #M268027 Show photo of item Show item detail
N & R Machine Sales, Navasota, TX 800-245-3194 (Fax 936-825-2679) Randy Nevels
WMW Heckert #FU 450X1800 APUG, 17" x 71" table, double swivel vertical head, pendant, coolant, wide knee, #M268028 Show photo of item Show item detail
N & R Machine Sales, Navasota, TX 800-245-3194 (Fax 936-825-2679) Randy Nevels
MILLERS, PLANER TYPE (Also See Planers, Double Housing)
Ingersoll Masterhead CNC, AAC, ATC, 540" X, 201" Y, 118" btwn columns, Fanuc 15M, '95, #24803 Show photo of item Show item detail
Prestige Equipment Corp, Melville, NY 631-249-5566 (Fax 631-249-9494) Terry Lashin
Ingersoll Masterhead CNC, AAC, ATC, 540" X, 201" Y, 118" btwn columns, Fanuc 15M, '95, #24802 Show photo of item Show item detail
Prestige Equipment Corp, Melville, NY 631-249-5566 (Fax 631-249-9494) Terry Lashin
SNK #DC-5ASM, CNC 5-face, 40 ATC, 246" X, 145" Y, 118" BC, 6k RPM, Fanuc 15M, 1998, #24923 Show photo of item Show item detail
Prestige Equipment Corp, Melville, NY 631-249-5566 (Fax 631-249-9494) Paul Lashin
MILLERS, VERTICAL, Bed & Knee Type, (Also See CNC Machinery & Equip., Millers)
Bridgeport Series I, 9" x42" tbl., step pulley hd., chrome ways, pwr.feed, 2-axis, DRO
Heart Of Wisconsin Mchy Co, Nekoosa, WI 715-886-4926 (Fax 715-886-3016) Fred Parker
Bridgeport Series I, 9" x42" table, 30" long., 12" cross, Acu-Rite DRO, R-8, chrome, s/n #12/BR236054, 2 HP, 1984, #153566 Show photo of item Show item detail
Machinery Values Inc, Harrison, NJ 973-497-7570 (Fax 973-497-7501) David Valitt
Bridgeport Series I, vertical miller, vari-speed, 9" x42" , Mitutoyo 2-Axis DRO, Bijur lubrication sys, collet holder, #A3652 Show photo of item Show Video of Item
Sterling Machinery Exchange, South El Monte, CA 626-444-0311 (Fax 626-443-9588) Adam Mattes
Heckert #APUG-F400E, combination horizontal-vertical mill, 15 HP, pendant control, coolant system, PDB, arbor & 2 supports, #9933 Show photo of item
Sterling Machinery Exchange, South El Monte, CA 626-444-0311 (Fax 626-443-9588) Adam Mattes
KBC #TUM-TVS, 9" x42" tbl, 2-Axis Mitutoyo Digital Readout, align power table, 1992, #6802
Presses for Industry, Detroit, MI 313-839-9300 (Fax 313-839-9600) C. Thornton
Kearney & Trecker #315TF-16, vertical mill, #11221 Show photo of item Show item detail
Vander Ziel Machinery Sales, Alto, MI 616-868-1111 (Fax 616-868-1115) Steve Vander Ziel
NIBBLERS
No. P-6 Pullmax, universal plate cutting & working machine, 1/4" cap., 42" throat, 2.5/3 HP, s/n #52930-48, nice, #28812 Show photo of item Show item detail
C.W. Wood Machinery Inc, Cincinnati, OH 800-745-6008 (Fax 513-542-4819) Sales Dept.
PACKAGING EQUIPMENT
CAPPERS
PMC #RC1600, Capper Pluggers
Frain Industries, Carol Stream, IL 630-629-9900 (Fax 630-629-6575) Dave Eggleston
Resina #S30, Capper, 1 Head (Capper)
Frain Industries, Carol Stream, IL 630-629-9900 (Fax 630-629-6575) Dave Eggleston
Resina #S30, Capper, 1 Head (Capper) (5)
Frain Industries, Carol Stream, IL 630-629-9900 (Fax 630-629-6575) Dave Eggleston
Resina #P2274, Capper Pluggers
Frain Industries, Carol Stream, IL 630-629-9900 (Fax 630-629-6575) Dave Eggleston
FILLING EQUIPMENT (Fillers)
Velcon #FVS5-K6949, Stainless Steel sgl.hd.pail filler, 15" x 24" ht.scale section, 15" x 24" roller conv, controls, A-B controllr, on stand, #48747 Show photo of item Show item detail
Federal Equipment Co, Cleveland, OH 216-271-3500 (Fax 216-271-5210) Joanne Parente
FORM, FILL, SEAL MACHINES
Rennco #101, L-Bar Sealer w/cup counter, to 60/min, 240 V, integrated Rennco #CCL cup counter/loader, #48689 Show photo of item Show item detail
Federal Equipment Co, Cleveland, OH 216-271-3500 (Fax 216-271-5210) Joanne Parente
Rennco #SFT-101, L-Bar Sealer w/cup counter, to 60/min, 240 V, integrated Rennco #CCLcup counter/loader, #48690 Show photo of item Show item detail
Federal Equipment Co, Cleveland, OH 216-271-3500 (Fax 216-271-5210) Joanne Parente
Sencorp, blister former & plastic packaging machine w/chiller, 1000 HP, #KC-2202
Equipment Recovery Corp, Willoughby, OH 440-942-3003 (Fax 440-942-8608) Kevin Klicman
SEALER, CARTON
3M #700A, type 19000, top & bottom tape heads, motorized conveyor, 115 V., #48738 (2) Show photo of item Show item detail
Federal Equipment Co, Cleveland, OH 216-271-3500 (Fax 216-271-5210) Joanne Parente
PAINT & POWDER SYSTEMS & EQUIPMENT
BOOTHS, PAINT & POWDER
JBI #IDB-87, spray booths, walk-in paint booth, filter system, approx: 8' Wx9'Dx7'H, 2000 Show photo of item
Machinery Network Inc, Encino, CA 310-826-4440 (Fax 818-788-2470) Sales Dept.
PHARMACEUTICAL EQUIPMENT & SUPPLIES
DEDUSTERS, PHARMACEUTICAL
Pharma Tech #PTGV1000ST, dedust/metal check combo, vert.rotating brush deduster, 110 V, 2006, (4) #48831 Show photo of item Show item detail
Federal Equipment Co, Cleveland, OH 216-271-3500 (Fax 216-271-5210) Joanne Parente
Pharma Tech #PTGV1000ST, dedust/metal check combo, Stainless Steel, 3.75" W x 1.5" H apperture, reject, 110 V, 2006, #48827 Show photo of item Show item detail
Federal Equipment Co, Cleveland, OH 216-271-3500 (Fax 216-271-5210) Joanne Parente
PLANERS, DOUBLE HOUSING (Also See Millers, Planer Type)
69" x 78" x 14' Rockford, 5x14' tbl, 2 rail heads, 2 side heads, 60 HP motor/pump, in use Show photo of item
Belter Machinery, Rockford, IL 815-654-3300 (Fax 815-633-3969) Gary Belter
PLASTIC & RUBBER MACHINERY & EQUIPMENT
EXTRUDERS & EXTRUSION LINES
1.5" Killion, extruder, 14:1 L/D ratio, air cooled, s/n #16645, 15 HP, used, #8453 Show photo of item Show item detail
Arlington Plastics Machinery, Elk Grove Village, IL 847-956-7300 (Fax 847-956-8585) Sales
5" Reimelt #R57ESP, Stainless Steel continuous delumper crammer feeder, jktd. 1-bar @ 50° C, 3 KW motor drive, #48893 Show photo of item Show item detail
Federal Equipment Co, Cleveland, OH 216-271-3500 (Fax 216-271-5210) Joanne Parente
52" Vulcan #TWQ422, Sgl. turret 2-position winder, 62" W, 3" cores, up to 24" diameter rolls, controls, #48726 Show photo of item Show item detail
Federal Equipment Co, Cleveland, OH 216-271-3500 (Fax 216-271-5210) Joanne Parente
EXTRUSION DIES
29" Flex Lip Sheet Die, back center feed, dual R-bars, removable lower lip, manual deckling, #48685 (2) Show photo of item Show item detail
Federal Equipment Co, Cleveland, OH 216-271-3500 (Fax 216-271-5210) Joanne Parente
29" EDI Ultraflex #H-75, Flexable Flex Lip Sheet Die, Serial #81-4713/WELEX, #48722 Show photo of item Show item detail
Federal Equipment Co, Cleveland, OH 216-271-3500 (Fax 216-271-5210) Joanne Parente
GRANULATORS, PELLETIZERS (GRINDERS PLASTIC SCRAP)
8.75" x 10" IMS #A86-SP, plastic granulator, three phase motors & controls, 7.5 HP, s/n #A8630323 Show photo of item Show item detail
Hoff Online Auctions, Minneapolis, MN 612-521-5500 (Fax 612-331-3291) Denny Hoff
10" x 10" Foremost #HDI, plastic granulator, three phase motor & controls, 5 HP, s/n #6400 Show photo of item Show item detail
Hoff Online Auctions, Minneapolis, MN 612-521-5500 (Fax 612-331-3291) Denny Hoff
10" x 12" Cumberland #1012, plastic granulator, three phase motor & controls 7.5 HP, s/n #25086-6342 Show photo of item Show item detail
Hoff Online Auctions, Minneapolis, MN 612-521-5500 (Fax 612-331-3291) Denny Hoff
10" x 12" Mitts & Merril, plastic granulator, three phase motor & controls, 7.5 HP, s/n #GM7120 Show photo of item Show item detail
Hoff Online Auctions, Minneapolis, MN 612-521-5500 (Fax 612-331-3291) Denny Hoff
10" x 24" Plastic granulator, powered auger discharge, wooden operator' s stand 3 phase motor & controls, 25 HP Show photo of item Show item detail
Hoff Online Auctions, Minneapolis, MN 612-521-5500 (Fax 612-331-3291) Denny Hoff
MIXERS-BLENDERS & AGITATORS (Also See Chemical, Petroleum, Gas & Processing Eqpt.)
Maguire #960, gravametric blender, (6)components, s/n #82076, used, #8210 Show photo of item
Arlington Plastics Machinery, Elk Grove Village, IL 847-956-7300 (Fax 847-956-8585) Sales
Maguire #WSB940T, (4)component, 8.5 Amp, s/n #84889, 110 V., #8448 Show photo of item
Arlington Plastics Machinery, Elk Grove Village, IL 847-956-7300 (Fax 847-956-8585) Sales
MOLDING MACHINES, INJECTION, SCREW TYPE, PLASTIC
55 Ton, 2 oz., Van Dorn #55-RS-2, horizontal plastic injection, 13" clamp stroke, 20" daylight, 15 HP, s/n #8961-6, 1989 Show photo of item Show item detail
Hoff Online Auctions, Minneapolis, MN 612-521-5500 (Fax 612-331-3291) Denny Hoff
150 Ton, 8 oz., Van Dorn #150-RS-8F, horizontal plastc injection, 13" clamp stroke, 29" daylight, 25 HP, s/n #150RS8FVV2201, '87 Show photo of item Show item detail
Hoff Online Auctions, Minneapolis, MN 612-521-5500 (Fax 612-331-3291) Denny Hoff
300 Ton, 24 oz., Van Dorn #300HT1220-3259, 24" clamp str., vintage, 2000, #8461
Arlington Plastics Machinery, Elk Grove Village, IL 847-956-7300 (Fax 847-956-8585) Sales
350 Ton, 14 oz., Van Dorn #350-RS-14F, horizontal plastic injection, 11" clamp stroke, 48.5" daylight, s/n #1378, 50 HP, 1988 Show photo of item Show item detail
Hoff Online Auctions, Minneapolis, MN 612-521-5500 (Fax 612-331-3291) Denny Hoff
350 Ton, 20 oz., Van Dorn #350-RS-20F, horizontal plastic injection, 11" clamp stroke, 48.5" daylight, s/n #1355, 1988 Show photo of item Show Video of Item Show item detail
Hoff Online Auctions, Minneapolis, MN 612-521-5500 (Fax 612-331-3291) Denny Hoff
400 Ton, Lombard, horizontal plastic injection, hyraulic clamp, 38" x38.5" platen, 24" x24" distance btwn.tie bars, s/n #70-744 Show photo of item Show item detail
Hoff Online Auctions, Minneapolis, MN 612-521-5500 (Fax 612-331-3291) Denny Hoff
500 Ton Mir Plastic Model RMPV-BS520-1, 64 oz injection shot capacity, 29.5" x 19.5" tie bar clearance, 2001, #27421 Show photo of item Show item detail
Mohawk Machinery Inc, Cincinnati, OH 513-771-1952 (Fax 513-771-5120) Mr.Secord
650 Ton, 70 oz., Farrel #RS70-650, horizontal plastic injection, hydraulic clamp, 62.5" daylight, 120 HP, s/n #69WP4883-2 Show photo of item Show item detail
Hoff Online Auctions, Minneapolis, MN 612-521-5500 (Fax 612-331-3291) Denny Hoff
VACUUM FORMERS & THERMOFORMERS
Brown #T-300, trim press, 11.75" x 37.5" W cutting window, dr.by 10 HP DC motor, canopy, control.panel, 480 V., #48723 Show photo of item Show item detail
Federal Equipment Co, Cleveland, OH 216-271-3500 (Fax 216-271-5210) Joanne Parente
Lyle Inc. #125FT, thermoformer, dual form.stations, 29" W x 25" L platens, 5" str, 7' L oven, control.panel, 7.5 HP hyd.pump, #48724 Show photo of item Show item detail
Federal Equipment Co, Cleveland, OH 216-271-3500 (Fax 216-271-5210) Joanne Parente
PRESSES, FINNED TUBE
60 Ton, Oak #FP2, fin press, 1.5" stroke, 133-350 SPM, 9" -13" SH, 42" x34" bed, 1999, S33646 Show photo of item Show item detail
Perfection Machinery Sales, Elk Grove Village, IL 847-427-3333 (Fax 847-427-8884) Sales Dept.
PRESSES, FORMING
630 Ton, Peltzer & Ehlers Polymaster, 4-station hot forming press Show photo of item Show item detail
Hilco Industrial LLC, Farmington Hills, MI 248-419-1964 (Fax 248-254-9995) Ken Planet
PRESSES, GAP FRAME, SINGLE CRANK
50 Ton, Rockford #5-1/2S, gap frame press Show photo of item Show item detail
Netmachinery Inc., Mooresville, NC 704-660-8130 (Fax 704-663-3475) David Kragh
PRESSES, HIGH SPEED & AUTOMATIC
50 Ton, Benchmaster #5048, high speed press, 2-post design, 3" stroke, 48" x15-1/2" bed, 80 SPM, air clutch & brake, auto lube, #5735 Show photo of item
Sterling Machinery Exchange, South El Monte, CA 626-444-0311 (Fax 626-443-9588) Adam Mattes
PRESSES, HYDRAULIC (Also See Presses, Laminating and Presses, Molding)
35 Ton, DiAcro hydraulic press brake w/back gauge, 6' OA, USA made iron, excellent Show photo of item Show Video of Item Show item detail
Rohner Machinery Sales Inc, Fullerton, CA 888-440-4460 (Fax 714-441-1557) Chris Rohner
100 Ton, Pacific #100-10, hydraulic press brake, 10' OA, electric foot pedal, auto lube system, emergency stop, #A3712 Show photo of item Show Video of Item
Sterling Machinery Exchange, South El Monte, CA 626-444-0311 (Fax 626-443-9588) Adam Mattes
135 Ton, Pacific #J135-10, hyd.press brake, 10' OA, material supports, foot pedal, T-slotted bed, ram mounted palm control, #A3642 Show Video of Item
Sterling Machinery Exchange, South El Monte, CA 626-444-0311 (Fax 626-443-9588) Adam Mattes
200 Ton, Bentler, hyd., 4-post, down-act, 50" FB x 85" LR bed area, 28" SH, 37" stroke Show photo of item
Affordable Machinery, Grand Rapids, MI 616-200-4308 (Fax 269-623-5076) David Dimond
300 Ton, Pacific #225-OBL-14/48, straight side hydraulic press, 12" stroke, 20" DL, 174" x48" bed area, flush floor, 1998, #13341J
Timco Inc, Columbia, TN 931-381-1900 (Fax 931-381-5151) Kris Irvin
PRESSES, MOLDING COMPRESSION HYDRAULIC (Also See Presses, Laminating)
100 Ton, Wabash, 24" x24" elec.platens, 18" DL, 14" str, (2) 7" bore cyls, 5 HP, relay controls (4) Show photo of item
Icon Industries, Inc, Grand Rapids, MI 616-241-1877 (Fax 616-241-5578) Tom,Pete,Bob
PRESSES, O.B.I., BACK GEARED, SINGLE CRANK
32 Ton, Heim #3-GA, OBI punch press, 3" stroke, Heim PLC controller, air clutch & brake, dual palm control, one shot lube, #A3656 Show photo of item Show Video of Item
Sterling Machinery Exchange, South El Monte, CA 626-444-0311 (Fax 626-443-9588) Adam Mattes
60 Ton, Rousselle #6, 5" stroke, 3.5" manual RAM adj., 10.5" SH, 18" x30" bed, 10" throat, 50 SPM, 5 HP, s/n #15695 Show photo of item Show Video of Item Show item detail
Hoff Online Auctions, Minneapolis, MN 612-521-5500 (Fax 612-331-3291) Denny Hoff
60 Ton, Rousselle #6, 5" stroke, 3.5" manual RAM adj., 10.5" SH, 18" x30" bed, 10" throat, 50 SPM, 5 HP, s/n #15800 Show photo of item Show Video of Item Show item detail
Hoff Online Auctions, Minneapolis, MN 612-521-5500 (Fax 612-331-3291) Denny Hoff
121 Ton, Sutherland, 4" str, 12.6" SH, 43.5" x21" bed, 100spm, Wintriss SmartPac, '95, #sr4734 Show photo of item Show item detail
Alma Machinery Co Inc, Columbia, TN 615-369-7788 (Fax 615-369-7789) Ken King
PRESSES, O.B.I., FLYWHEEL, SINGLE CRANK
10 Ton, Sangiacomo #T10CE, OBI Eccentric Gooseneck C-frame punch press, 1" stroke, air clutch, foot pedal, stroke counter, #A3284 Show photo of item
Sterling Machinery Exchange, South El Monte, CA 626-444-0311 (Fax 626-443-9588) Adam Mattes
15 Ton, Rousselle #2E, OBI punch press, 3" stroke, dual palm buttons, One Shot lube system, stroke counter, #A3658 Show photo of item Show Video of Item
Sterling Machinery Exchange, South El Monte, CA 626-444-0311 (Fax 626-443-9588) Adam Mattes
22 Ton, Marshalltown #3, 2.5" stroke, 2" manual RAM adj., 13-1/4" x20-5/8" bed, 10-3/8" SH, 5-7/8" throat, foot pedal, 3 HP Show photo of item Show item detail
Hoff Online Auctions, Minneapolis, MN 612-521-5500 (Fax 612-331-3291) Denny Hoff
25 Ton, Rousselle #3E, punch press Show photo of item Show item detail
Manufacturing Solutions, Costa Mesa, CA 714-545-0940 (Fax 310-943-3550) Mike Dieveney
25 Ton, Rousselle #3E, OBI punch press Show photo of item Show item detail
Manufacturing Solutions, Costa Mesa, CA 714-545-0940 (Fax 310-943-3550) Mike Dieveney
25 Ton, Rousselle #3E, OBI punch press Show photo of item Show item detail
Manufacturing Solutions, Costa Mesa, CA 714-545-0940 (Fax 310-943-3550) Mike Dieveney
35 Ton, Bliss #C35, 3" stroke, 10.75" SH, 9" throat, air clutch & brake, '77, #6908
Fabricating Machinery Corp, Duarte, CA 626-359-0024 (Fax 626-359-4055) Scott Courneya
60 Ton, Bliss #C60, 4" stroke, 15.75" SH, 100 SPM, air clutch & brake, 1969, #9764 Show item detail
Turner Industries Inc, Grand Rapids, MI 616-949-5910 (Fax 616-949-3461) Jeff/Bill/David
75 Ton, Minster #7, OBI press, 3" stroke, 4" ram adjustment, 15.5" DL, 150 SPM, 36" x24" bed area, air clutch & brake, #13303J Show photo of item
Timco Inc, Columbia, TN 931-381-1900 (Fax 931-381-5151) Kris Irvin
PRESSES, ROTARY (TABLET)
6.5 Ton, Manesty Mark IIA, keyed upper guides, 61 sta, 7/16" max. dia, 11/16" depth fill, dual side, 11100 tabs/min, 1964, #48834 Show photo of item Show item detail
Federal Equipment Co, Cleveland, OH 216-271-3500 (Fax 216-271-5210) Joanne Parente
Fette, 73 Station Tablet Press Turret for #3090I Press, Keyed Upper Punch Guides On Cart, #48839 Show photo of item Show item detail
Federal Equipment Co, Cleveland, OH 216-271-3500 (Fax 216-271-5210) Joanne Parente
Manesty Mark #IIA, 61 Station Tablet Press Turret, Keyed, #48838 Show photo of item Show item detail
Federal Equipment Co, Cleveland, OH 216-271-3500 (Fax 216-271-5210) Joanne Parente
PRESSES, STRAIGHT SIDE, DOUBLE CRANK (Single Action)
100 Ton, Bliss #S2-100-60-36, SSDC press, 8" stroke, 20-1/2" SH (SDAU), 40-80 SPM, 60" x36" bed area, air clutch & brake, 1968, #13338J
Timco Inc, Columbia, TN 931-381-1900 (Fax 931-381-5151) Kris Irvin
150 Ton, Heim #S2-150-48x102, 8" str, 26" SDAU, 102x48" bed, A/C, bolster plate, '80, #M9592 Show photo of item
Universal Press & Machy Inc, Clinton Township, MI 586-569-0150 (Fax 586-569-0103) Sales Dept.
150 Ton, Niagara #SE2-150-60-36, SSDC press, 6" stroke, 27" SH, 50-100 SPM, 60" x36" bed area, air clutch & brake, 1994, #13339J
Timco Inc, Columbia, TN 931-381-1900 (Fax 931-381-5151) Kris Irvin
200 Ton, Niagara #SC2-200, 96" x48" bed, 12" str, 44" SH, 20-40 SPM, floor stand, 1990, #9587 Show photo of item Show Video of Item Show item detail
Universal Press & Machy Inc, Clinton Township, MI 586-569-0150 (Fax 586-569-0103) Sales Dept.
200 Ton, Niagara #SC2-200, 96" x48" bed, 12" str, 44" SH, 20-40 SPM, floor stand, 1986, #9588 Show photo of item Show item detail
Universal Press & Machy Inc, Clinton Township, MI 586-569-0150 (Fax 586-569-0103) Sales Dept.
220 Ton, Komatsu #E2G200, 98.4" x47.2" bed, 11.81" str, 40" die hgt, 20-45 SPM, 2000, #9591 Show photo of item Show Video of Item
Universal Press & Machy Inc, Clinton Township, MI 586-569-0150 (Fax 586-569-0103) Sales Dept.
250 Ton, Niagara #PN-250-72-36, SSDC press, 6" stroke, 20" SH, 35 SPM, 72" x36" bed area, air clutch & brake, 1987, #13340J Show photo of item
Timco Inc, Columbia, TN 931-381-1900 (Fax 931-381-5151) Kris Irvin
300 Ton, Bliss #SC2-300, 48" x 60" bed, 10" stroke, 30-60 SPM, air clutch
Planet Machinery Co, Pontiac, MI 248-335-8330 (Fax 248-335-3680) Ken/ Chris
330 Ton, Verson #2W 1080 Show photo of item Show item detail
RAAR Group, Redondo Beach, CA 310-487-3800 (Fax 702-947-6320) Rick Schotts
350 Ton, Simpac #MC2-350, 11.8" stroke, 106" x47" bolster area, 4.75" slide adj, 2010 Show photo of item Show item detail
Wheeler Machinery Sales, Pomona, CA 888-589-6721 (Fax 909-348-5617) Dan Wheeler
440 Ton, Komatsu Eccentric #E2G-400U, 16" str, 36" SH, 122" x61" bed, 20-40spm, '94, #sr4570 Show photo of item Show item detail
Alma Machinery Co Inc, Columbia, TN 615-369-7788 (Fax 615-369-7789) Ken King
800 Ton, Aida #NL4-730, SSDC, 98" x 120" , 23.6" stroke, 54" SH, installed 1986, #10180 Show photo of item
Jordan Craig Machinery Intl L, New City, NY 845-398-0073 (Fax 845-398-0074) Jordan Craig
PUMPS
CENTRIFUGALS (Including Boiler Feed Pumps)
1500 GPM @ 140' TDH, Goulds #3196, 316 Stainless Steel, 8" x 6" x 12" impeller, on base, 100 HP, 460 V. motor, #48845 Show photo of item Show item detail
Federal Equipment Co, Cleveland, OH 216-271-3500 (Fax 216-271-5210) Joanne Parente
1500 GPM @ 140' TDH, Goulds #3196, 316 Stainless Steel, 8" x 6" x 12" impeller, on base, 100 HP, 460 V. motor, #48846 Show photo of item Show item detail
Federal Equipment Co, Cleveland, OH 216-271-3500 (Fax 216-271-5210) Joanne Parente
Fristam #FPR742-146, Stainless Steel Centrifugal Pump, 2.5" x 2" , 5 HP, 208-230/460 V., 3510 RPM, #48896 Show photo of item Show item detail
Federal Equipment Co, Cleveland, OH 216-271-3500 (Fax 216-271-5210) Joanne Parente
Fristam #FPX3532-175, Stainless Steel Centrifugal Pump, 3" x 2" , 15 HP, 208-230/460 V., #48898 Show photo of item Show item detail
Federal Equipment Co, Cleveland, OH 216-271-3500 (Fax 216-271-5210) Joanne Parente
Fristam #FPX701-90, Stainless Steel, " X" , 1.5 HP, 230/460 V. motor, Ser. #FPX701-0106695, #48824 Show photo of item Show item detail
Federal Equipment Co, Cleveland, OH 216-271-3500 (Fax 216-271-5210) Joanne Parente
Goulds, Self-Priming C/S Centrifugal Pump, 2" x 1.5" on base w/1.5 HP, 460 V. motor, #34581 Show photo of item Show item detail
Federal Equipment Co, Cleveland, OH 216-271-3500 (Fax 216-271-5210) Joanne Parente
Goulds, Self-Priming C/S Centrifugal Pump, 2" x 1.5" on base w/1.5 HP, 460 V. motor, #34582 Show photo of item Show item detail
Federal Equipment Co, Cleveland, OH 216-271-3500 (Fax 216-271-5210) Joanne Parente
KSB #HGC 2/9, with Siemens 350 HP motor, #BU-3 (4)
Equipment Recovery Corp, Willoughby, OH 440-942-3003 (Fax 440-942-8608) Kevin Klicman
Leybold-Heraeus #TR-630, centrifugal pump, 20 HP, #DS-1017
Equipment Recovery Corp, Willoughby, OH 440-942-3003 (Fax 440-942-8608) Kevin Klicman
Summit #2196, Stainless Steel, 1" x 1.5" x 6" impeller, 150 psi on base w/2 HP , 230/460 V. motor, #48768 Show photo of item Show item detail
Federal Equipment Co, Cleveland, OH 216-271-3500 (Fax 216-271-5210) Joanne Parente
Waukesha Cherry Burrel #2065, Stainless Steel, Centrifugal, 2.5" x 2" , 7.5 HP, 208-230/460 V., #48894 Show photo of item Show item detail
Federal Equipment Co, Cleveland, OH 216-271-3500 (Fax 216-271-5210) Joanne Parente
Waukesha Cherry Burrel #2065, Stainless Steel, Centrifugal, 2" x 1.5" , 5 HP, 208-230/460 V., #48895 Show photo of item Show item detail
Federal Equipment Co, Cleveland, OH 216-271-3500 (Fax 216-271-5210) Joanne Parente
Waukesha Cherry Burrel #2065IV, Stainless Steel, Centrifugal, 2" x 1.5" , 10 HP, 208-230/460 V., #48897 Show photo of item Show item detail
Federal Equipment Co, Cleveland, OH 216-271-3500 (Fax 216-271-5210) Joanne Parente
Waukesha Cherry Burret #2065, Stainless Steel, 2.5" x 2" , 3 HP, 208-230-460 V. motor, #48798 Show photo of item Show item detail
Federal Equipment Co, Cleveland, OH 216-271-3500 (Fax 216-271-5210) Joanne Parente
POSITIVE DISPLACEMENT PUMPS
80 GPM @ 203 psi, Viking #K4124A, C/I fuel pump mounted on steel base, 5 HP @ 1800 RPM Show photo of item Show item detail
U S Combustion Products Inc, Ketchum, ID 208-788-9367 (Fax 208-788-9368) S.Backstatter
APV #MP-2H/036/20, Stainless Steel rotary Lobe, 2" inlet/outlet, 5 HP, 230/460 V.motor, #48772 Show photo of item Show item detail
Federal Equipment Co, Cleveland, OH 216-271-3500 (Fax 216-271-5210) Joanne Parente
Unibloc Type PD, rotary glove pump, Stainless Steel, 3" inlet/outlet, 5 HP, 230/460 V. motor, #48773 Show photo of item Show item detail
Federal Equipment Co, Cleveland, OH 216-271-3500 (Fax 216-271-5210) Joanne Parente
ROTARY VANE PUMPS (NOT VACUUM)
4" Waukesha #220U2, Stainless Steel Rotary Lobe Pump, S/S, 4" inlet/outlet, on base, 30 HP, 460 V.motor, #48795 Show photo of item Show item detail
Federal Equipment Co, Cleveland, OH 216-271-3500 (Fax 216-271-5210) Joanne Parente
VACUUM PUMPS
Nash #904U2, rebuilt
Engineered Coatings & Machine, Birmingham, AL 205-856-3700 (Fax 205-856-3740) Ed Delorme
MISCELLANEOUS, PUMPS
3.5" Dynisco #MSDP300, undriven driven w/15 HP AC motor thru 25.62:1 gearbox, 54" center line hgt, VFD controller, #48686 Show photo of item Show item detail
Federal Equipment Co, Cleveland, OH 216-271-3500 (Fax 216-271-5210) Joanne Parente
3.5" Dynisco #MSDP300, undriven driven w/15 HP AC motor thru 25.62:1 gearbox, 54" center line hgt, VFD controller, #48688 Show photo of item Show item detail
Federal Equipment Co, Cleveland, OH 216-271-3500 (Fax 216-271-5210) Joanne Parente
RIVETERS
Chicago Rivet & Machine Co., power rivet machine, 24" throat, #4084 Anvil, #139 Jaws, #1046 Driver, foot pedal, s/n #140-1078 Show photo of item Show item detail
Hoff Online Auctions, Minneapolis, MN 612-521-5500 (Fax 612-331-3291) Denny Hoff
Chicago #CP-0625-24, compression riveter, stand, adjustable operating speed, #A3688 Show photo of item Show Video of Item
Sterling Machinery Exchange, South El Monte, CA 626-444-0311 (Fax 626-443-9588) Adam Mattes
Chicago Rivet & Machine Co., power rivet machine, 24" throat, 3/16" cap., foot pedal, 1/3 HP, s/n #140-1186-88 Show photo of item Show item detail
Hoff Online Auctions, Minneapolis, MN 612-521-5500 (Fax 612-331-3291) Denny Hoff
National #600, power rivet machine, 12" throat, foot pedal, single phase motor & controls, s/n #450 Show photo of item Show item detail
Hoff Online Auctions, Minneapolis, MN 612-521-5500 (Fax 612-331-3291) Denny Hoff
Riveter, #7987 (9) Show photo of item
Sterling Machinery Exchange, South El Monte, CA 626-444-0311 (Fax 626-443-9588) Adam Mattes
ROBOTS, INDUSTRIAL
Motoman Arcworld 1000, robotic weld cell, 60" dia 2 pos rotary tbl, recently refurb, 2004 Show photo of item
Surplus Asset Auctions LLC, Barrington, IL 630-690-7986 (Fax 630-690-7795) Mike Gordon
Motoman Arcworld 1000, robotic weld cell, 6-Axis, 52" reach, MRC control, 1998 Show photo of item
Surplus Asset Auctions LLC, Barrington, IL 630-690-7986 (Fax 630-690-7795) Mike Gordon
Panasonic #VR005, CII controller
New Age Robotics & Controls, Ayr, ON 519-621-3333 (Fax 519-621-3380) Cornel Cosma
ROLLFORMERS (Also See Sheet Metal Machinery)
18 Stand, Yoder #M2-1/2, rollformer, 2.5" arbor, 15" roll space, 60 HP, 18 pass, 1999, #63673 Show photo of item Show item detail
Yoder Machinery Sales, Holland, OH 800-622-4463 (Fax 419-865-5557) Sales
20 Stand, Yoder #M2-1/2, rollformer, 2.5" arbor, 15" roll space, 60 HP, 20 pass, 2000, #63672 Show photo of item Show item detail
Yoder Machinery Sales, Holland, OH 800-622-4463 (Fax 419-865-5557) Sales
ROLLS, ANGLE BENDING
3" X 3" Buffalo Model #10 Hydraulic, Vertical, 3 roll drive, guide roll attachment, new never used, manuals, 1993 Show photo of item
Spier Machinery Corp, North Tonawanda, NY 716-694-4711 (Fax 716-694-0627) Paul Shear
4" x 4" x 1/2" Davi, CNC, MC4P, double pinch, angle guides only has 15 hrs, 2008 Show photo of item Show Video of Item Show item detail
Pacific Machine Tools LLC, Carlsbad, CA 760-431-3560 (Fax 760-431-3562) Maury Cohn
ROLLS, PLATE BENDING, INITIAL & DOUBLE PINCH TYPE
6' X1/2" Pullmax, 10-5/8" diameter Rolls, Hyd.Drop, Cone, 1981 S33655 Show photo of item Show item detail
Perfection Machinery Sales, Elk Grove Village, IL 847-427-3333 (Fax 847-427-8884) Sales Dept.
8' x 1" Imcar #2550+25, 3-roll, 15" top roll, 100" roll length, 40 HP, hyd.rolls, pedestal, '70 Show photo of item Show item detail
Westbrook Engineering Co, Warren, MI 866-367-7297 (Fax 586-759-3106) Sales Dept.
SANDERS (Also See Woodworking Machinery)
BELT SANDERS (Also See Grinders, Belt)
52" Timesaver #252-1C, vacuum conveyor, segmented platen, very nice, 1997
Advanced Jones Machinery Co, Dayton, OH 937-278-7337 (Fax 937-278-8234) Bob Gibson
DISC SANDERS (Also See Grinders, Belt)
30" Oliver #34-DD, double disc sander, includes Torit dust collector, #A3713
Sterling Machinery Exchange, South El Monte, CA 626-444-0311 (Fax 626-443-9588) Adam Mattes
SAWS, BAND, HORIZONTAL (Also See Vertical Band Saws)
10" x 10" Acra #HL-250, automatic feed, 1.25" blade, coolant
Heart Of Wisconsin Mchy Co, Nekoosa, WI 715-886-4926 (Fax 715-886-3016) Fred Parker
10" X 18" Johnson Model JH-10, 1" blade, coolant, 1HP, 220/440V, 50, 90, 160, 270 FPM Show photo of item
Spier Machinery Corp, North Tonawanda, NY 716-694-4711 (Fax 716-694-0627) Paul Shear
11" x 19" Cosen #SH500M, miter, 1" blade, semi-auto., full stroke hydraulic vise, coolant system, 3 HP, new, #28811 Show photo of item Show item detail
C.W. Wood Machinery Inc, Cincinnati, OH 800-745-6008 (Fax 513-542-4819) Sales Dept.
12" x 13" DoAll #C-1213A, horizontal saw, #10764 Show photo of item Show item detail
Vander Ziel Machinery Sales, Alto, MI 616-868-1111 (Fax 616-868-1115) Steve Vander Ziel
12.75" x 12.75" Hem #H101A-1, auto barfeed, 1-1/4" blade, 5 HP, 60-350 SPM, #4448
Diamond Jack Machinery Inc, Fort Smith, AR 479-785-2554 (Fax 479-785-4362) Jack Yancey
13" x 18" Hyd-Mech #S-20 Series II, horizontal saw, #10233 Show photo of item Show item detail
Vander Ziel Machinery Sales, Alto, MI 616-868-1111 (Fax 616-868-1115) Steve Vander Ziel
14" x 14" Behringer #HBP-360A, fully automatic heavy duty dual column horizontal band saw, coolant system, #A3667
Sterling Machinery Exchange, South El Monte, CA 626-444-0311 (Fax 626-443-9588) Adam Mattes
14" x 14" Hyd-Mech #H-14A, auto.feed, 1.25" blade, 19" wheel diameter , 25 gal.coolant tank, 7.5 HP, s/n #50301353, 2001, #28797 Show photo of item Show item detail
C.W. Wood Machinery Inc, Cincinnati, OH 800-745-6008 (Fax 513-542-4819) Sales Dept.
14" x 16" HEM #H-105A, automatic heavy horizontal band saw, adjustable, flood coolant system, bundling attachment, #A3670
Sterling Machinery Exchange, South El Monte, CA 626-444-0311 (Fax 626-443-9588) Adam Mattes
18" x 16" Hyd-Mech #S23, 1-1/4" bld, 16" round, 40°miter, 5 HP, flood clnt, infinite V/S, '00 Show item detail
Westbrook Engineering Co, Warren, MI 866-367-7297 (Fax 586-759-3106) Sales Dept.
18" x 27" Hyd-Mech #S-25A, horizontal band saw Show photo of item Show item detail
Manufacturing Solutions, Costa Mesa, CA 714-545-0940 (Fax 310-943-3550) Mike Dieveney
20" x 20" Amada #HFA500S, automatic horizontal saw, 1995, #11192 Show photo of item Show item detail
Vander Ziel Machinery Sales, Alto, MI 616-868-1111 (Fax 616-868-1115) Steve Vander Ziel
22" x 22" Hyd-Mech #H22A, fully auto, 2" bld, 10 HP, 40-300 SFM, o/head bundling, conveyors Show photo of item Show item detail
Westbrook Engineering Co, Warren, MI 866-367-7297 (Fax 586-759-3106) Sales Dept.
Kalamazoo #H9AWV, horizontal band saw Show photo of item Show item detail
Machinesused.com, Minneapolis, MN 763-745-1166 (Fax 651-315-8176) John Lawton
SAWS, BAND, VERTICAL (Also See Horizontal Band Saws)
12" Speeder #KB-30, vertical band saw, blade welder, blade shear, chip blower, work light, #A3247
Sterling Machinery Exchange, South El Monte, CA 626-444-0311 (Fax 626-443-9588) Adam Mattes
14" Leten #LCM-360, vertical band saw, blade welder, blade grinder, cut-off tool, 1/2 HP, #A2036 Show photo of item
Sterling Machinery Exchange, South El Monte, CA 626-444-0311 (Fax 626-443-9588) Adam Mattes
16" DoAll #V-16, vertical contour band saw, blade grinder, blade shear, blade welder, blade brush, chip blower, #A3708 Show photo of item Show Video of Item
Sterling Machinery Exchange, South El Monte, CA 626-444-0311 (Fax 626-443-9588) Adam Mattes
18" x 18" Marvel #8, vertical band saw, tilt frame, 1" blade cap, 33" x24-1/4" tbl, #1908 Show photo of item Show item detail
Charleston Annex Corporation, Indian Trail, NC 704-821-7370 (Fax 704-821-7392) Lance/ Mark
26" DoAll #2612-2H, vertical heavyduty contour band saw, hyd.table feed & tilt, s/n #206-65182, #A3668 Show Video of Item
Sterling Machinery Exchange, South El Monte, CA 626-444-0311 (Fax 626-443-9588) Adam Mattes
Powermatic #87, 20" diameter blade wheels, 19.75" throat, 24" x24" tilting table, 40-4500 FPM, 2 HP, s/n #182123 Show photo of item Show item detail
Hoff Online Auctions, Minneapolis, MN 612-521-5500 (Fax 612-331-3291) Denny Hoff
SAWS, COLD, FRICTION AND CARBIDE
4" KMT #C350SA, semi-automatic cold saw, Capacity: 4" round for ferrous material Show photo of item Show item detail
Netmachinery Inc., Mooresville, NC 704-660-8130 (Fax 704-663-3475) David Kragh
12-14" Imet / Kalamazoo #Record 315/350, 30/60 RPM, Ferrous, Mitre, 3.5 HP Show photo of item Show item detail
Destiny Machinery Inc, Odessa, FL 727-376-2399 (Fax 727-372-8202) Dennis Laliberte
20" Elumatec #SA142/25, Automatic, 5HP, Mitre, Non-Ferrous, (1998) Show photo of item Show item detail
Destiny Machinery Inc, Odessa, FL 727-376-2399 (Fax 727-372-8202) Dennis Laliberte
SHEARS, FOOT (Also See Sheet Metal Machinery)
16 ga. x 37" Grizzly #G-9948, foot shear, (2) front supports, manual back gauge, s/n #091201, #A3644 Show photo of item Show Video of Item
Sterling Machinery Exchange, South El Monte, CA 626-444-0311 (Fax 626-443-9588) Adam Mattes
16 ga. x 52" Pexto #152-K, foot shear, (2) front supports, manual back gauge, s/n #4346-9-89, #A3654 Show photo of item Show Video of Item
Sterling Machinery Exchange, South El Monte, CA 626-444-0311 (Fax 626-443-9588) Adam Mattes
SHEARS, POWER SQUARING AND PLATE (GAUGES)
16 Gauge x 52" Acra #FS-P5216-H, Hydraulic, Back Gauge, (2003) Show photo of item Show item detail
Destiny Machinery Inc, Odessa, FL 727-376-2399 (Fax 727-372-8202) Dennis Laliberte
16 ga. x 4' DiAcro #48, 50" blade, 5/16" blade rake, 120 SPM, 18" rear operated manual back gauge, 1.5 HP, s/n #EH-1021 Show photo of item Show Video of Item Show item detail
Hoff Online Auctions, Minneapolis, MN 612-521-5500 (Fax 612-331-3291) Denny Hoff
14 ga. x 4' Wysong #1452, power shear, ROMBG, square arm, front supports, one shot lube, s/n #P36-497, #9909 Show photo of item
Sterling Machinery Exchange, South El Monte, CA 626-444-0311 (Fax 626-443-9588) Adam Mattes
10 ga. x 6' Wysong #1072, power shear, #KK-6000
Equipment Recovery Corp, Willoughby, OH 440-942-3003 (Fax 440-942-8608) Kevin Klicman
SHEARS, POWER SQUARING AND PLATE (INCHES)
1/4" x 6' Accurshear #62506, hydraulic, FOBG w/DRO, electric foot pedal, stroke length control, front support, #A3717
Sterling Machinery Exchange, South El Monte, CA 626-444-0311 (Fax 626-443-9588) Adam Mattes
1/4" x 6' Pacific #76B-1/4, heavy duty Ultra Quiet power shear, FOPBG w/indicator, foot pedal, s/n #T-383T, #A3653 Show photo of item Show Video of Item
Sterling Machinery Exchange, South El Monte, CA 626-444-0311 (Fax 626-443-9588) Adam Mattes
1/4" x 10' Amada #M-3060, mechanical, FOPBG w/inch & metric RO, square arm, front supports, extra blades, s/n #30600483, #A3669 Show Video of Item
Sterling Machinery Exchange, South El Monte, CA 626-444-0311 (Fax 626-443-9588) Adam Mattes
1/4" x 10' Cincinnati #1810, mechanical, manual back gauge, sq.arm, 18" throat Show photo of item Show item detail
Wheeler Machinery Sales, Pomona, CA 888-589-6721 (Fax 909-348-5617) Dan Wheeler
1/4" x 10' Cincinnati #1810, FOPBG w/indicator, 126" squaring arm, foot pedal, (2) front supports, light, s/n #40333, #A3714 Show photo of item Show Video of Item
Sterling Machinery Exchange, South El Monte, CA 626-444-0311 (Fax 626-443-9588) Adam Mattes
1/4" x 10' Krras #RAS-306, hyd, Audemi sgl Axis NC control, 39" pwrd BG, vbl rake, vbl blade Show item detail
Westbrook Engineering Co, Warren, MI 866-367-7297 (Fax 586-759-3106) Sales Dept.
1/4" x 12' Cincinnati #1812, mechanical shear, #7889 Show photo of item Show item detail
Vander Ziel Machinery Sales, Alto, MI 616-868-1111 (Fax 616-868-1115) Steve Vander Ziel
3/8" x 12' Cincinnati #2512, 36" FOPBG Show photo of item Show item detail
Aleco Machinery Sales, Milwaukee, WI 414-264-5848 (Fax 414-264-3652) Alex Hawley
1/2" x 10' Cincinnati mechanical shear Show photo of item
Affordable Machinery, Grand Rapids, MI 616-200-4308 (Fax 269-623-5076) David Dimond
5/8" x 12' Cincinnati #5FL-12, hyd, 48" FOPBG, 12' sq.arm, (2) FSA, 40 HP, xtra set of blades Show photo of item Show item detail
Westbrook Engineering Co, Warren, MI 866-367-7297 (Fax 586-759-3106) Sales Dept.
SLITTING LINES
50" x .012" -.187" Nova, 40000 lb, 50k psi, 20" -24" coil ID, coil car, uncoiler, '05, #M9490 Show photo of item
Universal Press & Machy Inc, Clinton Township, MI 586-569-0150 (Fax 586-569-0103) Sales Dept.
SPLINE ROLLERS
No. 350S Anderson Cook, 48" spline roller Show photo of item Show item detail
Hilco Industrial LLC, Farmington Hills, MI 248-419-1964 (Fax 248-254-9995) Ken Planet
TAPPERS, For Internal Threading (Also See Drilling & Tapping Machines)
Leland-Gifford #2LMS, 26" swing, #3MT, 150-1800 RPM, (2)PF, 8 spindle, 1974, #2128 Show item detail
Turner Industries Inc, Grand Rapids, MI 616-949-5910 (Fax 616-949-3461) Jeff/Bill/David
TESTING EQUIPMENT (Also See Laboratory & Research Equipment)
ENVIRONMENTAL CHAMBERS
Tenney #T40C-10, -73°C to 200°C, (2) 6 HP compressors, R-404A & R-23, 40" x 40" x 44" D, TempGard control, 2005 Show photo of item
Surplus Machine Tool, Saint Paul, MN 651-283-7444 Dean Gabrielson
Tenney #T40C-10-SPL, -73°C to 200°C, (2) 6 HP Copeland compressors, R-404A & R-23, air cooled, VFD, 40" x 40" x 44" D, 2008 (4) Show photo of item
Surplus Machine Tool, Saint Paul, MN 651-283-7444 Dean Gabrielson
FREEZERS
Harris, Low-Temp Freezer, -80° C. One Used, #70149
Federal Equipment Co, Cleveland, OH 216-271-3500 (Fax 216-271-5210) Joanne Parente
Harris, Low-Temp Freezer, -80° C. One Used, #70149 Show photo of item Show item detail
Federal Equipment Co, Cleveland, OH 216-271-3500 (Fax 216-271-5210) Joanne Parente
THREADERS, PIPE (Includes Nipple Machines,Pipe & Tube Cutters)
1/8" -2" Rigid #535, 115 V., universal stand and tray, well equipped Show photo of item
J Hebert Machine Tool Co., Charlotte, NC 704-825-1511 Jon Hebert
1" Landis #1L, double head, 1/4" -1" bolt, 1/8" -1" pipe, s/n #1L606, 3 HP, #019911 Show photo of item Show item detail
Universal Metalworking Equip., Houston, TX 713-675-4145 (Fax 713-675-1294) M. Feinstein
TOOLING & ACCESSORIES
CHUCKS
39-1/4" 4-Jaw chuck, #9236 Show photo of item Show item detail
Vander Ziel Machinery Sales, Alto, MI 616-868-1111 (Fax 616-868-1115) Steve Vander Ziel
ROTARY TABLES (Also See Rotary Tables, CNC)
6.5" Fadal #VH-65, rotary table, control box, 1997, Loc Colorado Show photo of item Show item detail
Automatics & Machinery Co Inc, Longmont, CO 800-543-7666 (Fax 303-651-6556) Steve Beck
48" x 60" Giddings & Lewis Air Lift rotary table, (6) T-slots, #T01047 Show photo of item Show item detail
N & R Machine Sales, Navasota, TX 800-245-3194 (Fax 936-825-2679) Randy Nevels
60" x 60" Giddings & Lewis Air Lift rotary table, (6) T-slots, #T010410 Show photo of item Show item detail
N & R Machine Sales, Navasota, TX 800-245-3194 (Fax 936-825-2679) Randy Nevels
96" x 96" Kitchen & Wade, infeeding, 44800 lb cap., 72" infeed, 10 HP, 1968, #24955 Show photo of item Show item detail
Prestige Equipment Corp, Melville, NY 631-249-5566 (Fax 631-249-9494) Terry Lashin
TRACERS
4.5" Mimik #UT45, hydraulic tracer unit for engine lathes, tracer slide, 2-axis adj.slide, mounting adapter, #A3681
Sterling Machinery Exchange, South El Monte, CA 626-444-0311 (Fax 626-443-9588) Adam Mattes
VIBRATORY FINISHERS
30 cu.ft. Roto Finish Oval Racetrack Tub Type, Mdl OVF 16-30, vibratory, 16" chamber width, 20HP, #27434 Show photo of item Show item detail
Mohawk Machinery Inc, Cincinnati, OH 513-771-1952 (Fax 513-771-5120) Mr.Secord
44 cu.ft. Giant Finishing FT-44, vibratory, 28" tub diam, 9600 lb load cap, 25HP, #27433 Show photo of item Show item detail
Mohawk Machinery Inc, Cincinnati, OH 513-771-1952 (Fax 513-771-5120) Mr.Secord
Vibratory finisher & dryer sys, complete, Torex #T9060 vibratory, #T6020-D dryer new'05 Show photo of item Show item detail
Naab Sales Corporation, Hopkins, MN 952-933-6755 (Fax 952-933-7229) J.Van Heuveln
WASHING MACHINES, (Also See Degreasers)
Artuna belt type washer Show photo of item Show item detail
Hilco Industrial LLC, Farmington Hills, MI 248-419-1964 (Fax 248-254-9995) Ken Planet
Hurricane Midbrook belt washer, 18" W x 12" open, all SS, gas fired, wash & blow off Show photo of item
Furnaces, Ovens & Baths, Inc, Clarkston, MI 248-625-7400 (Fax 248-625-4030) Jeffrey Hynes
Panther Ind. Stinger 3 Plus, pressure washer, hot & cold, 2000 psi, 220 V., s/n #303-129
Quality Rebuilding Corp, Valparaiso, IN 219-476-0281 (Fax 219-476-0283) Stu Smith
WELDING MACHINERY & EQUIPMENT
ARC WELDERS
Miller Syncrowave 350, AC/DC Arc welding power source Show photo of item Show item detail
Miedema Auctioneering & Appraisals Inc, Byron Center, MI 616-538-0367 (Fax 616-538-5230) Amada Bowers
BUTT & FLASH WELDERS
Sciaky #BPR-05-50H, 50 KVA, standard dual act, 7500#clamp, 5000#upset force, 440V., #5615 Show photo of item
T J Snow Co Inc, Chattanooga, TN 800-669-7669 (Fax 423-892-3889) Tom Snow
MIG WELDERS
Lincoln CV-655, 650a/44v/100%, 70-815 Amps; S33635 Show photo of item Show item detail
Perfection Industrial Sales, Elk Grove Village, IL 847-427-3333 (Fax 847-427-8884) Dept. Sales
PROJECTION WELDERS
50 KVA Taylor-Winfield #ENE-18-50, 6" x6" platen, 18" thrt, standard dual act, 220V., #5640 Show photo of item
T J Snow Co Inc, Chattanooga, TN 800-669-7669 (Fax 423-892-3889) Tom Snow
SPOT, ROCKER ARM WELDERS
20 KVA Acme #2-24-20, spot welder, Robotron control, s/n #4496, #8955 Show photo of item
Sterling Machinery Exchange, South El Monte, CA 626-444-0311 (Fax 626-443-9588) Adam Mattes
30 KVA Rex, 6 different amp.ctrl settings, 28" thrt, W/C, pneu.operated arms, foot switch Show Video of Item Show item detail
Naab Sales Corporation, Hopkins, MN 952-933-6755 (Fax 952-933-7229) J.Van Heuveln
WIRE MACHINERY
FORMERS, WIRE
Phoenix #VS305 CNC Vertislide, .023-.118" wire, 1.5" x.039" flat stock, 2-Ax., 7 slides, '04
R & R Machinery & Rebuilding, Forestville, CT 860-584-8226 (Fax 860-583-8319) Richard Dahlen
SPRING COILERS, TORSION, WIRE
No. 721 Sleeper & Hartley, spring coiler wire machine, .018" -.080" cap., Reliance variable speed drive, tooling, #A2535 Show photo of item
Sterling Machinery Exchange, South El Monte, CA 626-444-0311 (Fax 626-443-9588) Adam Mattes
STRAIGHTENERS & CUT OFF, WIRE
3/16" Nilson #S-3, 4-slide, s/n #85950, 1968, #7532
Sterling Machinery Exchange, South El Monte, CA 626-444-0311 (Fax 626-443-9588) Adam Mattes
5/8" Lewis #10F, travel cut, 12' cut-off
Victory Machinery Exchange, Lake Forest, IL 847-918-9797 (Fax 847-918-9733) Bob or Neal
Electric & Power Section
BOILERS, FIRETUBE
47.5 HP Superior, 200 psi, gas, 9 ppm, new (complete with pre-piped feedwater system & blowdown tank)
Nationwide Boiler Inc, Fremont, CA 800-227-1966 (Fax 510-490-0571) Larry Day
119 HP Superior, 200 psi, gas, 9 ppm, new (complete with pre-piped feedwater system & blowdown tank)
Nationwide Boiler Inc, Fremont, CA 800-227-1966 (Fax 510-490-0571) Larry Day
350 HP Cleaver-Brooks, 125 psi, gas/#2 oil, 9 ppm, 2006
Nationwide Boiler Inc, Fremont, CA 800-227-1966 (Fax 510-490-0571) Larry Day
475 HP Superior, 250 psi, gas, 9 ppm, new
Nationwide Boiler Inc, Fremont, CA 800-227-1966 (Fax 510-490-0571) Larry Day
BOILERS, WATERTUBE
110, 000 PPH Babcock & Wilcox, 750 psi, 750F Superheat, low NOx, gas (future #2 oil), 5 ppm NOx option, new Show item detail
Nationwide Boiler Inc, Fremont, CA 800-227-1966 (Fax 510-490-0571) Larry Day
CIRCUIT BREAKERS, GAS, INDOOR TYPE
1250 Amps, ABB, Sace, SF6, 30KV, breaker (2)
Surplec HV Solutions, Sherbrooke, QC 819-821-3636 (Fax 819-563-7517) Roland/Sylvain
CIRCUIT BREAKERS, INDOOR TYPE, VACUUM
600 Amps, Cutler-Hammer, 270VCP-W22, 25 KV, vacuum, (2)
Surplec HV Solutions, Sherbrooke, QC 819-821-3636 (Fax 819-563-7517) Roland/Sylvain
2000 Amps, Cutler-Hammer, 50VCP-W250, vacuum
Surplec HV Solutions, Sherbrooke, QC 819-821-3636 (Fax 819-563-7517) Roland/Sylvain
DISTRIBUTION CENTERS (PANELS), SWITCHBOARDS
Complete high voltage power distribution center Show photo of item Show item detail
Hilco Industrial LLC, Farmington Hills, MI 248-419-1964 (Fax 248-254-9995) Ken Planet
ENGINES, DIESEL, w/o Generators (Also See Generators, Diesel Driven)
325 HP Caterpillar #C-10, Industrial diesel engine, 0 hours, 2007 Show photo of item
Quinn Power Systems, City Of Industry, CA 562-463-6073 (Fax 562-463-7156) Tom Reddy
GEAR INCREASERS, Without Driving Unit
Jake Gearbox, PSC950-39/50, new never used, on factory skid, 730 kW, 2011, $42, 000 Show photo of item
E & M Equipment LLC, Goleta, CA 805-879-5270 (Fax 805-413-4035) Ed Csapo
GENERATORS, A.C., DIESEL ENGINE DRIVEN, 60 CYCLE
20 KW Generac generator, SA enclosure, 231/400 V., 2012, #86803 Show photo of item Show item detail
Diesel Service & Supply, Brighton, CO 866-654-1355 (Fax 303-659-7923) Eddie Vecchiarelli
35 KW Cummins diesel generator, SA enclosure, 240 V., 341.6 hours, 2004, #86687 Show photo of item Show item detail
Diesel Service & Supply, Brighton, CO 866-654-1355 (Fax 303-659-7923) Eddie Vecchiarelli
60 KW Generac diesel generator, open, 208 V., 2.5 hours, 2005, #86743 Show photo of item Show item detail
Diesel Service & Supply, Brighton, CO 866-654-1355 (Fax 303-659-7923) Eddie Vecchiarelli
75 KW Olympian #XQ75, rental pkg, s/n #F4378K7001, 93.8 KVA, 208/480 V., 1800 RPM Show photo of item
E & M Equipment LLC, Goleta, CA 805-879-5270 (Fax 805-413-4035) Ed Csapo
78 KW Magnum #MMG100, diesel, multi-voltage, SAE, trailer, 2015, #4367 Show photo of item
Global Power Supply, Santa Barbara, CA 805-683-3828 (Fax 805-683-3823) Sandy Tubis
78 KW Magnum #MMG100, diesel, multi-voltage, SAE, trailer, 2015, #4645 Show photo of item
Global Power Supply, Santa Barbara, CA 805-683-3828 (Fax 805-683-3823) Sandy Tubis
78 KW Magnum #MMG100, diesel, multi-voltage, SAE, trailer, 2015, #4644 Show photo of item
Global Power Supply, Santa Barbara, CA 805-683-3828 (Fax 805-683-3823) Sandy Tubis
78 KW Magnum #MMG100, diesel, multi-voltage, SAE, trailer, 2015, #4368 Show photo of item
Global Power Supply, Santa Barbara, CA 805-683-3828 (Fax 805-683-3823) Sandy Tubis
93 KW Magnum #MMG120, diesel, multi-voltage, SAE, trailer, 2015, #4369 Show photo of item
Global Power Supply, Santa Barbara, CA 805-683-3828 (Fax 805-683-3823) Sandy Tubis
93 KW Magnum #MMG120, diesel, multi-voltage, SAE, trailer, 2015, #4647 Show photo of item
Global Power Supply, Santa Barbara, CA 805-683-3828 (Fax 805-683-3823) Sandy Tubis
93 KW Magnum #MMG120, diesel, multi-voltage, SAE, trailer, 2015, #4646 Show photo of item
Global Power Supply, Santa Barbara, CA 805-683-3828 (Fax 805-683-3823) Sandy Tubis
93 KW Magnum #MMG120, diesel, multi-voltage, SAE, trailer, 2015, #4370 Show photo of item
Global Power Supply, Santa Barbara, CA 805-683-3828 (Fax 805-683-3823) Sandy Tubis
144 KW MQ Power #DCA180SSJU, diesel, 480 V., encl, trailer, 5067 hours, 2007, #4021 Show photo of item
Global Power Supply, Santa Barbara, CA 805-683-3828 (Fax 805-683-3823) Sandy Tubis
144 KW MQ Power #DCA180SSK, diesl, 480 V., encl, trailer, 7543 hours, 2000, #4296 Show photo of item
Global Power Supply, Santa Barbara, CA 805-683-3828 (Fax 805-683-3823) Sandy Tubis
150 KW Cummins generator, full enclosure, #86876
Diesel Service & Supply, Brighton, CO 866-654-1355 (Fax 303-659-7923) Eddie Vecchiarelli
150 KW MQ Power #DCA-150SSK, genset, 480 V., 6500 hrs, enclosed with fuel tank, $13k
Power Generation Enterprises, North Hollywood, CA 818-484-8550 (Fax 818-660-2283) Victor Seropian
175 KW Caterpillar diesel generator, #86873 Show photo of item Show item detail
Diesel Service & Supply, Brighton, CO 866-654-1355 (Fax 303-659-7923) Eddie Vecchiarelli
200 KW Cummins diesel generator, SA enclosure, 480 V., 24 hours, 2012, #86877
Diesel Service & Supply, Brighton, CO 866-654-1355 (Fax 303-659-7923) Eddie Vecchiarelli
225 KW Cat #C9 engine genset, 600V, reconnectable to 480V, approx 1000hrs, open, skid mounted. Price: $33k
Power Generation Enterprises, North Hollywood, CA 818-484-8550 (Fax 818-660-2283) Victor Seropian
250 KW Cummins diesel generator, WP enclosure, 480 V., Tier 3, 2006, #86595
Diesel Service & Supply, Brighton, CO 866-654-1355 (Fax 303-659-7923) Eddie Vecchiarelli
256 KW Magnum #MMG320, diesel, multi-voltage, SAE, trailer, 2015, #4371 Show photo of item
Global Power Supply, Santa Barbara, CA 805-683-3828 (Fax 805-683-3823) Sandy Tubis
264 KW Multiquip #DCA300, SA, trlr mtd, breaker, rental type unit, Tier 4i, 1435 hrs, 2011 Show photo of item
Holt Power Systems, Corpus Christi, TX 361-698-5727 (Fax 361-852-3237) David Dennie
300 KW Cat #3406 Engine, generator set, 480 V., 150 hrs., WP enclosure, fuel tank, $25k Show photo of item
Power Generation Enterprises, North Hollywood, CA 818-484-8550 (Fax 818-660-2283) Victor Seropian
300 KW Kohler diesel generator, WP enclosure, 480 V., 325 hours, 2003, #86878
Diesel Service & Supply, Brighton, CO 866-654-1355 (Fax 303-659-7923) Eddie Vecchiarelli
310 KW Cat #3408, 480 V., open skid, panel, breaker, elec start, jw heater, 1135 hrs, 1981 Show photo of item
Holt Power Systems, Corpus Christi, TX 361-698-5727 (Fax 361-852-3237) David Dennie
320 KW MQ Power #DCA400SSV, diesel, 480 V., encl, trailer, 7678 hours, 2008, #4269 Show photo of item
Global Power Supply, Santa Barbara, CA 805-683-3828 (Fax 805-683-3823) Sandy Tubis
375 KW Cat #3406 engine genset, 600V, approx 500hrs, open, skid mounted. emcp controller. Price: $29.5k
Power Generation Enterprises, North Hollywood, CA 818-484-8550 (Fax 818-660-2283) Victor Seropian
400 KW Generac diesel generator, 480 V., 1036.9 hours, 2009, #86818 Show photo of item Show item detail
Diesel Service & Supply, Brighton, CO 866-654-1355 (Fax 303-659-7923) Eddie Vecchiarelli
500 KW Cummins diesel generator, SA enclosure, 480 V., 2004, #86874 Show photo of item Show item detail
Diesel Service & Supply, Brighton, CO 866-654-1355 (Fax 303-659-7923) Eddie Vecchiarelli
500 KW Cummins diesel generator, SA enclosure, 480 V., 2000, #86875 Show photo of item Show item detail
Diesel Service & Supply, Brighton, CO 866-654-1355 (Fax 303-659-7923) Eddie Vecchiarelli
600 KW MTU Onsite Energy #D550, genset, 550 KW prime, SAE, trailer, 277/480 V., new Show photo of item
Central Power Systems & Services, Liberty, MO 816-415-6700 (Fax 816-415-6767) Karl Roebbeke
750 KW Cummins #KTA38G, Marathon 1100 KW 4 lead 480 V. oversize generator Show photo of item Show item detail
E & M Equipment LLC, Goleta, CA 805-879-5270 (Fax 805-413-4035) Ed Csapo
800 KW Cat #APS800, diesel power module, Tier 2, 240 V., 480 V., 1105 HP, 1800 RPM Show photo of item Show item detail
Worldwide Power Products, Houston, TX 713-434-2300 (Fax 713-434-2394) Dave Vennie
800 KW Caterpillar diesel generator, SA enclosure, 480 V., 450 hours, 2002, #86871 Show photo of item Show item detail
Diesel Service & Supply, Brighton, CO 866-654-1355 (Fax 303-659-7923) Eddie Vecchiarelli
1225 KW Cat #3512C, Petroleum generator set, Tier 2, 600 V., 1476 HP, 1200 RPM, new Show photo of item Show item detail
Worldwide Power Products, Houston, TX 713-434-2300 (Fax 713-434-2394) Dave Vennie
1250 KW Cummins diesel generator, SA enclosure, 480 V., 350 hours, 2000, #86872 Show photo of item Show item detail
Diesel Service & Supply, Brighton, CO 866-654-1355 (Fax 303-659-7923) Eddie Vecchiarelli
1350 KW Deutz diesel generator, trailer mounted w/encl, 480 V., 2001, #86584 Show photo of item Show item detail
Diesel Service & Supply, Brighton, CO 866-654-1355 (Fax 303-659-7923) Eddie Vecchiarelli
1450 KW Caterpillar #3516B HD generator sets, 4160 V., 2100 HP, 1200 RPM, new Show photo of item Show item detail
Worldwide Power Products, Houston, TX 713-434-2300 (Fax 713-434-2394) Dave Vennie
1750 KW Caterpillar diesel generator, 480 V., 871 hours, 1999, #86626 Show photo of item Show item detail
Diesel Service & Supply, Brighton, CO 866-654-1355 (Fax 303-659-7923) Eddie Vecchiarelli
2000 KW Cat #3516B, diesel generator set, 2400/4160 V., 2374 HP, 1800 RPM, surplus Show photo of item Show item detail
Worldwide Power Products, Houston, TX 713-434-2300 (Fax 713-434-2394) Dave Vennie
2000 KW Cummins #DQKAB, diesel, 480 V., WPE, 83 hours, 2007, #4627 Show photo of item
Global Power Supply, Santa Barbara, CA 805-683-3828 (Fax 805-683-3823) Sandy Tubis
Multiquip #DCASSIU3, 25 KVA, trailer mounted, Isuzu diesel engine, 3512 hours Show photo of item
Quinn Power Systems, City Of Industry, CA 562-463-6073 (Fax 562-463-7156) Tom Reddy
GENERATORS, A.C., ENGINE DRIVEN, NATURAL GAS OR DUAL FUEL
85 KW Caterpillar #G3306NA, dual fuel, 480 V., WPE, trailer, 2905 hours, 2013, #4245 Show photo of item
Global Power Supply, Santa Barbara, CA 805-683-3828 (Fax 805-683-3823) Sandy Tubis
85 KW Caterpillar #G3306NA, dual fuel, 480 V., WPE, trailer, 359 hours, 2013, #4242 Show photo of item
Global Power Supply, Santa Barbara, CA 805-683-3828 (Fax 805-683-3823) Sandy Tubis
85 KW Caterpillar #G3306NA, dual fuel, 480 V., WPE, trailer, 6 hours, 2013, #4241 Show photo of item
Global Power Supply, Santa Barbara, CA 805-683-3828 (Fax 805-683-3823) Sandy Tubis
85 KW Caterpillar #G3306NA, dual fuel, 480 V., WPE, trailer, 797 hours, 2013, #4239 Show photo of item
Global Power Supply, Santa Barbara, CA 805-683-3828 (Fax 805-683-3823) Sandy Tubis
100 KW Generac Natural gas generator, WP enclosure, 480 V., 0.7 hours, 2007, #86863 Show photo of item Show item detail
Diesel Service & Supply, Brighton, CO 866-654-1355 (Fax 303-659-7923) Eddie Vecchiarelli
125 KW International Harvester #APHG150, N Gas, 480 V., WPE, trailer, 7407 hours, #4043 Show photo of item
Global Power Supply, Santa Barbara, CA 805-683-3828 (Fax 805-683-3823) Sandy Tubis
125 KW International Harvester #APHG150, N Gas, 480 V., WPE, trailer, 10741 hours, #3613 Show photo of item
Global Power Supply, Santa Barbara, CA 805-683-3828 (Fax 805-683-3823) Sandy Tubis
135 KW Caterpillar #G3306TA, dual fuel, 480 V., encl, trailer, 452 hours, 2013, #4039 Show photo of item
Global Power Supply, Santa Barbara, CA 805-683-3828 (Fax 805-683-3823) Sandy Tubis
135 KW Caterpillar #G3306TA, dual fuel, 480 V., encl, trailer, 1949 hours, 2013, #4037 Show photo of item
Global Power Supply, Santa Barbara, CA 805-683-3828 (Fax 805-683-3823) Sandy Tubis
135 KW Caterpillar #G3306TA, N Gas, 480 V., WPE, trailer, 26304 hrs, EPA Kit, 2005, #3995 Show photo of item
Global Power Supply, Santa Barbara, CA 805-683-3828 (Fax 805-683-3823) Sandy Tubis
208 KW Caterpillar #G379NA, dual fuel, 480 V., encl, trailer, 2271 hours, 2013, #4227 Show photo of item
Global Power Supply, Santa Barbara, CA 805-683-3828 (Fax 805-683-3823) Sandy Tubis
352 KW HiPower #HRNG-430 T6 portable Nat.gas genset, multi volt, 612 HP, 1800 RPM Show photo of item Show item detail
Worldwide Power Products, Houston, TX 713-434-2300 (Fax 713-434-2394) Dave Vennie
400 KW Cat #XQ400, bi-fuel (diesel/N gas), 480 V., WPE, trailer, 12896 hrs, 2006, #3617 Show photo of item
Global Power Supply, Santa Barbara, CA 805-683-3828 (Fax 805-683-3823) Sandy Tubis
400 KW Cummins #GTA28, Natural Gas, 480 V., WPE, 2117 hours, #4637 Show photo of item
Global Power Supply, Santa Barbara, CA 805-683-3828 (Fax 805-683-3823) Sandy Tubis
600 KW Caterpillar #G399TA, Natural Gas, 480 V., skid w/canopy, 8715 hours, #3612 Show photo of item
Global Power Supply, Santa Barbara, CA 805-683-3828 (Fax 805-683-3823) Sandy Tubis
800 KW Cummins #GTA50G1, Natural Gas, 480 V., SAE, rebuilt. 5430 hours, #3608 Show photo of item
Global Power Supply, Santa Barbara, CA 805-683-3828 (Fax 805-683-3823) Sandy Tubis
5320 KW Wartsila #18V34SG, Natural Gas generators, 2001 (2) Show photo of item Show item detail
E & M Equipment LLC, Goleta, CA 805-879-5270 (Fax 805-413-4035) Ed Csapo
GENERATORS, A.C., GAS OR PROPANE
45 KW Generac single phase Natural Gas generator, 1800 RPM, 120/240 V., $7, 500 Show photo of item
E & M Equipment LLC, Goleta, CA 805-879-5270 (Fax 805-413-4035) Ed Csapo
56 KW Olympian #G70LG2, Generac engine, SA enclosure, 0 hours, 2009 Show photo of item
Quinn Power Systems, City Of Industry, CA 562-463-6073 (Fax 562-463-7156) Tom Reddy
400 KW Daewoo Marathon #GV222TIC, 480V., encl, approx 6500 hrs on each (3) $29k each Show photo of item Show Video of Item
Power Generation Enterprises, North Hollywood, CA 818-484-8550 (Fax 818-660-2283) Victor Seropian
GENERATORS, A.C., WIND POWER
500 KW Baldor generator for wind turbine, spec #B794063, $24, 000.00 Show photo of item
E & M Equipment LLC, Goleta, CA 805-879-5270 (Fax 805-413-4035) Ed Csapo
ABB ACS800-104 Wind Turbine Invertor Modules (4), test hours only, $42, 000.00 Show photo of item
E & M Equipment LLC, Goleta, CA 805-879-5270 (Fax 805-413-4035) Ed Csapo
GENERATORS, D.C. OUTPUT, W/O DRIVING UNIT
120 KW, 300/1200 RPM, General Electric, Fr.CD6583, 230 V.
Illinois Electric Works Inc, Granite City, IL 618-451-6900 (Fax 618-451-6940) Dale Hamil
LIGHT TOWERS
4-1250w lamps, 30" mast, 3 sec lay down twr/360°rotat, 4 outriggers, 2530 hrs or less (9)
Holt Power Systems, Corpus Christi, TX 361-698-5727 (Fax 361-852-3237) David Dennie
4-1250w lamps, 25" mast, 6 sec hyd.vert tower, 4 outriggers, Cat eng, 1710 hrs or less (9)
Holt Power Systems, Corpus Christi, TX 361-698-5727 (Fax 361-852-3237) David Dennie
MOTORS, A.C., HOIST-DUTY, DESIGN D
HP RPM
10 HP 1675 RPM Baldor, Fr. 256T, 575 V.(6)
Duke Electric (1977) Ltd, Hamilton, ON 905-547-9171 (Fax 905-544-1522) Daniel Raab
MOTORS, A.C., SQUIRREL CAGE, 60 CYCLE (Also See Explosion Proof)
HP RPM
100 HP 1200 RPM General Electric, Fr. 8144Z, ODP, dbl shaft, 440 V.(2)
Illinois Electric Works Inc, Granite City, IL 618-451-6900 (Fax 618-451-6940) Dale Hamil
300 HP 1200 RPM Reliance, Fr. 5010, TEFC, new surplus, 4000 V.
ROI Industrial Inc, Edmonton, AB 780-903-2298 Fred Dame
300 HP 1800 RPM Baldor/Rel., fr.447/9T, TEFC, BB, 1.15, new surplus, 460V.
Ace Armature Works, Baton Rouge, LA 225-356-6175 (Fax 225-356-4744) John McCarstle
300 HP 1800 RPM Teco West, Fr. 5009B, Global series, rebuilt, 4000 V.
ROI Industrial Inc, Edmonton, AB 780-903-2298 Fred Dame
350 HP 3600 RPM Siemens, Fr. 505/506/507S, Weatherproof type II enclosure, SB, new, 2300/4000V.
Dykman Electrical, Inc., Boise, ID 208-336-3988 (Fax 208-336-3993) James Hogg
350 HP 3600 RPM Siemens, Fr. 505/506/507S, Weatherproof type II enclosure, SB, new, 2300/4000V.
Dykman Electrical, Inc., Boise, ID 208-336-3988 (Fax 208-336-3993) James Hogg
400 HP 3600 RPM Siemens, Fr. 505/506/507S, Weatherproof type II enclosure, SB, new, 2300/4000V.
Dykman Electrical, Inc., Boise, ID 208-336-3988 (Fax 208-336-3993) James Hogg
400 HP 3600 RPM Siemens, Fr. 505/506/507S, Weatherproof type II enclosure, SB, new, 2300/4000V.
Dykman Electrical, Inc., Boise, ID 208-336-3988 (Fax 208-336-3993) James Hogg
400 HP 3600 RPM U.S., Fr. 5010Z, TEFC, CW rotation, new surplus, 4160 V.
Continental Electrical Motor Services, Calgary, AB 403-236-9428 (Fax 403-279-6782) Jason Thomas
450 HP 500 RPM GE, Fr. 8311S, WPI, used, 2300v, Qty:3 Show photo of item
Transamerican Equip Co LLC, Tuscaloosa, AL 205-752-0677 (Fax 205-752-5558) Michael Friedman
450 HP 1800 RPM Baldor, Fr. 5011L, TEFC, new, 460 V.
B & H Machine Sales Inc, Detroit, MI 800-253-2505 (Fax 313-841-5553) Marc Bekolay
450 HP 3600 RPM Siemens, Fr. 505/506/507S, Weatherproof type II enclosure, SB, new, 2300/4000V.
Dykman Electrical, Inc., Boise, ID 208-336-3988 (Fax 208-336-3993) James Hogg
450 HP 3600 RPM Siemens, Fr. 505/506/507S, Weatherproof type II enclosure, SB, new, 2300/4000V.
Dykman Electrical, Inc., Boise, ID 208-336-3988 (Fax 208-336-3993) James Hogg
450 HP 3600 RPM Toshiba, Fr. 565USS, ODP, 460 V.
Electric Motors Co Inc, Hull, GA 706-549-6556 (Fax 706-546-7504) Brent Drake
900 HP 1800 RPM Reliance, Fr. 400, TEFC, new surplus, 4000 V. (2)
ROI Industrial Inc, Edmonton, AB 780-903-2298 Fred Dame
1000 HP 1190 RPM Siemens, Fr. 6811Z, TEFC BB, 2300/4160 V.(2)
Doug Beat Co The, Toledo, OH 419-865-4001 (Fax 419-865-4155) Doug/ Chris
1000 HP 1190 RPM Unimeg, Fr. 6810S & 8311S, TEFC BB, 2300/4160 V.
Doug Beat Co The, Toledo, OH 419-865-4001 (Fax 419-865-4155) Doug/ Chris
1250 HP 1800 RPM Baldor Reliance, Fr. 5810, Weatherproof type II enclosure, 2300/4000 V.
ROI Industrial Inc, Edmonton, AB 780-903-2298 Fred Dame
1500 HP 1800 RPM Reliance, Fr. 500, TEFC, new surplus, 4000 V. (3)
ROI Industrial Inc, Edmonton, AB 780-903-2298 Fred Dame
1750 HP 900 RPM Reliance, Fr. 8040S, TEFV, stator & bearing RTD' s, 4160 V.
Continental Electrical Motor Services, Calgary, AB 403-236-9428 (Fax 403-279-6782) Jason Thomas
2500 HP 3575 RPM Louis Allis, Fr. 7212DS, Weatherproof type II enclosure, sleeve, used, 4160 V.
Alliance Specialty Motors, Warrior, AL 205-590-2986 (Fax 205-590-3325) Bruce Bailey
3000 HP 1800 RPM Siemens, Fr. 6813, WP2, new surplus, 4160 V.
ROI Industrial Inc, Edmonton, AB 780-903-2298 Fred Dame
GE HP 200hp, RPM Fr.-444T, 460v, 3580rpm
Capital Machinery Systems Inc, Pendleton, IN 800-788-0307 (Fax 765-778-0919) Russ Phillips
GE HP 200hp, RPM Fr.-444TDZ, 460v, 3575rpm
Capital Machinery Systems Inc, Pendleton, IN 800-788-0307 (Fax 765-778-0919) Russ Phillips
Westinghouse HP 200hp, RPM Fr.-444TS, 460v, 3550rpm
Capital Machinery Systems Inc, Pendleton, IN 800-788-0307 (Fax 765-778-0919) Russ Phillips
Westinghouse HP 200hp, RPM Fr.-447TS, 575v, 3580rpm
Capital Machinery Systems Inc, Pendleton, IN 800-788-0307 (Fax 765-778-0919) Russ Phillips
GE HP 200hp, RPM Fr.-509DZ, 2300v, 1785rpm
Capital Machinery Systems Inc, Pendleton, IN 800-788-0307 (Fax 765-778-0919) Russ Phillips
Marathon HP 245hp, RPM Fr.-315M, 460v, 1780rpm
Capital Machinery Systems Inc, Pendleton, IN 800-788-0307 (Fax 765-778-0919) Russ Phillips
Baldor HP 250hp, RPM Fr.-445TSD, 460v, 1780rpm
Capital Machinery Systems Inc, Pendleton, IN 800-788-0307 (Fax 765-778-0919) Russ Phillips
GE HP 250hp, RPM Fr.-449T, 460v, 1790rpm
Capital Machinery Systems Inc, Pendleton, IN 800-788-0307 (Fax 765-778-0919) Russ Phillips
Siemens HP 250hp, RPM Fr.-507DZ, 4160v, 1785rpm
Capital Machinery Systems Inc, Pendleton, IN 800-788-0307 (Fax 765-778-0919) Russ Phillips
Reliance HP 300hp, RPM Fr.-445T, 460v, 1800rpm
Capital Machinery Systems Inc, Pendleton, IN 800-788-0307 (Fax 765-778-0919) Russ Phillips
GE HP 300hp, RPM Fr.-449T, 460v, 1780rpm
Capital Machinery Systems Inc, Pendleton, IN 800-788-0307 (Fax 765-778-0919) Russ Phillips
GE HP 300hp, RPM FR.-449TZ, 460v, 1785rpm
Capital Machinery Systems Inc, Pendleton, IN 800-788-0307 (Fax 765-778-0919) Russ Phillips
Baldor HP 350hp, RPM Fr.-444TS, 460v, 3550rpm
Capital Machinery Systems Inc, Pendleton, IN 800-788-0307 (Fax 765-778-0919) Russ Phillips
GE HP 350hp, RPM 509Z, 2300v, 1780rpm
Capital Machinery Systems Inc, Pendleton, IN 800-788-0307 (Fax 765-778-0919) Russ Phillips
GE HP 400hp, RPM Fr.-509Z, 4160v, 1780rpm
Capital Machinery Systems Inc, Pendleton, IN 800-788-0307 (Fax 765-778-0919) Russ Phillips
US HP Electric RPM 300hp, Fr.-447T, 460v, 1770rpm
Capital Machinery Systems Inc, Pendleton, IN 800-788-0307 (Fax 765-778-0919) Russ Phillips
GE HP 350hp, RPM Fr.-509Z, 480v, 1790rpm
Capital Machinery Systems Inc, Pendleton, IN 800-788-0307 (Fax 765-778-0919) Russ Phillips
GE HP 350hp, RPM Fr.-449TZ, 460v, 1785rpm
Capital Machinery Systems Inc, Pendleton, IN 800-788-0307 (Fax 765-778-0919) Russ Phillips
Westinghouse HP 400hp, RPM Fr.-449T, 460v, 1775rpm
Capital Machinery Systems Inc, Pendleton, IN 800-788-0307 (Fax 765-778-0919) Russ Phillips
Baldor HP 450hp, RPM Fr.-5009L, 460v, 1790rpm
Capital Machinery Systems Inc, Pendleton, IN 800-788-0307 (Fax 765-778-0919) Russ Phillips
GE HP 450hp, RPM Fr.-509Z, 4160v, 1780rpm
Capital Machinery Systems Inc, Pendleton, IN 800-788-0307 (Fax 765-778-0919) Russ Phillips
GE HP 600hp, RPM Fr.-5011Z, 575v, 1780rpm
Capital Machinery Systems Inc, Pendleton, IN 800-788-0307 (Fax 765-778-0919) Russ Phillips
Siemens HP 700hp, RPM Fr.-509UY, 2300/4000v, 3565rpm
Capital Machinery Systems Inc, Pendleton, IN 800-788-0307 (Fax 765-778-0919) Russ Phillips
GE HP 800hp, RPM Fr.-445TZ, 4160v, 1780rpm
Capital Machinery Systems Inc, Pendleton, IN 800-788-0307 (Fax 765-778-0919) Russ Phillips
GE HP 900hp, RPM Fr.-8211Z, 4160v, 1780rpm
Capital Machinery Systems Inc, Pendleton, IN 800-788-0307 (Fax 765-778-0919) Russ Phillips
MOTORS, A.C., SQUIRREL CAGE, C-FLANGE MOUNTED
HP RPM
US HP Motors RPM 200hp, Fr.-444TSC, 460v, 3560rpm
Capital Machinery Systems Inc, Pendleton, IN 800-788-0307 (Fax 765-778-0919) Russ Phillips
US HP Motors RPM 300hp, Fr.-447TSC, 460v, 3559rpm
Capital Machinery Systems Inc, Pendleton, IN 800-788-0307 (Fax 765-778-0919) Russ Phillips
MOTORS, A.C., SQUIRREL CAGE, D-FLANGE MOUNTED
HP RPM
Siemens HP 125hp, RPM Fr.-405TDZ, 460v, 1780rpm
Capital Machinery Systems Inc, Pendleton, IN 800-788-0307 (Fax 765-778-0919) Russ Phillips
Siemens HP 125hp, RPM Fr.-445TSD, 460v, VSD
Capital Machinery Systems Inc, Pendleton, IN 800-788-0307 (Fax 765-778-0919) Russ Phillips
Reliance HP 150hp, RPM Fr.-405TDZ, 460v, 1775rpm
Capital Machinery Systems Inc, Pendleton, IN 800-788-0307 (Fax 765-778-0919) Russ Phillips
GE HP 150hp, RPM Fr.-405TDZ, 460v, 3570rpm
Capital Machinery Systems Inc, Pendleton, IN 800-788-0307 (Fax 765-778-0919) Russ Phillips
Siemens HP 150hp, RPM Fr.-505TSD, 575v, 1792rpm
Capital Machinery Systems Inc, Pendleton, IN 800-788-0307 (Fax 765-778-0919) Russ Phillips
Toshiba HP 200hp, RPM Fr.-445TSD, 230/460v, 1785rpm
Capital Machinery Systems Inc, Pendleton, IN 800-788-0307 (Fax 765-778-0919) Russ Phillips
GE HP 200hp, RPM Fr.-445TSD, 460v, 1780rpm
Capital Machinery Systems Inc, Pendleton, IN 800-788-0307 (Fax 765-778-0919) Russ Phillips
Reliance HP 200hp, RPM Fr.-445TSD, 460v, 1780rpm
Capital Machinery Systems Inc, Pendleton, IN 800-788-0307 (Fax 765-778-0919) Russ Phillips
Siemens HP 250hp, RPM Fr.-315L, 460v, 1785rpm
Capital Machinery Systems Inc, Pendleton, IN 800-788-0307 (Fax 765-778-0919) Russ Phillips
Toshiba HP 250hp, RPM Fr.-315M, 2300/4160v, 1770rpm
Capital Machinery Systems Inc, Pendleton, IN 800-788-0307 (Fax 765-778-0919) Russ Phillips
Toshiba HP 250hp, RPM Fr.-315M, 2400v, 1775rpm
Capital Machinery Systems Inc, Pendleton, IN 800-788-0307 (Fax 765-778-0919) Russ Phillips
Reliance HP 250hp, RPM Fr.-445TSD, 460v, 1780rpm
Capital Machinery Systems Inc, Pendleton, IN 800-788-0307 (Fax 765-778-0919) Russ Phillips
Westinghouse HP 250hp, RPM Fr.-449TSD, 2300/4160v, 1775rpm
Capital Machinery Systems Inc, Pendleton, IN 800-788-0307 (Fax 765-778-0919) Russ Phillips
Siemens HP 250hp, RPM Fr.-505TD, 460v, 1788rpm
Capital Machinery Systems Inc, Pendleton, IN 800-788-0307 (Fax 765-778-0919) Russ Phillips
MOTORS, A.C., SYNCHRONOUS, 60 CYCLE
HP RPM
2200 HP 300 RPM Electric Machinery, Fr. 24U7216, WPI, sleeve, 2300/4000V.
Pump & Motor Works, Okmulgee, OK 918-752-0309 (Fax 918-752-0310) Sales
MOTORS, A.C., VERTICAL
HP RPM
150 HP 1800 RPM U.S., Fr. 444TP, WPI, VHS, 460 V.
Mid Kansas Winding, Galva, KS 620-654-3780 (Fax 620-654-3785) Don Sullivan
200 HP 1800 RPM U.S., Fr. 5008P, TEFC, anti-friction brgs, oil lube, 460 V.
Continental Electrical Motor Services, Calgary, AB 403-236-9428 (Fax 403-279-6782) Jason Thomas
250 HP 1800 RPM U.S., Fr. 1505PH, WPI, VHS, 460 V.(2)
Mid Kansas Winding, Galva, KS 620-654-3780 (Fax 620-654-3785) Don Sullivan
400 HP 885 RPM General Electric, Fr.L5011VP30, WPI, 1.15 S.F., oil lube RTDs
L & J Investments, Group III, Tucson, AZ 520-349-0187 (Fax 520-299-0732) Larry Flynn
MOTORS, D.C., CRANE & MILL
HP RPM
15 HP 800 RPM General Electric, Fr.MD406AE2, 230 V.(3)
Illinois Electric Works Inc, Granite City, IL 618-451-6900 (Fax 618-451-6940) Dale Hamil
MOTORS, D.C., 230-250 VOLTS, CONSTANT & VARIABLE SPEED
HP RPM
300 HP 300/1200 RPM General Electric, Fr.CDF17674, 250 V.
Illinois Electric Works Inc, Granite City, IL 618-451-6900 (Fax 618-451-6940) Dale Hamil
MOTORS, D.C., 475-900 VOLTS, CONSTANT & VARIABLE SPEED
HP RPM
50 HP 1750/2100 RPM Baldor, Fr. 328AT, DP, #D5050P, 500 VA, 150/300 VF
B & M Electric Motor Service Inc, Hickory, NC 828-267-0829 (Fax 828-267-0874) Shannon McDonald
50 HP 1750/2100 RPM Reliance, Fr.LC2512ATZ, DPFG, 500/300 V.
Power Equipment Co, Rochester, NY 888-666-7771 (Fax 585-436-5578) Al Kempf
75 HP 1750/2100 RPM Reliance, Fr.LC2812ATZ, 500/300 V.
Power Equipment Co, Rochester, NY 888-666-7771 (Fax 585-436-5578) Al Kempf
100 HP 1750/2000 RPM General Electric, Fr. 368AT, 500/300 V.
Power Equipment Co, Rochester, NY 888-666-7771 (Fax 585-436-5578) Al Kempf
125 HP 350/1200 RPM General Electric, Fr.CD1552Y, 600 V.
Illinois Electric Works Inc, Granite City, IL 618-451-6900 (Fax 618-451-6940) Dale Hamil
200 HP 1750/2100 RPM General Electric, Fr. 409AT, DPFG, 500/300 V.
Power Equipment Co, Rochester, NY 888-666-7771 (Fax 585-436-5578) Al Kempf
SWITCHES
INTERRUPTERS, INDOOR TYPE (Load Break Switches)
200 Amp. S & C, MS-10, 15KV, Nema 1, with 200 amp Fused Switch (7)
Doug Beat Co The, Toledo, OH 419-865-4001 (Fax 419-865-4155) Doug/ Chris
600 Amp. ABB metal enclosed interrupter switch, 15 KV, Bil 95 KV, 60 Hz, 2005, $20, 000 Show photo of item
E & M Equipment LLC, Goleta, CA 805-879-5270 (Fax 805-413-4035) Ed Csapo
TRANSFER SWITCHES
1200 Amp. Zenith with ABB Vacuum Breakers, 5 KV, ATS, Nema 3 outdoor enclosed Show photo of item
E & M Equipment LLC, Goleta, CA 805-879-5270 (Fax 805-413-4035) Ed Csapo
TRANSFORMERS, SINGLE PHASE, 60 CYCLE, PAD MOUNT (Padmount)
167 KVA 24940Y/14400 x 12470Y/7200 Pri. 240/120 Sec., Mini-Pad (2)
Surplec HV Solutions, Sherbrooke, QC 819-821-3636 (Fax 819-563-7517) Roland/Sylvain
TRANSFORMERS, THREE PHASE, 60 CYCLE
250 KVA 4160 Delta Pri. 480Y/277 Sec., Hammond, Core & Coil
L & J Investments, Group III, Tucson, AZ 520-349-0187 (Fax 520-299-0732) Larry Flynn
425 KVA 4160 Delta Pri. 480Y/277 Sec., Hammond, Core & Coil
L & J Investments, Group III, Tucson, AZ 520-349-0187 (Fax 520-299-0732) Larry Flynn
2500 KVA 12470 Delta Pri. 480Y/277 Sec., Core & Coil, surplus
L & J Investments, Group III, Tucson, AZ 520-349-0187 (Fax 520-299-0732) Larry Flynn
12/20 MVA 34500 Pri. 13800Y/7970 Sec., Allis-Chalmers, OA/FA/FFA, under 1 yr.use Show photo of item
River City Industrial Inc, Chattanooga, TN 423-821-4712 (Fax 423-821-7907) Philip Mantel
TRANSFORMERS, THREE PHASE, 60 CYCLE, PAD MOUNT (Padmount)
500 KVA 13800 Delta Pri. 600 Wye Sec.
Magna Electric Corporation, Saskatoon, SK 306-955-8131 (Fax 306-955-9181) Kerwin Boser
750 KVA 24940Y x 12470Y Pri. 12470 x 4160Y Sec., #T3265
Surplec HV Solutions, Sherbrooke, QC 819-821-3636 (Fax 819-563-7517) Roland/Sylvain
750 KVA 24940 Delta Pri. 600Y Sec., #T3217
Surplec HV Solutions, Sherbrooke, QC 819-821-3636 (Fax 819-563-7517) Roland/Sylvain
1000 KVA 4160 Delta Pri. 480 Wye Sec.
Magna Electric Corporation, Saskatoon, SK 306-955-8131 (Fax 306-955-9181) Kerwin Boser
1000 KVA 24940Y x 12470Y Pri. 600Y Sec., Vault, #T1284
Surplec HV Solutions, Sherbrooke, QC 819-821-3636 (Fax 819-563-7517) Roland/Sylvain
1000 KVA 13200 Delta Pri. 480Y/277 Sec., Solomon, new (2)
Solomon Corporation, Solomon, KS 800-234-2867 (Fax 785-655-2502) Ken Bryman
1000 KVA 13800 Delta Pri. 480Y/277 Sec., Solomon, new (2)
Solomon Corporation, Solomon, KS 800-234-2867 (Fax 785-655-2502) Ken Bryman
1000 KVA 13800Y Pri. 600Y Sec., #T1478
Surplec HV Solutions, Sherbrooke, QC 819-821-3636 (Fax 819-563-7517) Roland/Sylvain
1500 KVA 24940Y Pri. 4160Y Sec., (2)
Surplec HV Solutions, Sherbrooke, QC 819-821-3636 (Fax 819-563-7517) Roland/Sylvain
2500 KVA 4160 Delta Pri. 480Y/277 Sec., Solomon, new (2)
Solomon Corporation, Solomon, KS 800-234-2867 (Fax 785-655-2502) Ken Bryman
2500 KVA 12470 Delta Pri. 480Y/277 Sec., Solomon, new (2)
Solomon Corporation, Solomon, KS 800-234-2867 (Fax 785-655-2502) Ken Bryman
2500 KVA 13200 Delta Pri. 480Y/277 Sec., Solomon, new (2)
Solomon Corporation, Solomon, KS 800-234-2867 (Fax 785-655-2502) Ken Bryman
2500 KVA 13800 Delta Pri. 480Y/277 Sec., Solomon, new (2)
Solomon Corporation, Solomon, KS 800-234-2867 (Fax 785-655-2502) Ken Bryman

Surplus Record Surplus Record All Rights Reserved.
https://www.surplusrecord.com
Tel: 312-372-9077        Customer Service        Mobile Apps        Advertise