7/8"Cap, T-DRILL, No. TCC-50-EF02, 2003, TUBE CUTTING & END FORMING LINE
Our stock number: 10963



SPECIFICATIONS:
MANUFACTURER: T-DRILL INDUSTRIES (FINLAND)
MODEL No.: TCC-50-EF20
YEAR OF MANUFACTURE: 2003

TYPE: TUBE CUTOFF MACHINE WITH IN-LINE END FORMER & AUTOMATIC WORK CYCLE.

APPLICATIONS: SUITABLE FOR COPPER OR ALUMINUM IN COIL FORM. CAN BE USED AS A CUTOFF ONLY OR WITH THE IN-LINE END FORMER FOR NOTCHES, FLANGES, COLLARS, ETC.

MAXIMUM DIAMETER OF TUBE (CUTOFF ONLY): 22mm (7/8")
MAXIMUM DIAMETER FOR CUT & END FORM: 8mm - 16mm (0.31"- 0.625")
MAXIMUM DIAMETER OF END FORMED SHAPE: 22mm (7/8")

WALL THICKNESS: 0.4mm - 1.5mm (.020"-.060")
HEIGHT OF TUBE LINE ABOVE FLOOR: 1100mm (43")
MACHINE WEIGHT: 1900 KG (4200 LBS.)
MAXIMUM NOISE LEVEL: 80 DB
COMPRESSED AIR SUPPLY: 6 BAR = 600 KPA
POWER: 6.5 kW
SUPPLY VOLTAGE: 200/415 VOLT/50 HZ
200/480 VOLT/60 HZ
PAYOFF:
THE COIL EQUIPMENT CONSIST OF TWO DIFFERENT UNITS: THE DOUBLE HOLDER AND THE TENSION UNIT. THE DOUBLE COIL HOLDER IS A UNIT FOR UNCOILING THE TUBE.

THE TENSION UNIT IS A COMPRESSED AIR DRIVEN UNCOILING DEVICE, WHICH ABSORBS JERKS EXERCISED ON THE COIL AND CONTROLS THE UNCOILING SPEED. THE UNCOILING EQUIPMENT IS CONNECTED TO THE CONTROL UNIT OF THE MAIN MACHINE.

TUBE STRAIGHTENER:
THE STRAIGHTENER CONSISTS VERTICAL AND HORIZONTAL ROLLS, WHICH ARE USED TO STRAIGHTEN COIL FED TUBE. EVERY TUBE DIAMETER REQUIRES A CORRESPONDING SET OF STRAIGHTENING ROLLS.

PINCH ROLL STATION:
SOME LARGE COIL FED TUBE IS INITIALLY STRAIGHTENED BY A PINCH ROLL STATION TO TAKE OUT THE COIL SET. WHEN TUBE O.D. IS MORE THAN 12mm (1/2") OR IT REQUIRES ROUND CONDITION, PINCH ROLL STATION IS USED.

THE CUTTING METHODS OF TUBE:

THE MACHINE CAN BE USED ONE OF THREE METHODS TO CUT THE TUBE.

1. THROUGH CUT METHOD:
THE BLADE PENETRATES THE TUBE WALL. THIS METHOD CAN BE USED FOR CUT
LENGTHS OF 200mm (7/8")   LENGTH OF END FORMING. IF ONLY A THROUGH CUT IS CARRIED OUT, THE MINIMUM CUT LENGTH IS 150mm (6"). THROUGH CUT CAUSES SOME I.D. REDUCTION.

2. CUT & PULL APART METHOD:
THE BLADE PENETRATES ABOUT 90% THROUGH THE TUBE WALL AND A POWERED MOVEMENT OF THE OUTBOARD CLAMP PULLS THE TUBE APART. PULL-APART METHOD IS USED WHEN I.D. REDUCTION NEEDS TO BE MINIMIZED. THE METHOD IS USED FOR CUT LENGTHS MINIMUM 200mm (7/8")   LENGTH OF END FORMING. IF ONLY AN INCISION AND PULL APART IS CARRIED OUT, THE MINIMUM CUT LENGTH IS 150mm (6").

3. CUT AND BREAK METHOD:
THE BLADE PENETRATES ABOUT 90% THROUGH THE TUBE WALL AND AN AIR CYLINDER BREAKS THE TUBE OFF FROM THE SIDE. THIS METHOD IS USED FOR CUT LENGTHS SHORTER THAN 200mm (7/8"). MINIMUM CUT LENGTH IS 3 TIMES TUBE O.D. WHEN END FORMING IS USED, THE CUT LENGTH IS MINIMUM 3 TIMES TUBE O.D. AND MAXIMUM < 200mm (7.2")   LENGTH OF END FORMING.

TOOLING:
THE LINE IS PRESENTLY TOOLED FOR 7.64mm AND 6.36mm TUBE AND WAS PREVIOUSLY USED ON COPPER REFRIGERATION TUBE TO MAKE HEAT EXCHANGERS AND SKIN CONDENSERS. THE MACHINE CAN BE RETOOLED TO HANDLE A VARIETY OF END FORMING APPLICATIONS, INCLUDING FLANGES, COLLARS, NOTCHES, ETC. THE MANUFACTURER IS AVAILABLE TO SUPPLY PARTS AND TECHNICAL ASSISTANCE.

**PRICE QUOTED IS EX WORKS AS IS WHERE IS SUBJECT TO PRIOR SALE**

**ALL SPECIFICATIONS ARE SUBJECT TO VERIFICATION BY PURCHASER**