MATERIAL: CR, GALV., ALUMINUM, STAINLESS
GAUGE RANGE: 0.010" - 0.137"
WIDTH TOLERANCES:  /- 0.005"
WIDTH RANGE: 20" - 60"
MAXIMUM COIL WEIGHT: 40,000 LBS.
COIL I.D. RANGE: 16" TO 24"
COIL O.D.: 72"
SIDE TRIM: 0.375" TOTAL (MINIMUM)
LINE SPEED: 400 OR 800 FPM (2 SPEED)
THREAD SPEED: 75 FPM
DIRECTION OF FEED: LEFT TO RIGHT
CAPACITY: 8 CUTS OF 0.115" (45,000 PSI) AT 400 FPM
15 CUTS OF 0.053" (45,000 PSI) AT 800 FPM
POWER SUPPLY: 460 VOLT, 3 PH, 60 HZ.
CONTROL POWER SUPPLY: 110 VOLT, 1 PH, 60 HZ.

CONSISTING OF THE FOLLOWING:

-4 ARM ENTRY TURNSTILE:
MACHINE NO.: 4381
SALES NO.: 288 81 7A
53" ARM LENGTH
SWING RADIUS: 84.5"
HYDRAULIC ROTATION
HYDRAULIC LOCK
C-HOOK TYPE ARMS W/7" W x 10.25" H SLOT
PASSLINE: 49" FROM FLOOR TO TOP OF ARM
OVERALL SIZE: 169" L x 62" W x 53" HIGH

-MANDREL TYPE UNCOILER:
MACHINE NO.: 4381
SALES NO.: 288 81 9A
HYDRAULIC EXPANSION
11.5" DIA. MAIN SHAFT
65" FACE MANDREL
(4) SEGMENT MANDREL
16" - 20" I.D. W/24" PADS
TRAVERSING BASE
POWERED HOLDDOWN ROLL
8" DIA. x 24" FACE ROLL
RUBBER COVERED W/BANDING SLOT
HYD. MOTOR DRIVEN
AC MOTOR THREADING DRIVE W/AIR CLUTCH
WICHITA WATER COOLED BRAKE
PASSLINE: 40" FROM FLOOR TO CENTER OF MANDREL
OVERALL SIZE: 180" L x 73" W x 82" HIGH

-NORTH AMERICAN EDGE GUIDE SENSOR

-ENTRY PEELER TABLE:
HYD. UP/DOWN, IN/OUT
ENTRY DRIVEN PINCH ROLLS
6" DIA. x 66" FACE
ENTRY EDGE GUIDE ROLLERS

-ROTARY KNIFE CROP SHEAR

-(2) REMOVABLE SLITTER HEADS:
MACHINE NO.: 4381
SALES NO.: 288 81 13A
6.50" DIA. x 63.5" FACE ARBORS
PARALLEL TOP ARBOR ADJUSTMENT
JET NUTS
75 HP DC DRIVE MOTOR, 1150/2000 RPM, 500 V
2 SPEED BOX W/4.148 AND 8.296:1 RATIO'S
QUICK CHANGE DISCONNECTS
HYDRAULIC POWER STAND CLAMPING
OVERALL SIZE: 155" L x 38" W x 82" HIGH

-(2) SCRAP WINDERS
HYDRAULIC OSCILLATION
AUTO DUMP

-LOOPING PIT WITH RETRACTABLE THREADING TABLE
ENTRY/EXIT GUIDE ROLLS

-SYNCROWIND TENSION STAND
MACHINE NO.: 4381
SALES NO.: 288 81 17A
COMBINATION PAD/ROLL TYPE
ENTRY SEPARATOR TOOLING BAR
ENTRY STRIP HOLDDOWN ROLL
ENTRY PASSLINE ROLL
DRAG WIPE PADS
AIR BAG OPERATED
POLYURETHANE COATED ROLLS
16" DIA. x 64.625" FACE WIDTH
WICHITA WATER COOLED BRAKE ON BOTTOM ROLL
EXIT CROP SHEAR
UPCUT TYPE
66" LONG BLADE
EXIT PASSLINE ROLL W/TACH GENERATOR
14" DIA. x 66" FACE WIDTH
POLYURETHANE COATED
EXIT THREADING TABLE
OVERALL SIZE: 106" L x 85" W x 78" HIGH

-RECOILER: NEW IN 1985
SALES NO.: 466 85 18A
16" DIA. x 66" FACE DRUM (30,000# CAPACITY)
DRUM AND SHAFT ASSEMBLY
10.25" DIA. MAIN SHAFT
20" DIA. x 66" FACE DRUM (40,000# CAPACITY)
DRUM AND SHAFT ASSEMBLY
12" DIA. MAIN SHAFT
24" DIA. BOLT ON PADS
POWERED CLAMP AND EXPANSION
HYDRAULIC PUSHOFF
OVERARM SEPARATOR
100 HP GE DC MOTOR W/BLOWER & HOLDING BRAKE
650/1950 RPM, 500 V
H&S MARK II HELICAL SPEED REDUCER
RATED AT 100 HP @ 650 RPM INPUT
2 SPEEDS: 12.76 & 25.51:1 RATIOS
PASSLINE: 40" FROM FLOOR TO CENTER OF DRUM
OVERALL SIZE: 195" L x 96" W x 97" HIGH

-EXIT COIL CAR
ABOVE FLOOR TYPE "L" DESIGN
66" WIDE BED
72" O.D. CAPACITY
APPROX. 10" FROM FLOOR TO BOTTOM OF "V" CRADLE
NARROW COIL RETAINING ARMS
SELF CONTAINED HYDRAULICS
6" BORE HANNA HYDRAULIC LIFT CYLINDER
RETRACTABLE CABLE REEL
OVERALL SIZE: 96" L x 66" W x 60" HIGH

-4 ARM EXIT TURNSTILE:
MACHINE NO.: 4381
SALES NO.: 288 81 20A
76.75" ARM LENGTH
SWING RADIUS: 108.25"
HYDRAULIC ROTATION
HYDRAULIC LOCK
HYDRAULIC PUSHOFF
C-HOOK TYPE ARMS W/7" W x 14" H SLOT
PASSLINE: 49" FROM FLOOR TO TOP OF ARM
OVERALL SIZE: 216.5" L x 64" W x 82" HIGH

-CENTRAL OPERATORS CONTROL CONSOLE

-MOTOR CONTROL SWITCHGEAR

-TOOLING INCLUDING KNIVES, SPACERS, RUBBERS & SHIMS

-REMOVED AND IN STORAGE; TOLEDO, OH.